[lkml]   [2021]   [Jul]   [28]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
Messages in this thread
Subject[PATCH v10 0/3] media: imx: add support for imx8mq MIPI RX

This patch series adds a driver for the i.MX8MQ CSI MIPI receiver / controller.

It includes the driver, the dt-bindings and the DT addition to the SoC dtsi.
I test it using libcamera. Thanks to Laurent who helped a lot. I'm happy for
any feedback,


revision history
v10: (thank you Dafna)
* improve send_level documentation.
* add some comments to 0x180 and 0x184
* after re-reading I could eliminate the unneeded setting of 0x184 (ignored
by setting 0x180 to 1).

v9: (thank you Laurent)
* improve getting the esc clock rate for hs_settle

v8: (thank you Laurent)
* calculate hs_settle for any clk rate and mode
* add reviewed-by tag

v7: (thank you Laurent and Rob)
* fix the binding example (include the reset driver)
* use pm_runtime_resume_and_get()
* fix some logic in init_cfg()
* add some useful code comments and fix minor bits found by Laurent in v6

v6: (thank you Laurent and Rob)
* add reviewed-by tag to binding
* statically allocate clk_bulk_data
* fix how the hs_settle value is applied
* remove s_power calls
* remove the link_setup() callback implementation and make the link immutable
* more cleanups according to Laurents' review from v5

v5: (thank you Laurent)
* fix reset usage by using the already supported reset controller driver
* remove clko2 (totally unrelated clock / had been included by accident)
* rename pxl clock to ui

v4: (thank you Rob and Marco)
* create fsl,mipi-phy-gpr custom dt property instead of confusing "phy"
* add imx8mq-specific compatibile to imx8mq.dtsi for future use

v3: (thank you, Rob and Laurent)
among minor other things according to v2 review, changes include:
* better describe the clocks
* rename DT property "phy-reset" to "reset" and "phy-gpr" to "phy"

v2: (thank you, Dan and Guido)
among fixes according to v1 reviews, changes include:
* remove status property from dt-bindings example
* define a few bits in order to have less magic values
* use "imx8mq_mipi_csi_" as local function prefix
* read DT properties only during probe()
* remove dead code (log_status)
* add imx8mq_mipi_csi_release_icc()
* fix imx8mq_mipi_csi_init_icc()


Martin Kepplinger (3):
dt-bindings: media: document the nxp,imx8mq-mipi-csi2 receiver phy and
media: imx: add a driver for i.MX8MQ mipi csi rx phy and controller
arm64: dts: imx8mq: add mipi csi phy and csi bridge descriptions

.../bindings/media/nxp,imx8mq-mipi-csi2.yaml | 174 +++
arch/arm64/boot/dts/freescale/imx8mq.dtsi | 104 ++
drivers/staging/media/imx/Makefile | 1 +
drivers/staging/media/imx/imx8mq-mipi-csi2.c | 991 ++++++++++++++++++
4 files changed, 1270 insertions(+)
create mode 100644 Documentation/devicetree/bindings/media/nxp,imx8mq-mipi-csi2.yaml
create mode 100644 drivers/staging/media/imx/imx8mq-mipi-csi2.c


 \ /
  Last update: 2021-07-28 11:14    [W:0.091 / U:0.468 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site