lkml.org 
[lkml]   [2021]   [Jan]   [22]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH v3 2/2] counter: add GPIO based pulse counters
From
Date
Hello,

On 22.01.21 12:24, Oleksij Rempel wrote:
> Add simple GPIO base pulse counter. This device is used to measure
> rotation speed of some agricultural devices, so no high frequency on the
> counter pin is expected.
>
> The maximal measurement frequency depends on the CPU and system load. On
> the idle iMX6S I was able to measure up to 20kHz without count drops.
>
> Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
> ---
> drivers/counter/Kconfig | 9 ++
> drivers/counter/Makefile | 1 +
> drivers/counter/gpio-pulse-cnt.c | 244 +++++++++++++++++++++++++++++++
> 3 files changed, 254 insertions(+)
> create mode 100644 drivers/counter/gpio-pulse-cnt.c
>
> diff --git a/drivers/counter/Kconfig b/drivers/counter/Kconfig
> index 2de53ab0dd25..9ad1d9d49dd1 100644
> --- a/drivers/counter/Kconfig
> +++ b/drivers/counter/Kconfig
> @@ -29,6 +29,15 @@ config 104_QUAD_8
> The base port addresses for the devices may be configured via the base
> array module parameter.
>
> +config GPIO_PULSE_CNT
> + tristate "GPIO pulse counter driver"
> + depends on GPIOLIB
> + help
> + Select this option to enable GPIO pulse counter driver.
> +
> + To compile this driver as a module, choose M here: the
> + module will be called gpio-pulse-cnt.
> +
> config STM32_TIMER_CNT
> tristate "STM32 Timer encoder counter driver"
> depends on MFD_STM32_TIMERS || COMPILE_TEST
> diff --git a/drivers/counter/Makefile b/drivers/counter/Makefile
> index 0a393f71e481..6a5c3fc6f2a0 100644
> --- a/drivers/counter/Makefile
> +++ b/drivers/counter/Makefile
> @@ -6,6 +6,7 @@
> obj-$(CONFIG_COUNTER) += counter.o
>
> obj-$(CONFIG_104_QUAD_8) += 104-quad-8.o
> +obj-$(CONFIG_GPIO_PULSE_CNT) += gpio-pulse-cnt.o
> obj-$(CONFIG_STM32_TIMER_CNT) += stm32-timer-cnt.o
> obj-$(CONFIG_STM32_LPTIMER_CNT) += stm32-lptimer-cnt.o
> obj-$(CONFIG_TI_EQEP) += ti-eqep.o
> diff --git a/drivers/counter/gpio-pulse-cnt.c b/drivers/counter/gpio-pulse-cnt.c
> new file mode 100644
> index 000000000000..9454345c77ad
> --- /dev/null
> +++ b/drivers/counter/gpio-pulse-cnt.c
> @@ -0,0 +1,244 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Copyright (c) 2021 Pengutronix, Oleksij Rempel <kernel@pengutronix.de>
> + */
> +
> +#include <linux/counter.h>
> +#include <linux/gpio/consumer.h>
> +#include <linux/interrupt.h>
> +#include <linux/module.h>
> +#include <linux/of_device.h>
> +#include <linux/platform_device.h>
> +
> +#define GPIO_PULSE_NAME "gpio-pulse-counter"
> +
> +struct gpio_pulse_priv {
> + struct counter_device counter;
> + struct gpio_desc *gpio;
> + int irq;
> + bool enabled;
> + atomic_t count;
> +};
> +
> +static irqreturn_t gpio_pulse_irq_isr(int irq, void *dev_id)
> +{
> + struct gpio_pulse_priv *priv = dev_id;
> +
> + if (!priv->enabled)

Sorry, didn't look too closely first time.

- User sets ->enable = 0
- IRQ raised before disabling
- you return IRQ_NONE, kernel logs a spurious IRQ

I'd say that's a bug. Instead:

- Can we ask whether an irq is enabled? If so, you can drop ->enabled
- Otherwise, you should set ->enabled while irqs are off. So after disable
and before enable. You also need READ_ONCE/WRITE_ONCE.

With this addressed, for the non-counter-framework-specific parts:
Reviewed-by: Ahmad Fatoum <a.fatoum@pengutronix.de>

> + return IRQ_NONE;
> +
> + atomic_inc(&priv->count);
> +
> + return IRQ_HANDLED;
> +}
> +
> +static ssize_t gpio_pulse_count_enable_read(struct counter_device *counter,
> + struct counter_count *count,
> + void *private, char *buf)
> +{
> + struct gpio_pulse_priv *priv = counter->priv;
> +
> + return sysfs_emit(buf, "%d\n", priv->enabled);
> +}
> +
> +static ssize_t gpio_pulse_count_enable_write(struct counter_device *counter,
> + struct counter_count *count,
> + void *private,
> + const char *buf, size_t len)
> +{
> + struct gpio_pulse_priv *priv = counter->priv;
> + bool enable;
> + ssize_t ret;
> +
> + ret = kstrtobool(buf, &enable);
> + if (ret)
> + return ret;
> +
> + if (priv->enabled == enable)
> + return len;
> +
> + priv->enabled = enable;
> +
> + if (enable)
> + enable_irq(priv->irq);
> + else
> + disable_irq(priv->irq);
> +
> + return len;
> +}
> +
> +static const struct counter_count_ext gpio_pulse_count_ext[] = {
> + {
> + .name = "enable",
> + .read = gpio_pulse_count_enable_read,
> + .write = gpio_pulse_count_enable_write,
> + },
> +};
> +
> +static enum counter_synapse_action gpio_pulse_synapse_actions[] = {
> + COUNTER_SYNAPSE_ACTION_RISING_EDGE,
> +};
> +
> +static int gpio_pulse_action_get(struct counter_device *counter,
> + struct counter_count *count,
> + struct counter_synapse *synapse,
> + size_t *action)
> +{
> + *action = COUNTER_SYNAPSE_ACTION_RISING_EDGE;
> +
> + return 0;
> +}
> +
> +static int gpio_pulse_count_read(struct counter_device *counter,
> + struct counter_count *count,
> + unsigned long *val)
> +{
> + struct gpio_pulse_priv *priv = counter->priv;
> +
> + *val = atomic_read(&priv->count);
> +
> + return 0;
> +}
> +
> +static int gpio_pulse_count_write(struct counter_device *counter,
> + struct counter_count *count,
> + const unsigned long val)
> +{
> + struct gpio_pulse_priv *priv = counter->priv;
> +
> + atomic_set(&priv->count, val);
> +
> + return 0;
> +}
> +
> +static int gpio_pulse_count_function_get(struct counter_device *counter,
> + struct counter_count *count,
> + size_t *function)
> +{
> + *function = COUNTER_COUNT_FUNCTION_INCREASE;
> +
> + return 0;
> +}
> +
> +static int gpio_pulse_count_signal_read(struct counter_device *counter,
> + struct counter_signal *signal,
> + enum counter_signal_value *val)
> +{
> + struct gpio_pulse_priv *priv = counter->priv;
> + int ret;
> +
> + ret = gpiod_get_value(priv->gpio);
> + if (ret < 0)
> + return ret;
> +
> + *val = ret ? COUNTER_SIGNAL_HIGH : COUNTER_SIGNAL_LOW;
> +
> + return 0;
> +}
> +
> +static const struct counter_ops gpio_pulse_cnt_ops = {
> + .action_get = gpio_pulse_action_get,
> + .count_read = gpio_pulse_count_read,
> + .count_write = gpio_pulse_count_write,
> + .function_get = gpio_pulse_count_function_get,
> + .signal_read = gpio_pulse_count_signal_read,
> +};
> +
> +static struct counter_signal gpio_pulse_signals[] = {
> + {
> + .id = 0,
> + .name = "Channel 0 signal",
> + },
> +};
> +
> +static struct counter_synapse gpio_pulse_count_synapses[] = {
> + {
> + .actions_list = gpio_pulse_synapse_actions,
> + .num_actions = ARRAY_SIZE(gpio_pulse_synapse_actions),
> + .signal = &gpio_pulse_signals[0]
> + },
> +};
> +
> +static enum counter_count_function gpio_pulse_count_functions[] = {
> + COUNTER_COUNT_FUNCTION_INCREASE,
> +};
> +
> +static struct counter_count gpio_pulse_counts[] = {
> + {
> + .id = 0,
> + .name = "Channel 1 Count",
> + .functions_list = gpio_pulse_count_functions,
> + .num_functions = ARRAY_SIZE(gpio_pulse_count_functions),
> + .synapses = gpio_pulse_count_synapses,
> + .num_synapses = ARRAY_SIZE(gpio_pulse_count_synapses),
> + .ext = gpio_pulse_count_ext,
> + .num_ext = ARRAY_SIZE(gpio_pulse_count_ext),
> + },
> +};
> +
> +static int gpio_pulse_cnt_probe(struct platform_device *pdev)
> +{
> + struct device *dev = &pdev->dev;
> + struct gpio_pulse_priv *priv;
> + int ret;
> +
> + priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
> + if (!priv)
> + return -ENOMEM;
> +
> + if (gpiod_count(dev, NULL) != 1) {
> + dev_err(dev, "Error, need exactly 1 gpio for device\n");
> + return -EINVAL;
> + }
> +
> + priv->gpio = devm_gpiod_get(dev, NULL, GPIOD_IN);
> + if (IS_ERR(priv->gpio))
> + return dev_err_probe(dev, PTR_ERR(priv->gpio), "failed to get gpio\n");
> +
> + priv->irq = gpiod_to_irq(priv->gpio);
> + if (priv->irq < 0) {
> + dev_err(dev, "failed to map GPIO to IRQ: %d\n", priv->irq);
> + return priv->irq;
> + }
> +
> + priv->counter.name = dev_name(dev);
> + priv->counter.parent = dev;
> + priv->counter.ops = &gpio_pulse_cnt_ops;
> + priv->counter.counts = gpio_pulse_counts;
> + priv->counter.num_counts = ARRAY_SIZE(gpio_pulse_counts);
> + priv->counter.signals = gpio_pulse_signals;
> + priv->counter.num_signals = ARRAY_SIZE(gpio_pulse_signals);
> + priv->counter.priv = priv;
> +
> + ret = devm_request_irq(dev, priv->irq, gpio_pulse_irq_isr,
> + IRQF_TRIGGER_RISING | IRQF_NO_THREAD,
> + GPIO_PULSE_NAME, priv);
> + if (ret)
> + return ret;
> +
> + disable_irq(priv->irq);
> +
> + platform_set_drvdata(pdev, priv);
> +
> + return devm_counter_register(dev, &priv->counter);
> +}
> +
> +static const struct of_device_id gpio_pulse_cnt_of_match[] = {
> + { .compatible = "virtual,gpio-pulse-counter", },
> + {}
> +};
> +MODULE_DEVICE_TABLE(of, gpio_pulse_cnt_of_match);
> +
> +static struct platform_driver gpio_pulse_cnt_driver = {
> + .probe = gpio_pulse_cnt_probe,
> + .driver = {
> + .name = GPIO_PULSE_NAME,
> + .of_match_table = gpio_pulse_cnt_of_match,
> + },
> +};
> +module_platform_driver(gpio_pulse_cnt_driver);
> +
> +MODULE_ALIAS("platform:gpio-pulse-counter");
> +MODULE_AUTHOR("Oleksij Rempel <o.rempel@pengutronix.de>");
> +MODULE_DESCRIPTION("GPIO pulse counter driver");
> +MODULE_LICENSE("GPL v2");
>

--
Pengutronix e.K. | |
Steuerwalder Str. 21 | http://www.pengutronix.de/ |
31137 Hildesheim, Germany | Phone: +49-5121-206917-0 |
Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |

\
 
 \ /
  Last update: 2021-01-22 12:53    [W:0.081 / U:0.188 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site