lkml.org 
[lkml]   [2021]   [Feb]   [21]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
Date
From
SubjectRe: [PATCH 09/16] media: i2c: rdacm21: Re-work OV10640 initialization
Hi Jacopo,

Thank you for the patch.

On Tue, Feb 16, 2021 at 06:41:39PM +0100, Jacopo Mondi wrote:
> The OV10640 image sensor reset and powerdown on signals are controlled

s/ on//

> by the embedded OV490 ISP. The current reset procedure does not respect
> the 1 millisecond power-up delay and releases the reset signal before
> the powerdown one.
>
> Fix the OV10640 power up sequence by releasing the powerdown signal,
> waiting the mandatory 1 millisecond power up delay and then releasing
> the reset signal. The reset delay is not characterized in the chip
> manual if not as "255 XVCLK + initialization". Wait for at least 3
> milliseconds to guarantee the SCCB bus is available.
>
> This commit fixes a sporadic start-up error triggered by a failure to
> read the OV10640 chip ID:
> rdacm21 8-0054: OV10640 ID mismatch: (0x01)
>
> Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
> ---
> drivers/media/i2c/rdacm21.c | 6 ++++--
> 1 file changed, 4 insertions(+), 2 deletions(-)
>
> diff --git a/drivers/media/i2c/rdacm21.c b/drivers/media/i2c/rdacm21.c
> index b22a2ca5340b..c420a6b96879 100644
> --- a/drivers/media/i2c/rdacm21.c
> +++ b/drivers/media/i2c/rdacm21.c
> @@ -333,13 +333,15 @@ static int ov10640_initialize(struct rdacm21_device *dev)
> {
> u8 val;
>
> - /* Power-up OV10640 by setting RESETB and PWDNB pins high. */
> + /* Power-up OV10640 by setting PWDNB and RESETB pins high. */
> ov490_write_reg(dev, OV490_GPIO_SEL0, OV490_GPIO0);
> ov490_write_reg(dev, OV490_GPIO_SEL1, OV490_SPWDN0);
> ov490_write_reg(dev, OV490_GPIO_DIRECTION0, OV490_GPIO0);
> ov490_write_reg(dev, OV490_GPIO_DIRECTION1, OV490_SPWDN0);
> - ov490_write_reg(dev, OV490_GPIO_OUTPUT_VALUE0, OV490_GPIO0);
> +
> ov490_write_reg(dev, OV490_GPIO_OUTPUT_VALUE0, OV490_SPWDN0);

Shouldn't this be OV490_GPIO_OUTPUT_VALUE1 ?

> + usleep_range(1500, 3000);
> + ov490_write_reg(dev, OV490_GPIO_OUTPUT_VALUE0, OV490_GPIO0);

I'm a bit puzzled by why this patch would improve the ID read issue,
given that it sets GPIO0 to 1, then sets GPIO0 to 1, compared to
previously setting GPIO0 to 1 following by setting GPIO0 to 1 :-) Maybe
it's the additional delay ? In any case, it would probably be a good
idea to perform additional tests after fixing this.

> usleep_range(3000, 5000);
>
> /* Read OV10640 ID to test communications. */

--
Regards,

Laurent Pinchart

\
 
 \ /
  Last update: 2021-02-22 02:29    [W:0.318 / U:5.188 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site