lkml.org 
[lkml]   [2021]   [Jan]   [12]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH v2 1/2] arm64: dts: broadcom: clear the warnings caused by empty dma-ranges
From
Date


On 1/12/2021 12:40 PM, Arnd Bergmann wrote:
> On Tue, Jan 12, 2021 at 7:28 PM Ray Jui <ray.jui@broadcom.com> wrote:
>> On 2020-12-15 7:49 a.m., Arnd Bergmann wrote:
>>> On Tue, Dec 15, 2020 at 4:41 PM Florian Fainelli <f.fainelli@gmail.com> wrote:
>>>>
>>>> On 12/15/2020 5:19 AM, Bharat Gooty wrote:
>>>>> Since the IOMMU is disabled and DMA engine is on 32-bit bus, We can not
>>>>> give the complete DDR for the USB DMA.
>>>>> So restricting the usable DAM size to 4GB.
>>>>
>>>> Thanks, can you make this a proper patch submission along with a Fixes:
>>>> tag that is:
>>>>
>>>> Fixes: 2013a4b684b6 ("arm64: dts: broadcom: clear the warnings caused by
>>>> empty dma-ranges")
>>>
>>> Yes, that would be helpful, though I would appreciate a better description
>>> that explains what is actually going on: is it the device or the bus that
>>> has the 32-bit limitation, and if it is indeed a bug in the device, why do
>>> you pretend that this is a 64-bit device on a 32-bit bus instead (this
>>> could also use a comment in the dts file)?
>>>
>>> Arnd
>>>
>>
>> Sorry for the delay in reply. Bharat finally got time to do some
>> investigation to confirm the following:
>>
>> These USB controllers indeed can address 64-bit. However, on the bus
>> internally, only 40-bits are connected to the interconnect of CCN. As a
>> result, the 'dma-ranges' should be modified to address 40-bit in size.
>
> a 40-bit range is effectively the same as a 64-bit range though, so I
> think you'll still need a driver quirk if the device cannot use the whole 40
> bit addressing but is limited to 32 bits because of a bug in its dma engine.
>

Bharat can correct me if I'm wrong, but I don't think we have a bug in
the USB DMA engine that causes it can only address 32-bit. I believe we
can set dma-ranges size to 40-bit here.

The dma-range property is though required to be specified, instead of
leaving it as empty, with the use of IOMMU. That seems to be a v5.10
specific behavior as I described below.

Thanks,

Ray

>> We also have a somewhat related question, is it true that since v5.10,
>> defining of 'dma-ranges' on the bus node where its child device node has
>> implication of IOMMU usage (through 'iommus' or 'iommu-map') is now
>> mandatory? My understanding is that the 'dma-ranges' in this scheme will
>> define the IOVA address to system address mapping required by all
>> devices on that bus. Please help to confirm if my understanding is correct
>
> I have not actually seen that change. In general, you should always
> have a dma-ranges property in the parent of a DMA master, I think
> we just never enforced that and fall back to a 32-bit mask by default.
>
> Arnd
>
[unhandled content-type:application/pkcs7-signature]
\
 
 \ /
  Last update: 2021-01-12 23:11    [W:0.116 / U:2.752 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site