Messages in this thread |  | | Date | Sat, 12 Mar 2022 17:09:54 +0900 | Subject | Re: [PATCH v0] pata_parport: add driver (PARIDE replacement) | From | Damien Le Moal <> |
| |
On 3/12/22 03:55, Ondrej Zary wrote: > On Friday 11 March 2022 00:59:20 Damien Le Moal wrote: >> On 3/11/22 06:28, Ondrej Zary wrote: >>> Add pata_parport (PARIDE replacement) core libata driver. >>> >>> The original paride protocol modules are used for now so allow them to >>> be compiled without old PARIDE core. >>> >>> Signed-off-by: Ondrej Zary <linux@zary.sk> >>> --- >>> drivers/Makefile | 2 +- >>> drivers/ata/Kconfig | 22 + >>> drivers/ata/Makefile | 2 + >>> drivers/ata/parport/Makefile | 3 + >>> drivers/ata/parport/pata_parport.c | 805 +++++++++++++++++++++++++++++ >>> drivers/ata/parport/pata_parport.h | 108 ++++ >>> drivers/block/paride/Kconfig | 32 +- >>> drivers/block/paride/paride.h | 5 + >>> 8 files changed, 962 insertions(+), 17 deletions(-) >>> create mode 100644 drivers/ata/parport/Makefile >>> create mode 100644 drivers/ata/parport/pata_parport.c >>> create mode 100644 drivers/ata/parport/pata_parport.h >>> >>> diff --git a/drivers/Makefile b/drivers/Makefile >>> index a110338c860c..8ec515f3614e 100644 >>> --- a/drivers/Makefile >>> +++ b/drivers/Makefile >>> @@ -98,7 +98,7 @@ obj-$(CONFIG_DIO) += dio/ >>> obj-$(CONFIG_SBUS) += sbus/ >>> obj-$(CONFIG_ZORRO) += zorro/ >>> obj-$(CONFIG_ATA_OVER_ETH) += block/aoe/ >>> -obj-$(CONFIG_PARIDE) += block/paride/ >>> +obj-y += block/paride/ >>> obj-$(CONFIG_TC) += tc/ >>> obj-$(CONFIG_USB_PHY) += usb/ >>> obj-$(CONFIG_USB) += usb/ >>> diff --git a/drivers/ata/Kconfig b/drivers/ata/Kconfig >>> index e5641e6c52ee..671c27b77a48 100644 >>> --- a/drivers/ata/Kconfig >>> +++ b/drivers/ata/Kconfig >>> @@ -1161,6 +1161,28 @@ config PATA_WINBOND_VLB >>> Support for the Winbond W83759A controller on Vesa Local Bus >>> systems. >>> >>> +config PATA_PARPORT >>> + tristate "Parallel port IDE device support" >>> + depends on PARPORT_PC && PARIDE=n >> >> This is very confusing. The change above this one switch paride >> compilation to be unconditional, regardless of CONFIG_PARIDE value, but >> here, you have the dependency to PARIDE=n. I do not understand... Please >> clarify. > > pata_parport will use existing paride protocol modules. So the paride/ directory must be processed to compile the protocol modules (if they're enabled) even if paride is not enabled. > > pata_parport and paride are mutually exclusive because the binary protocol modules are incompatible (the struct pi_adapter is different).
So if both CONFIG_PARIDE and CONFIG_PATA_PARPORT are disabled, there should be no need to compile the core PARIDE code under block/. You should have something like:
In drivers/Makefile:
-obj-$(CONFIG_PARIDE) += block/paride/ +obj-$(CONFIG_PARIDE_CORE) += block/paride/
And then have CONFIG_PARIDE and CONFIG_PATA_PARPORT select PARIDE_CORE, with CONFIG_PARIDE and CONFIG_PATA_PARPORT being mutually exclusive (using "depends on" as you did).
Here, I am assuming that block/paride is the core code used by both PARIDE and PATA_PARPORT. Not sure what PARPORT_PC does nor what its dependency on block/paride code is.
-- Damien Le Moal Western Digital Research
|  |