lkml.org 
[lkml]   [2022]   [May]   [13]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
SubjectRE: [PATCH v3 5/5] pinctrl: renesas: pinctrl-rzg2l: Add IRQ domain to handle GPIO interrupt
Date


> -----Original Message-----
> From: Biju Das
> Sent: 12 May 2022 18:59
> To: Lad, Prabhakar <prabhakar.csengg@gmail.com>
> Cc: Prabhakar Mahadev Lad <prabhakar.mahadev-lad.rj@bp.renesas.com>; Geert
> Uytterhoeven <geert+renesas@glider.be>; Linus Walleij
> <linus.walleij@linaro.org>; Thomas Gleixner <tglx@linutronix.de>; Marc
> Zyngier <maz@kernel.org>; Rob Herring <robh+dt@kernel.org>; Krzysztof
> Kozlowski <krzysztof.kozlowski+dt@linaro.org>; Bartosz Golaszewski
> <brgl@bgdev.pl>; Philipp Zabel <p.zabel@pengutronix.de>; linux-
> gpio@vger.kernel.org; linux-kernel@vger.kernel.org; linux-renesas-
> soc@vger.kernel.org; devicetree@vger.kernel.org; Phil Edworthy
> <phil.edworthy@renesas.com>
> Subject: RE: [PATCH v3 5/5] pinctrl: renesas: pinctrl-rzg2l: Add IRQ domain
> to handle GPIO interrupt
>
> Hi Prabhakar,
>
> > Subject: Re: [PATCH v3 5/5] pinctrl: renesas: pinctrl-rzg2l: Add IRQ
> > domain to handle GPIO interrupt
> >
> > Hi Biju,
> >
> > Thank you for the review.
> >
> > On Thu, May 12, 2022 at 6:35 AM Biju Das <biju.das.jz@bp.renesas.com>
> > wrote:
> > >
> > > Hi Prabhakar,
> > >
> > > Thanks for the patch.
> > >
> > > > Prabhakar Mahadev Lad <prabhakar.mahadev-lad.rj@bp.renesas.com>
> > > > Subject: [PATCH v3 5/5] pinctrl: renesas: pinctrl-rzg2l: Add IRQ
> > > > domain to handle GPIO interrupt
> > > >
> > > > Add IRQ domian to RZ/G2L pinctrl driver to handle GPIO interrupt.
> > > >
> > > > GPIO0-GPIO122 pins can be used as IRQ lines but only 32 pins can
> > > > be used as IRQ lines at given time. Selection of pins as IRQ lines
> > > > is handled by IA55 (which is the IRQC block) which sits in between
> > > > the
> > GPIO and GIC.
> > >
> > > Do we need to update bindings with interrupt-cells on [1] like [2]
> > > as it
> > act as parent for GPIO interrupts?
> > >
> > Yes interrupt-controller and interrupt-parent needs to be added. I'm
> > wondering if "interrupt-cells" is not required. If the pin is an
> > interrupt it will be passed as an GPIO.
>
> It is same as external interrupt case right?
>
> For eg:- Ethernet PHY case,
>
> interrupt-parent = <&irqc>;
> interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
>
> if you use GPIO, it will be like this right?
>
> interrupt-parent = <&pinctrl>;
> interrupts = <RZG2L_GPIO(1, 0) IRQ_TYPE_LEVEL_LOW>;

FYI,

Previously, I have tested ADV HPD interrupt with below changes while investigating [1]

interrupt-parent = <&pinctrl>;
interrupts = <RZG2L_GPIO(2, 1) IRQ_TYPE_EDGE_FALLING>;

[1] https://git.kernel.org/pub/scm/linux/kernel/git/next/linux-next.git/commit/?h=next-20220512&id=04b19d32213654e54ec819b6ac033360f1551902

>
> Cheers,
> Biju
>
>
>
>
>
>
> >
> > @Geert - your thoughts ?
> >
> > Cheers,
> > Prabhakar
\
 
 \ /
  Last update: 2022-05-13 08:13    [W:0.085 / U:0.928 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site