lkml.org 
[lkml]   [2022]   [May]   [2]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v4 06/13] ARM: dts: lan966x: add flexcom I2C nodes
Date
Add all I2C nodes of the flexcom IP blocks. The driver supports
FIFO, DMA or both combined. But the latter isn't working correctly.
Thus, skip the fifo-size property for now. DMA is doing single byte
reads in this case.

Keep the nodes disabled by default.

Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
---
arch/arm/boot/dts/lan966x.dtsi | 65 ++++++++++++++++++++++++++++++++++
1 file changed, 65 insertions(+)

diff --git a/arch/arm/boot/dts/lan966x.dtsi b/arch/arm/boot/dts/lan966x.dtsi
index a37f2e58a1c2..342c8cee2b9a 100644
--- a/arch/arm/boot/dts/lan966x.dtsi
+++ b/arch/arm/boot/dts/lan966x.dtsi
@@ -120,6 +120,19 @@ spi0: spi@400 {
#size-cells = <0>;
status = "disabled";
};
+
+ i2c0: i2c@600 {
+ compatible = "microchip,sam9x60-i2c";
+ reg = <0x600 0x200>;
+ interrupts = <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>;
+ dmas = <&dma0 AT91_XDMAC_DT_PERID(3)>,
+ <&dma0 AT91_XDMAC_DT_PERID(2)>;
+ dma-names = "tx", "rx";
+ clocks = <&nic_clk>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
};

flx1: flexcom@e0044000 {
@@ -158,6 +171,19 @@ spi1: spi@400 {
#size-cells = <0>;
status = "disabled";
};
+
+ i2c1: i2c@600 {
+ compatible = "microchip,sam9x60-i2c";
+ reg = <0x600 0x200>;
+ interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>;
+ dmas = <&dma0 AT91_XDMAC_DT_PERID(5)>,
+ <&dma0 AT91_XDMAC_DT_PERID(4)>;
+ dma-names = "tx", "rx";
+ clocks = <&nic_clk>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
};

trng: rng@e0048000 {
@@ -213,6 +239,19 @@ spi2: spi@400 {
#size-cells = <0>;
status = "disabled";
};
+
+ i2c2: i2c@600 {
+ compatible = "microchip,sam9x60-i2c";
+ reg = <0x600 0x200>;
+ interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>;
+ dmas = <&dma0 AT91_XDMAC_DT_PERID(7)>,
+ <&dma0 AT91_XDMAC_DT_PERID(6)>;
+ dma-names = "tx", "rx";
+ clocks = <&nic_clk>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
};

flx3: flexcom@e0064000 {
@@ -251,6 +290,19 @@ spi3: spi@400 {
#size-cells = <0>;
status = "disabled";
};
+
+ i2c3: i2c@600 {
+ compatible = "microchip,sam9x60-i2c";
+ reg = <0x600 0x200>;
+ interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>;
+ dmas = <&dma0 AT91_XDMAC_DT_PERID(9)>,
+ <&dma0 AT91_XDMAC_DT_PERID(8)>;
+ dma-names = "tx", "rx";
+ clocks = <&nic_clk>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
};

dma0: dma-controller@e0068000 {
@@ -308,6 +360,19 @@ spi4: spi@400 {
#size-cells = <0>;
status = "disabled";
};
+
+ i2c4: i2c@600 {
+ compatible = "microchip,sam9x60-i2c";
+ reg = <0x600 0x200>;
+ interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>;
+ dmas = <&dma0 AT91_XDMAC_DT_PERID(11)>,
+ <&dma0 AT91_XDMAC_DT_PERID(10)>;
+ dma-names = "tx", "rx";
+ clocks = <&nic_clk>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
};

timer0: timer@e008c000 {
--
2.30.2
\
 
 \ /
  Last update: 2022-05-03 00:42    [W:0.440 / U:0.096 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site