lkml.org 
[lkml]   [2021]   [Jan]   [26]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
Date
From
SubjectRe: [PATCH v3 2/2] counter: add GPIO based pulse counters
Hi Jonathan,

On Sun, Jan 24, 2021 at 02:47:37PM +0000, Jonathan Cameron wrote:
> On Fri, 22 Jan 2021 12:24:34 +0100
> Oleksij Rempel <o.rempel@pengutronix.de> wrote:
>
> > Add simple GPIO base pulse counter. This device is used to measure
> > rotation speed of some agricultural devices, so no high frequency on the
> > counter pin is expected.
> >
> > The maximal measurement frequency depends on the CPU and system load. On
> > the idle iMX6S I was able to measure up to 20kHz without count drops.
> >
> > Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
>
> Hi Oleksij,
>
> A few comments inline.
>
> Thanks,
>
> Jonathan
>
> > ---
> > drivers/counter/Kconfig | 9 ++
> > drivers/counter/Makefile | 1 +
> > drivers/counter/gpio-pulse-cnt.c | 244 +++++++++++++++++++++++++++++++
> > 3 files changed, 254 insertions(+)
> > create mode 100644 drivers/counter/gpio-pulse-cnt.c
> >
> > diff --git a/drivers/counter/Kconfig b/drivers/counter/Kconfig
> > index 2de53ab0dd25..9ad1d9d49dd1 100644
> > --- a/drivers/counter/Kconfig
> > +++ b/drivers/counter/Kconfig
> > @@ -29,6 +29,15 @@ config 104_QUAD_8
> > The base port addresses for the devices may be configured via the base
> > array module parameter.
> >
> > +config GPIO_PULSE_CNT
> > + tristate "GPIO pulse counter driver"
> > + depends on GPIOLIB
> > + help
> > + Select this option to enable GPIO pulse counter driver.
> > +
> > + To compile this driver as a module, choose M here: the
> > + module will be called gpio-pulse-cnt.
> > +
> > config STM32_TIMER_CNT
> > tristate "STM32 Timer encoder counter driver"
> > depends on MFD_STM32_TIMERS || COMPILE_TEST
> > diff --git a/drivers/counter/Makefile b/drivers/counter/Makefile
> > index 0a393f71e481..6a5c3fc6f2a0 100644
> > --- a/drivers/counter/Makefile
> > +++ b/drivers/counter/Makefile
> > @@ -6,6 +6,7 @@
> > obj-$(CONFIG_COUNTER) += counter.o
> >
> > obj-$(CONFIG_104_QUAD_8) += 104-quad-8.o
> > +obj-$(CONFIG_GPIO_PULSE_CNT) += gpio-pulse-cnt.o
> > obj-$(CONFIG_STM32_TIMER_CNT) += stm32-timer-cnt.o
> > obj-$(CONFIG_STM32_LPTIMER_CNT) += stm32-lptimer-cnt.o
> > obj-$(CONFIG_TI_EQEP) += ti-eqep.o
> > diff --git a/drivers/counter/gpio-pulse-cnt.c b/drivers/counter/gpio-pulse-cnt.c
> > new file mode 100644
> > index 000000000000..9454345c77ad
> > --- /dev/null
> > +++ b/drivers/counter/gpio-pulse-cnt.c
> > @@ -0,0 +1,244 @@
> > +// SPDX-License-Identifier: GPL-2.0
> > +/*
> > + * Copyright (c) 2021 Pengutronix, Oleksij Rempel <kernel@pengutronix.de>
> > + */
> > +
> > +#include <linux/counter.h>
> > +#include <linux/gpio/consumer.h>
> > +#include <linux/interrupt.h>
> > +#include <linux/module.h>
> > +#include <linux/of_device.h>
> why of_device.h? Probably want mod_devicetable.h instead.

done

> > +#include <linux/platform_device.h>
> > +
> > +#define GPIO_PULSE_NAME "gpio-pulse-counter"
> > +
> > +struct gpio_pulse_priv {
> > + struct counter_device counter;
> > + struct gpio_desc *gpio;
> > + int irq;
> > + bool enabled;
> > + atomic_t count;
> > +};
> > +
> > +static irqreturn_t gpio_pulse_irq_isr(int irq, void *dev_id)
> > +{
> > + struct gpio_pulse_priv *priv = dev_id;
> > +
> > + if (!priv->enabled)
> > + return IRQ_NONE;
> > +
> > + atomic_inc(&priv->count);
> > +
> > + return IRQ_HANDLED;
> > +}
> > +
> > +static ssize_t gpio_pulse_count_enable_read(struct counter_device *counter,
> > + struct counter_count *count,
> > + void *private, char *buf)
> > +{
> > + struct gpio_pulse_priv *priv = counter->priv;
> > +
> > + return sysfs_emit(buf, "%d\n", priv->enabled);
> > +}
> > +
> > +static ssize_t gpio_pulse_count_enable_write(struct counter_device *counter,
> > + struct counter_count *count,
> > + void *private,
> > + const char *buf, size_t len)
> > +{
> > + struct gpio_pulse_priv *priv = counter->priv;
> > + bool enable;
> > + ssize_t ret;
> > +
> > + ret = kstrtobool(buf, &enable);
> > + if (ret)
> > + return ret;
> > +
> > + if (priv->enabled == enable)
> > + return len;
> > +
> > + priv->enabled = enable;
> > +
> > + if (enable)
> > + enable_irq(priv->irq);
> > + else
> > + disable_irq(priv->irq);
>
> As pointed out by Ahmad, this is all racy.
> Personally I'd just let the race happen, and don't
> bother with the priv->enabled at all.

yes, i forgot about existence of IRQ_NOAUTOEN

> We aren't going to be dealing with shared interrupts
> here so if we get a race, it's between userspace write
> getting through to enable / disable the interrupt and
> a pulse coming in. The userspace part is so unpredictable on
> timing etc the race isn't pretty meaningless (you might count
> one extra, but then if userspace took a bit longer you might
> do that anyway).
>
>
> > +
> > + return len;
> > +}
> > +
> > +static const struct counter_count_ext gpio_pulse_count_ext[] = {
> > + {
> > + .name = "enable",
> > + .read = gpio_pulse_count_enable_read,
> > + .write = gpio_pulse_count_enable_write,
> > + },
> > +};
> > +
> > +static enum counter_synapse_action gpio_pulse_synapse_actions[] = {
> > + COUNTER_SYNAPSE_ACTION_RISING_EDGE,
> > +};
> > +
> > +static int gpio_pulse_action_get(struct counter_device *counter,
> > + struct counter_count *count,
> > + struct counter_synapse *synapse,
> > + size_t *action)
> > +{
> > + *action = COUNTER_SYNAPSE_ACTION_RISING_EDGE;
> > +
> > + return 0;
> > +}
> > +
> > +static int gpio_pulse_count_read(struct counter_device *counter,
> > + struct counter_count *count,
> > + unsigned long *val)
> > +{
> > + struct gpio_pulse_priv *priv = counter->priv;
> > +
> > + *val = atomic_read(&priv->count);
> > +
> > + return 0;
> > +}
> > +
> > +static int gpio_pulse_count_write(struct counter_device *counter,
> > + struct counter_count *count,
> > + const unsigned long val)
> > +{
> > + struct gpio_pulse_priv *priv = counter->priv;
> > +
> > + atomic_set(&priv->count, val);
> > +
> > + return 0;
> > +}
> > +
> > +static int gpio_pulse_count_function_get(struct counter_device *counter,
> > + struct counter_count *count,
> > + size_t *function)
> > +{
> > + *function = COUNTER_COUNT_FUNCTION_INCREASE;
> > +
> > + return 0;
> > +}
> > +
> > +static int gpio_pulse_count_signal_read(struct counter_device *counter,
> > + struct counter_signal *signal,
> > + enum counter_signal_value *val)
> > +{
> > + struct gpio_pulse_priv *priv = counter->priv;
> > + int ret;
> > +
> > + ret = gpiod_get_value(priv->gpio);
> > + if (ret < 0)
> > + return ret;
> > +
> > + *val = ret ? COUNTER_SIGNAL_HIGH : COUNTER_SIGNAL_LOW;
> > +
> > + return 0;
> > +}
> > +
> > +static const struct counter_ops gpio_pulse_cnt_ops = {
> > + .action_get = gpio_pulse_action_get,
> > + .count_read = gpio_pulse_count_read,
> > + .count_write = gpio_pulse_count_write,
> > + .function_get = gpio_pulse_count_function_get,
> > + .signal_read = gpio_pulse_count_signal_read,
> > +};
> > +
> > +static struct counter_signal gpio_pulse_signals[] = {
> > + {
> > + .id = 0,
> > + .name = "Channel 0 signal",
> > + },
> > +};
> > +
> > +static struct counter_synapse gpio_pulse_count_synapses[] = {
> > + {
> > + .actions_list = gpio_pulse_synapse_actions,
> > + .num_actions = ARRAY_SIZE(gpio_pulse_synapse_actions),
> > + .signal = &gpio_pulse_signals[0]
> > + },
> > +};
> > +
> > +static enum counter_count_function gpio_pulse_count_functions[] = {
> > + COUNTER_COUNT_FUNCTION_INCREASE,
> > +};
> > +
> > +static struct counter_count gpio_pulse_counts[] = {
> > + {
> > + .id = 0,
> > + .name = "Channel 1 Count",
> > + .functions_list = gpio_pulse_count_functions,
> > + .num_functions = ARRAY_SIZE(gpio_pulse_count_functions),
> > + .synapses = gpio_pulse_count_synapses,
> > + .num_synapses = ARRAY_SIZE(gpio_pulse_count_synapses),
> > + .ext = gpio_pulse_count_ext,
> > + .num_ext = ARRAY_SIZE(gpio_pulse_count_ext),
> > + },
> > +};
> > +
> > +static int gpio_pulse_cnt_probe(struct platform_device *pdev)
> > +{
> > + struct device *dev = &pdev->dev;
> > + struct gpio_pulse_priv *priv;
> > + int ret;
> > +
> > + priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
> > + if (!priv)
> > + return -ENOMEM;
> > +
> > + if (gpiod_count(dev, NULL) != 1) {
> > + dev_err(dev, "Error, need exactly 1 gpio for device\n");
> > + return -EINVAL;
> > + }
> > +
> > + priv->gpio = devm_gpiod_get(dev, NULL, GPIOD_IN);
> > + if (IS_ERR(priv->gpio))
> > + return dev_err_probe(dev, PTR_ERR(priv->gpio), "failed to get gpio\n");
>
> My gut feeling here is that it probably makes sense to drop
> the direct read of the signal level, and hence allow the driver
> to be provided with an interrupt instead of a gpio.
>
> Afterall, not all gpio lines are interrupt capable.

Hm, .. I need to be able to sense GPIO level for diagnostic interface.
So, in this case i'll need to get irq and gpio separately

> > +
> > + priv->irq = gpiod_to_irq(priv->gpio);
> > + if (priv->irq < 0) {
> > + dev_err(dev, "failed to map GPIO to IRQ: %d\n", priv->irq);
> > + return priv->irq;
> > + }
> > +
> > + priv->counter.name = dev_name(dev);
> > + priv->counter.parent = dev;
> > + priv->counter.ops = &gpio_pulse_cnt_ops;
> > + priv->counter.counts = gpio_pulse_counts;
> > + priv->counter.num_counts = ARRAY_SIZE(gpio_pulse_counts);
> > + priv->counter.signals = gpio_pulse_signals;
> > + priv->counter.num_signals = ARRAY_SIZE(gpio_pulse_signals);
> > + priv->counter.priv = priv;
> > +
> > + ret = devm_request_irq(dev, priv->irq, gpio_pulse_irq_isr,
> > + IRQF_TRIGGER_RISING | IRQF_NO_THREAD,
> > + GPIO_PULSE_NAME, priv);
> > + if (ret)
> > + return ret;
> > +
> > + disable_irq(priv->irq);
>
> Race condition here (messy at least) that we can close down.

ACK

> Note there is ongoing work to try and do this in a nice generic
> fashion, but in the meantime call
>
> irq_set_status_flags(priv->irq, IRQ_NOAUTOEN);

^^ yes! this is what i was seeking! Thx.

> before the devm_request_irq()
>
> https://lore.kernel.org/lkml/20210107223926.35284-2-song.bao.hua@hisilicon.com/

Nice!

> There are a lot of cases that series will tidy up, but let us do the best
> we can in the meantime!
>
> > +
> > + platform_set_drvdata(pdev, priv);
> > +
> > + return devm_counter_register(dev, &priv->counter);
> > +}
> > +
> > +static const struct of_device_id gpio_pulse_cnt_of_match[] = {
> > + { .compatible = "virtual,gpio-pulse-counter", },
> > + {}
> > +};
> > +MODULE_DEVICE_TABLE(of, gpio_pulse_cnt_of_match);
> > +
> > +static struct platform_driver gpio_pulse_cnt_driver = {
> > + .probe = gpio_pulse_cnt_probe,
> > + .driver = {
> > + .name = GPIO_PULSE_NAME,
> > + .of_match_table = gpio_pulse_cnt_of_match,
> > + },
> > +};
> > +module_platform_driver(gpio_pulse_cnt_driver);
> > +
> > +MODULE_ALIAS("platform:gpio-pulse-counter");
> > +MODULE_AUTHOR("Oleksij Rempel <o.rempel@pengutronix.de>");
> > +MODULE_DESCRIPTION("GPIO pulse counter driver");
> > +MODULE_LICENSE("GPL v2");

Thank you.

Regards,
Oleksij
--
Pengutronix e.K. | |
Steuerwalder Str. 21 | http://www.pengutronix.de/ |
31137 Hildesheim, Germany | Phone: +49-5121-206917-0 |
Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |
\
 
 \ /
  Last update: 2021-01-26 18:47    [W:0.195 / U:1.140 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site