[lkml]   [2022]   [Jun]   [28]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
Messages in this thread
Subject[PATCH v11 net-next 0/9] add support for VSC7512 control over SPI
The patch set in general is to add support for the VSC7512, and
eventually the VSC7511, VSC7513 and VSC7514 devices controlled over
SPI. Specifically this patch set enables pinctrl, serial gpio expander
access, and control of an internal and an external MDIO bus.

I have mentioned previously:
The hardware setup I'm using for development is a beaglebone black, with
jumpers from SPI0 to the microchip VSC7512 dev board. The microchip dev
board has been modified to not boot from flash, but wait for SPI. An
ethernet cable is connected from the beaglebone ethernet to port 0 of
the dev board. Network functionality will be included in a future patch set.

The device tree I'm using is included in the documentation, so I'll not
include that in this cover letter. I have exported the serial GPIOs to the
LEDs, and verified functionality via
"echo heartbeat > sys/class/leds/port0led/trigger"

/ {
vscleds {
compatible = "gpio-leds";
vscled@0 {
label = "port0led";
gpios = <&sgpio_out1 0 0 GPIO_ACTIVE_LOW>;
default-state = "off";
vscled@1 {
label = "port0led1";
gpios = <&sgpio_out1 0 1 GPIO_ACTIVE_LOW>;
default-state = "off";
[ ... ]

And I'll include the relevant dmesg prints - I don't love the "invalid
resource" prints, as they seem to be misleading. They're a byproduct of
looking for IO resources before falling back to REG, which succeeds.

Booting Linux on physical CPU 0x0
Linux version 5.19.0-rc3-00662-gb661f062e865
[ 1.930121] pinctrl-ocelot DMA mask not set
[ 1.930287] pinctrl-ocelot invalid resource
[ 1.930861] gpiochip_find_base: found new base at 2026
[ 1.930912] gpio gpiochip4: (ocelot-gpio): created GPIO range 0->21 ==> PIN 0->21
[ 1.933211] gpio gpiochip4: (ocelot-gpio): added GPIO chardev (254:4)
[ 1.933358] gpio gpiochip4: registered GPIOs 2026 to 2047 on ocelot-gpio
[ 1.933378] pinctrl-ocelot driver registered
[ 1.951876] pinctrl-microchip-sgpio DMA mask not set
[ 1.952100] pinctrl-microchip-sgpio invalid resource
[ 1.952971] gpiochip_find_base: found new base at 1962
[ 1.953710] gpio_stub_drv gpiochip5: ( added GPIO chardev (254:5)
[ 1.953822] gpio_stub_drv gpiochip5: registered GPIOs 1962 to 2025 on
[ 1.954612] gpiochip_find_base: found new base at 1898
[ 1.955513] gpio_stub_drv gpiochip6: ( added GPIO chardev (254:6)
[ 1.955611] gpio_stub_drv gpiochip6: registered GPIOs 1898 to 1961 on
[ 1.963280] mscc-miim DMA mask not set
[ 1.963432] mscc-miim invalid resource
[ 1.963585] mscc-miim invalid resource
[ 1.964633] mdio_bus GPIO lookup for consumer reset
[ 1.964651] mdio_bus using device tree for GPIO lookup
[ 1.964676] of_get_named_gpiod_flags: can't parse 'reset-gpios' property of node '/ocp/interconnect@48000000/segment@0/target-module@30000/spi@0/switch@0/mdio@7107009c[0]'
[ 1.964767] of_get_named_gpiod_flags: can't parse 'reset-gpio' property of node '/ocp/interconnect@48000000/segment@0/target-module@30000/spi@0/switch@0/mdio@7107009c[0]'
[ 1.964857] mdio_bus using lookup tables for GPIO lookup
[ 1.964868] mdio_bus No GPIO consumer reset found

I only have hardware to test the last patch, so any testers are welcome.
I've been extra cautious about the
ocelot_platform_init_regmap_from_resource helper function, both before
and after the last patch. I accidentally broke it in the past and would
like to avoid doing so again.

RFC history:
v1 (accidentally named vN)
* Initial architecture. Not functional
* General concepts laid out

* Near functional. No CPU port communication, but control over all
external ports
* Cleaned up regmap implementation from v1

* Functional
* Shared MDIO transactions routed through mdio-mscc-miim
* CPU / NPI port enabled by way of vsc7512_enable_npi_port /
* NPI port tagging functional - Requires a CPU port driver that supports
frames of 1520 bytes. Verified with a patch to the cpsw driver

* Functional
* Device tree fixes
* Add hooks for pinctrl-ocelot - some functionality by way of sysfs
* Add hooks for pinctrl-microsemi-sgpio - not yet fully functional
* Remove lynx_pcs interface for a generic phylink_pcs. The goal here
is to have an ocelot_pcs that will work for each configuration of
every port.

* Restructured to MFD
* Several commits were split out, submitted, and accepted
* pinctrl-ocelot believed to be fully functional (requires commits
from the linux-pinctrl tree)
* External MDIO bus believed to be fully functional

* Applied several suggestions from the last RFC from Lee Jones. I
hope I didn't miss anything.
* Clean up MFD core - SPI interaction. They no longer use callbacks.
* regmaps get registered to the child device, and don't attempt to
get shared. It seems if a regmap is to be shared, that should be
solved with syscon, not dev or mfd.

* Applied as much as I could from Lee and Vladimir's suggestions. As
always, the feedback is greatly appreciated!
* Remove "ocelot_spi" container complication
* Move internal MDIO bus from ocelot_ext to MFD, with a devicetree
change to match
* Add initial HSIO support
* Switch to IORESOURCE_REG for resource definitions

* Applied another round of suggestions from Lee and Vladimir
* Utilize regmap bus reads, which speeds bulk transfers up by an
order of magnitude
* Add two additional patches to utilize phylink_generic_validate
* Changed GPL V2 to GPL in licenses where applicable (checkpatch)
* Remove initial hsio/serdes changes from the RFC

* Submitting as a PATCH instead of an RFC
* Remove switch functionality - will be a separate patch set
* Remove Kconfig tristate module options
* Another round of suggestions from Lee, Vladimir, and Andy. Many
* Add documentation
* Update maintainers

* Fix warming by removing unused function

* Suggestions from Rob and Andy. Thanks!
* Add pinctrl module functionality back and fixing those features
* Fix aarch64 compiler error

Colin Foster (9):
mfd: ocelot: add helper to get regmap from a resource
net: mdio: mscc-miim: add ability to be used in a non-mmio
pinctrl: ocelot: allow pinctrl-ocelot to be loaded as a module
pinctrl: ocelot: add ability to be used in a non-mmio configuration
pinctrl: microchip-sgpio: allow sgpio driver to be used as a module
pinctrl: microchip-sgpio: add ability to be used in a non-mmio
resource: add define macro for register address resources
dt-bindings: mfd: ocelot: add bindings for VSC7512
mfd: ocelot: add support for the vsc7512 chip via spi

.../devicetree/bindings/mfd/mscc,ocelot.yaml | 160 +++++++++
drivers/mfd/Kconfig | 18 +
drivers/mfd/Makefile | 2 +
drivers/mfd/ocelot-core.c | 175 ++++++++++
drivers/mfd/ocelot-spi.c | 313 ++++++++++++++++++
drivers/mfd/ocelot.h | 28 ++
drivers/net/mdio/mdio-mscc-miim.c | 35 +-
drivers/pinctrl/Kconfig | 4 +-
drivers/pinctrl/pinctrl-microchip-sgpio.c | 14 +-
drivers/pinctrl/pinctrl-ocelot.c | 15 +-
include/linux/ioport.h | 5 +
include/linux/mfd/ocelot.h | 35 ++
13 files changed, 773 insertions(+), 38 deletions(-)
create mode 100644 Documentation/devicetree/bindings/mfd/mscc,ocelot.yaml
create mode 100644 drivers/mfd/ocelot-core.c
create mode 100644 drivers/mfd/ocelot-spi.c
create mode 100644 drivers/mfd/ocelot.h
create mode 100644 include/linux/mfd/ocelot.h


 \ /
  Last update: 2022-06-28 10:21    [W:0.174 / U:0.444 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site