lkml.org 
[lkml]   [2021]   [Jan]   [10]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH 3/3] arm64: dts: rockchip: rk3328: Add Radxa ROCK Pi E
From
Date
Hi Chen-Yu,

Some comments, have a look if it is useful...

On 1/10/21 4:58 AM, Chen-Yu Tsai wrote:
> From: Chen-Yu Tsai <wens@csie.org>
>
> Radxa ROCK Pi E is a router oriented SBC based on Rockchip's RK3328 SoC.
> As the official wiki page puts it, "E for Ethernets".
>
> It features the RK3328 SoC, gigabit and fast Ethernet RJ45 ports, both
> directly served by Ethernet controllers in the SoC, a USB 3.0 host port,
> a power-only USB type-C port, a 3.5mm headphone jack for audio output,

> two LEDs, a 40-pin Raspberry Pi style GPIO header, and optional WiFi+BT
> and PoE header.
>
> The board comes in multiple configurations, differing in the amount of
> onboard RAM, the level of WiFi+BT (none, 802.11n 2.4GHz, or 802.11ac
> 2.4 GHz & 5 GHz), and whether PoE is supported or not. These variants
> can all share the same device tree.
>
> The USB 2.0 OTG controller is available on the 40-pin header. This is
> not enabled in the device tree, since it is possible to use it in a
> host-only configuration, or in OTG mode with an extra pin from the
> header as the ID pin.
>
> The device tree is based on the one of the Rock64, with various parts
> modified to match the ROCK Pi E, and some parts updated to newer styles,
> such as the gmac2io node's mdio sub-node.
>
> Add a new device tree file for the new board.
>
> Signed-off-by: Chen-Yu Tsai <wens@csie.org>
> ---
> arch/arm64/boot/dts/rockchip/Makefile | 1 +
> .../boot/dts/rockchip/rk3328-rock-pi-e.dts | 369 ++++++++++++++++++
> 2 files changed, 370 insertions(+)
> create mode 100644 arch/arm64/boot/dts/rockchip/rk3328-rock-pi-e.dts
>
> diff --git a/arch/arm64/boot/dts/rockchip/Makefile b/arch/arm64/boot/dts/rockchip/Makefile
> index 622d320ddd13..62d3abc17a24 100644
> --- a/arch/arm64/boot/dts/rockchip/Makefile
> +++ b/arch/arm64/boot/dts/rockchip/Makefile
> @@ -11,6 +11,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-a1.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-evb.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-nanopi-r2s.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-rock64.dtb
> +dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-rock-pi-e.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-roc-cc.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3368-evb-act8846.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3368-geekbox.dtb
> diff --git a/arch/arm64/boot/dts/rockchip/rk3328-rock-pi-e.dts b/arch/arm64/boot/dts/rockchip/rk3328-rock-pi-e.dts
> new file mode 100644
> index 000000000000..7818d2e8180c
> --- /dev/null
> +++ b/arch/arm64/boot/dts/rockchip/rk3328-rock-pi-e.dts
> @@ -0,0 +1,369 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * (C) Copyright 2020 Chen-Yu Tsai <wens@csie.org>
> + *
> + * Based on ./rk3328-rock64.dts, which is
> + *
> + * Copyright (c) 2017 PINE64
> + */
> +
> +/dts-v1/;
> +
> +#include <dt-bindings/leds/common.h>
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/pinctrl/rockchip.h>
> +#include "rk3328.dtsi"
> +
> +/ {
> + model = "Radxa ROCK Pi E";
> + compatible = "radxa,rockpi-e", "rockchip,rk3328";
> +
> + chosen {
> + stdout-path = "serial2:1500000n8";
> + };
> +
> + gmac_clkin: external-gmac-clock {
> + compatible = "fixed-clock";
> + clock-frequency = <125000000>;
> + clock-output-names = "gmac_clkin";
> + #clock-cells = <0>;
> + };
> +
> + leds {
> + compatible = "gpio-leds";
> + pinctrl-0 = <&led_pin>;
> + pinctrl-names = "default";
> +
> + led-0 {

> + /* schematic say green but the actual thing is blue */

In rockpie-v1.2-20200427-sch.pdf this led is already called "LED_BLUE",
so comment maybe not needed anymore?

> + color = <LED_COLOR_ID_BLUE>;
> + gpios = <&gpio3 RK_PA5 GPIO_ACTIVE_LOW>;
> + linux,default-trigger = "heartbeat";
> + };> + };
> +
> + vcc_sd: sdmmc-regulator {
> + compatible = "regulator-fixed";
> + gpio = <&gpio0 RK_PD6 GPIO_ACTIVE_LOW>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&sdmmc0m1_pin>;

> + regulator-boot-on;
> + regulator-name = "vcc_sd";

regulator-name above other regulator properties

regulator voltage missing
make things as complete as possible

from fixed-regulator.yaml:

description:
Any property defined as part of the core regulator binding, defined in
regulator.yaml, can also be used. However a fixed voltage regulator is
expected to have the regulator-min-microvolt and regulator-max-microvolt
to be the same.

> + vin-supply = <&vcc_io>;
> + };
> +

> + vcc_host_5v: vcc-host-5v-regulator {
> + compatible = "regulator-fixed";
> + gpio = <&gpio3 RK_PA7 GPIO_ACTIVE_HIGH>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&usb30_host_drv>;
> + enable-active-high;
> + regulator-name = "vcc_host_5v";

idem limits

> + regulator-always-on;
> + regulator-boot-on;
> + vin-supply = <&vcc_sys>;
> + };

For Heiko: ?? remove ??
usb3 has no support in mainline.
Regulators not in use are disabled.
For mainline this node has no use....

> +
> + vcc_sys: vcc-sys {
> + compatible = "regulator-fixed";
> + regulator-name = "vcc_sys";

> + regulator-always-on;
> + regulator-boot-on;

At the other regulators this is sort below the regulator limits.

> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + };
> +
> + vcc_wifi: vcc-wifi-regulator {
> + compatible = "regulator-fixed";
> + gpio = <&gpio0 RK_PA0 GPIO_ACTIVE_LOW>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&wifi_en>;
> + regulator-name = "vcc_wifi";

idem limits

> + regulator-always-on;
> + regulator-boot-on;
> + vin-supply = <&vcc_io>;
> + };
> +};
> +
> +&analog_sound {
> + status = "okay";
> +};
> +
> +&codec {
> + status = "okay";
> +};
> +
> +&cpu0 {
> + cpu-supply = <&vdd_arm>;
> +};
> +
> +&cpu1 {
> + cpu-supply = <&vdd_arm>;
> +};
> +
> +&cpu2 {
> + cpu-supply = <&vdd_arm>;
> +};
> +
> +&cpu3 {
> + cpu-supply = <&vdd_arm>;
> +};
> +
> +&emmc {
> + bus-width = <8>;
> + cap-mmc-highspeed;

> + max-frequency = <150000000>;

remove
already defined in dtsi

> + mmc-ddr-1_8v;
> + mmc-hs200-1_8v;
> + non-removable;
> + pinctrl-names = "default";
> + pinctrl-0 = <&emmc_clk>, <&emmc_cmd>, <&emmc_bus8>;
> + vmmc-supply = <&vcc_io>;
> + vqmmc-supply = <&vcc18_emmc>;
> + status = "okay";
> +};

////////////////////////
emmc: mmc@ff520000 {
compatible = "rockchip,rk3328-dw-mshc", "rockchip,rk3288-dw-mshc";
reg = <0x0 0xff520000 0x0 0x4000>;
interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cru HCLK_EMMC>, <&cru SCLK_EMMC>,
<&cru SCLK_EMMC_DRV>, <&cru SCLK_EMMC_SAMPLE>;
clock-names = "biu", "ciu", "ciu-drive", "ciu-sample";
fifo-depth = <0x100>;
max-frequency = <150000000>;
status = "disabled";
};
////////////////////////

> +
> +&gmac2io {
> + assigned-clocks = <&cru SCLK_MAC2IO>, <&cru SCLK_MAC2IO_EXT>;
> + assigned-clock-parents = <&gmac_clkin>, <&gmac_clkin>;
> + clock_in_out = "input";
> + phy-handle = <&rtl8211e>;
> + phy-mode = "rgmii";
> + phy-supply = <&vcc_io>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&rgmiim1_pins>;
> + snps,aal;
> + snps,rxpbl = <0x4>;
> + snps,txpbl = <0x4>;
> + tx_delay = <0x26>;
> + rx_delay = <0x11>;
> + status = "okay";
> +
> + mdio {
> + compatible = "snps,dwmac-mdio";
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + rtl8211e: ethernet-phy@1 {
> + reg = <1>;
> + pinctrl-0 = <&eth_phy_int_pin>, <&eth_phy_reset_pin>;
> + pinctrl-names = "default";
> + interrupt-parent = <&gpio1>;
> + interrupts = <24 IRQ_TYPE_LEVEL_LOW>;
> + reset-assert-us = <10000>;
> + reset-deassert-us = <50000>;
> + reset-gpios = <&gpio1 RK_PC2 GPIO_ACTIVE_LOW>;
> + };
> + };
> +};
> +
> +&gmac2phy {
> + pinctrl-names = "default";
> + pinctrl-0 = <&fephyled_linkm1>, <&fephyled_rxm1>;
> + status = "okay";
> +};
> +
> +&i2c1 {
> + status = "okay";
> +
> + rk805: pmic@18 {
> + compatible = "rockchip,rk805";
> + reg = <0x18>;
> + interrupt-parent = <&gpio2>;
> + interrupts = <6 IRQ_TYPE_LEVEL_LOW>;

> + #clock-cells = <1>;

all thing that start with "#" down the list

> + clock-output-names = "xin32k", "rk805-clkout2";
> + gpio-controller;

> + #gpio-cells = <2>;

idem

> + pinctrl-names = "default";
> + pinctrl-0 = <&pmic_int_l>;
> + rockchip,system-power-controller;
> + wakeup-source;
> +
> + vcc1-supply = <&vcc_sys>;
> + vcc2-supply = <&vcc_sys>;
> + vcc3-supply = <&vcc_sys>;
> + vcc4-supply = <&vcc_sys>;
> + vcc5-supply = <&vcc_io>;
> + vcc6-supply = <&vcc_sys>;
> +
> + regulators {
> + vdd_log: DCDC_REG1 {
> + regulator-name = "vdd_log";
> + regulator-min-microvolt = <712500>;
> + regulator-max-microvolt = <1450000>;
> + regulator-ramp-delay = <12500>;
> + regulator-always-on;
> + regulator-boot-on;
> +
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <1000000>;
> + };
> + };
> +
> + vdd_arm: DCDC_REG2 {
> + regulator-name = "vdd_arm";
> + regulator-min-microvolt = <712500>;
> + regulator-max-microvolt = <1450000>;
> + regulator-ramp-delay = <12500>;
> + regulator-always-on;
> + regulator-boot-on;
> +
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <950000>;
> + };
> + };
> +
> + vcc_ddr: DCDC_REG3 {
> + regulator-name = "vcc_ddr";
> + regulator-always-on;
> + regulator-boot-on;
> +
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + };
> + };
> +
> + vcc_io: DCDC_REG4 {
> + regulator-name = "vcc_io";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-always-on;
> + regulator-boot-on;
> +
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <3300000>;
> + };
> + };
> +
> + vcc_18: LDO_REG1 {
> + regulator-name = "vcc_18";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-always-on;
> + regulator-boot-on;
> +
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <1800000>;
> + };
> + };
> +
> + vcc18_emmc: LDO_REG2 {
> + regulator-name = "vcc18_emmc";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-always-on;
> + regulator-boot-on;
> +
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <1800000>;
> + };
> + };
> +
> + vdd_10: LDO_REG3 {
> + regulator-name = "vdd_10";
> + regulator-min-microvolt = <1000000>;
> + regulator-max-microvolt = <1000000>;
> + regulator-always-on;
> + regulator-boot-on;
> +
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <1000000>;
> + };
> + };
> + };
> + };
> +};
> +
> +&i2s1 {
> + status = "okay";
> +};
> +
> +&io_domains {
> + pmuio-supply = <&vcc_io>;
> + vccio1-supply = <&vcc_io>;
> + vccio2-supply = <&vcc18_emmc>;
> + vccio3-supply = <&vcc_io>;
> + vccio4-supply = <&vcc_io>;
> + vccio5-supply = <&vcc_io>;
> + vccio6-supply = <&vcc_io>;
> + status = "okay";
> +};
> +
> +&pinctrl {

> + ethernet-phy {

gmac2io

phy / ethernet-phy is a reserved node name
use something else

make ARCH=arm64 dtbs_check

/arch/arm64/boot/dts/rockchip/rk3328-rock-pi-e.dt.yaml: ethernet-phy:
'reg' is a required property
From schema: Documentation/devicetree/bindings/net/ethernet-phy.yaml


> + eth_phy_int_pin: eth-phy-int-pin {
> + rockchip,pins = <1 RK_PD0 RK_FUNC_GPIO &pcfg_pull_down>;
> + };
> +
> + eth_phy_reset_pin: eth-phy-reset-pin {
> + rockchip,pins = <1 RK_PC2 RK_FUNC_GPIO &pcfg_pull_down>;
> + };
> + };
> +
> + leds {
> + led_pin: led-pin {
> + rockchip,pins = <3 RK_PA5 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> + };
> +
> + pmic {
> + pmic_int_l: pmic-int-l {
> + rockchip,pins = <2 RK_PA6 RK_FUNC_GPIO &pcfg_pull_up>;
> + };
> + };
> +

> + usb3 {

usb

Last numbers in nodenames are more related to the sort order then to
capabillity.
ie: mmc0, mmc1
All usb pin related things here.

> + usb30_host_drv: usb30-host-drv {
> + rockchip,pins = <3 RK_PA7 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> + };
> +
> + wifi {
> + wifi_en: wifi-en {
> + rockchip,pins = <0 RK_PA0 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> + };
> +};
> +
> +&sdmmc {
> + bus-width = <4>;

> + cap-mmc-highspeed;

remove
micro SD only

> + cap-sd-highspeed;
> + disable-wp;
> + pinctrl-names = "default";
> + pinctrl-0 = <&sdmmc0_clk>, <&sdmmc0_cmd>, <&sdmmc0_dectn>, <&sdmmc0_bus4>;
> + vmmc-supply = <&vcc_sd>;
> + status = "okay";
> +};
> +

> +&saradc {
> + vref-supply = <&vcc_18>;
> + status = "okay";
> +};

What happened to the recovery key from the schematic?

> +
> +&tsadc {
> + status = "okay";
> +};
> +
> +&u2phy {
> + status = "okay";
> +};
> +
> +&u2phy_host {
> + status = "okay";
> +};
> +
> +&uart2 {
> + status = "okay";
> +};
> +
> +&usb_host0_ehci {
> + status = "okay";
> +};
>

\
 
 \ /
  Last update: 2021-01-10 15:46    [W:0.065 / U:37.780 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site