lkml.org 
[lkml]   [2021]   [Mar]   [22]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH 5.10 109/157] regulator: pca9450: Add SD_VSEL GPIO for LDO5
Date
From: Frieder Schrempf <frieder.schrempf@kontron.de>

[ Upstream commit 8c67a11bae889f51fe5054364c3c789dfae3ad73 ]

LDO5 has two separate control registers. LDO5CTRL_L is used if the
input signal SD_VSEL is low and LDO5CTRL_H if it is high.
The current driver implementation only uses LDO5CTRL_H. To make this
work on boards that have SD_VSEL connected to a GPIO, we add support
for specifying an optional GPIO and setting it to high at probe time.

In the future we might also want to add support for boards that have
SD_VSEL set to a fixed low level. In this case we need to change the
driver to be able to use the LDO5CTRL_L register.

Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Link: https://lore.kernel.org/r/20210211105534.38972-1-frieder.schrempf@kontron.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
drivers/regulator/pca9450-regulator.c | 14 ++++++++++++++
1 file changed, 14 insertions(+)

diff --git a/drivers/regulator/pca9450-regulator.c b/drivers/regulator/pca9450-regulator.c
index cb29421d745a..1bba8fdcb7b7 100644
--- a/drivers/regulator/pca9450-regulator.c
+++ b/drivers/regulator/pca9450-regulator.c
@@ -5,6 +5,7 @@
*/

#include <linux/err.h>
+#include <linux/gpio/consumer.h>
#include <linux/i2c.h>
#include <linux/interrupt.h>
#include <linux/kernel.h>
@@ -32,6 +33,7 @@ struct pca9450_regulator_desc {
struct pca9450 {
struct device *dev;
struct regmap *regmap;
+ struct gpio_desc *sd_vsel_gpio;
enum pca9450_chip_type type;
unsigned int rcnt;
int irq;
@@ -795,6 +797,18 @@ static int pca9450_i2c_probe(struct i2c_client *i2c,
return ret;
}

+ /*
+ * The driver uses the LDO5CTRL_H register to control the LDO5 regulator.
+ * This is only valid if the SD_VSEL input of the PMIC is high. Let's
+ * check if the pin is available as GPIO and set it to high.
+ */
+ pca9450->sd_vsel_gpio = gpiod_get_optional(pca9450->dev, "sd-vsel", GPIOD_OUT_HIGH);
+
+ if (IS_ERR(pca9450->sd_vsel_gpio)) {
+ dev_err(&i2c->dev, "Failed to get SD_VSEL GPIO\n");
+ return ret;
+ }
+
dev_info(&i2c->dev, "%s probed.\n",
type == PCA9450_TYPE_PCA9450A ? "pca9450a" : "pca9450bc");

--
2.30.1


\
 
 \ /
  Last update: 2021-03-22 14:10    [W:0.525 / U:0.244 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site