lkml.org 
[lkml]   [2020]   [Sep]   [27]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v10 16/16] s390/vfio-ap: update docs to include dynamic config support
On Fri, 21 Aug 2020 15:56:16 -0400
Tony Krowiak <akrowiak@linux.ibm.com> wrote:

> Update the documentation in vfio-ap.rst to include information about the
> AP dynamic configuration support (i.e., hot plug of adapters, domains
> and control domains via the matrix mediated device's sysfs assignment
> attributes).

If you don't mind I would like to skip out on commenting on the
documentation update, because of the design issues I've raised. I think
we should first clear that up. Is that OK with you?

>
> Signed-off-by: Tony Krowiak <akrowiak@linux.ibm.com>
> ---
> Documentation/s390/vfio-ap.rst | 362 ++++++++++++++++++++++++++-------
> 1 file changed, 285 insertions(+), 77 deletions(-)
>
> diff --git a/Documentation/s390/vfio-ap.rst b/Documentation/s390/vfio-ap.rst
> index e15436599086..8907aeca8fb7 100644
> --- a/Documentation/s390/vfio-ap.rst
> +++ b/Documentation/s390/vfio-ap.rst
> @@ -253,7 +253,7 @@ The process for reserving an AP queue for use by a KVM guest is:
> 1. The administrator loads the vfio_ap device driver
> 2. The vfio-ap driver during its initialization will register a single 'matrix'
> device with the device core. This will serve as the parent device for
> - all mediated matrix devices used to configure an AP matrix for a guest.
> + all matrix mediated devices used to configure an AP matrix for a guest.
> 3. The /sys/devices/vfio_ap/matrix device is created by the device core
> 4. The vfio_ap device driver will register with the AP bus for AP queue devices
> of type 10 and higher (CEX4 and newer). The driver will provide the vfio_ap
> @@ -269,7 +269,7 @@ The process for reserving an AP queue for use by a KVM guest is:
> default zcrypt cex4queue driver.
> 8. The AP bus probes the vfio_ap device driver to bind the queues reserved for
> it.
> -9. The administrator creates a passthrough type mediated matrix device to be
> +9. The administrator creates a passthrough type matrix mediated device to be
> used by a guest
> 10. The administrator assigns the adapters, usage domains and control domains
> to be exclusively used by a guest.
> @@ -279,14 +279,14 @@ Set up the VFIO mediated device interfaces
> The VFIO AP device driver utilizes the common interface of the VFIO mediated
> device core driver to:
>
> -* Register an AP mediated bus driver to add a mediated matrix device to and
> +* Register an AP mediated bus driver to add a matrix mediated device to and
> remove it from a VFIO group.
> -* Create and destroy a mediated matrix device
> -* Add a mediated matrix device to and remove it from the AP mediated bus driver
> -* Add a mediated matrix device to and remove it from an IOMMU group
> +* Create and destroy a matrix mediated device
> +* Add a matrix mediated device to and remove it from the AP mediated bus driver
> +* Add a matrix mediated device to and remove it from an IOMMU group
>
> The following high-level block diagram shows the main components and interfaces
> -of the VFIO AP mediated matrix device driver::
> +of the VFIO AP matrix mediated device driver::
>
> +-------------+
> | |
> @@ -351,29 +351,37 @@ matrix device.
> This attribute group identifies the user-defined sysfs attributes of the
> mediated device. When a device is registered with the VFIO mediated device
> framework, the sysfs attribute files identified in the 'mdev_attr_groups'
> - structure will be created in the mediated matrix device's directory. The
> - sysfs attributes for a mediated matrix device are:
> + structure will be created in the matrix mediated device's directory. The
> + sysfs attributes for a matrix mediated device are:
>
> assign_adapter / unassign_adapter:
> Write-only attributes for assigning/unassigning an AP adapter to/from the
> - mediated matrix device. To assign/unassign an adapter, the APID of the
> + matrix mediated device. To assign/unassign an adapter, the APID of the
> adapter is echoed to the respective attribute file.
> assign_domain / unassign_domain:
> Write-only attributes for assigning/unassigning an AP usage domain to/from
> - the mediated matrix device. To assign/unassign a domain, the domain
> + the matrix mediated device. To assign/unassign a domain, the domain
> number of the usage domain is echoed to the respective attribute
> file.
> matrix:
> - A read-only file for displaying the APQNs derived from the cross product
> - of the adapter and domain numbers assigned to the mediated matrix device.
> + A read-only file for displaying the APQNs derived from the Cartesian
> + product of the adapter and domain numbers assigned to the mediated matrix
> + device.
> + guest_matrix:
> + A read-only file for displaying the APQNs derived from the Cartesian
> + product of the adapter and domain numbers assigned to the APM and AQM
> + fields respectively of the KVM guest's CRYCB. This will differ from the
> + matrix if any APQNs assigned to the matrix mediated device do not
> + reference a queue device bound to the vfio_ap device driver (i.e., the
> + queue is not in the AP configuration).
> assign_control_domain / unassign_control_domain:
> Write-only attributes for assigning/unassigning an AP control domain
> - to/from the mediated matrix device. To assign/unassign a control domain,
> + to/from the matrix mediated device. To assign/unassign a control domain,
> the ID of the domain to be assigned/unassigned is echoed to the respective
> attribute file.
> control_domains:
> A read-only file for displaying the control domain numbers assigned to the
> - mediated matrix device.
> + matrix mediated device.
>
> * functions:
>
> @@ -385,7 +393,7 @@ matrix device.
> domains assigned via the corresponding sysfs attributes files
>
> remove:
> - deallocates the mediated matrix device's ap_matrix_mdev structure. This will
> + deallocates the matrix mediated device's ap_matrix_mdev structure. This will
> be allowed only if a running guest is not using the mdev.
>
> * callback interfaces
> @@ -397,7 +405,7 @@ matrix device.
> for the mdev matrix device to the MDEV bus. Access to the KVM structure used
> to configure the KVM guest is provided via this callback. The KVM structure,
> is used to configure the guest's access to the AP matrix defined via the
> - mediated matrix device's sysfs attribute files.
> + matrix mediated device's sysfs attribute files.
> release:
> unregisters the VFIO_GROUP_NOTIFY_SET_KVM notifier callback function for the
> mdev matrix device and deconfigures the guest's AP matrix.
> @@ -410,11 +418,49 @@ function is called when QEMU connects to KVM. The guest's AP matrix is
> configured via it's CRYCB by:
>
> * Setting the bits in the APM corresponding to the APIDs assigned to the
> - mediated matrix device via its 'assign_adapter' interface.
> + matrix mediated device via its 'assign_adapter' interface.
> * Setting the bits in the AQM corresponding to the domains assigned to the
> - mediated matrix device via its 'assign_domain' interface.
> + matrix mediated device via its 'assign_domain' interface.
> * Setting the bits in the ADM corresponding to the domain dIDs assigned to the
> - mediated matrix device via its 'assign_control_domains' interface.
> + matrix mediated device via its 'assign_control_domains' interface.
> +
> +The linux device model precludes passing a device through to a KVM guest that
> +is not bound to the device driver facilitating its pass-through. Consequently,
> +an APQN that does not reference a queue device bound to the vfio_ap device
> +driver will not be assigned to a KVM guest's CRYCB. The AP architecture,
> +however, does not provide a means to filter individual APQNs from the guest's
> +CRYCB, so the following logic is employed to filter them:
> +
> +* Filter the APQNs assigned to the matrix mediated device by APID.
> +
> + To filter APQNs by APID, each APQN derived from the Cartesian product of the
> + adapter numbers (APID) and domain numbers (APQI) assigned to the mdev is
> + examined and if any one of them does not reference a queue device bound to the
> + vfio_ap device driver, the adapter will not be plugged into the guest (i.e.,
> + the bit corresponding to its APID will not be set in the APM of the guest's
> + CRYCB).
> +
> + If at least one adapter is plugged into the guest, then all domains assigned
> + to the mdev will also be plugged into the guest (i.e., the bits corresponding
> + to the APQIs of the domains assigned to the mdev will be set in the AQM field
> + of the guest's CRYCB).
> +
> +* Filter the APQNs assigned to the matrix mediated device by APQI.
> +
> + The APQNs will be filtered by APQI if filtering by APID does not result in any
> + adapters or domains getting plugged into the guest.
> +
> + To filter APQNs by APQI, each APQN derived from the Cartesian product of the
> + adapter numbers (APID) and domain numbers (APQI) assigned to the mdev is
> + examined and if any one of them does not reference a queue device bound to the
> + vfio_ap device driver, the domain will not be plugged into the guest (i.e.,
> + the bit corresponding to its APQI will not be set in the AQM of the guest's
> + CRYCB).
> +
> + If at least one domain is plugged into the guest, then all adapters assigned
> + to the mdev will also be plugged into the guest (i.e., the bits corresponding
> + to the APIDs of the adapters assigned to the mdev will be set in the APM field
> + of the guest's CRYCB).
>
> The CPU model features for AP
> -----------------------------
> @@ -435,6 +481,10 @@ available to a KVM guest via the following CPU model features:
> can be made available to the guest only if it is available on the host (i.e.,
> facility bit 12 is set).
>
> +4. apqi: Indicates AP queue interrupts are available on the guest. This facility
> + can be made available to the guest only if it is available on the host (i.e.,
> + facility bit 65 is set).
> +
> Note: If the user chooses to specify a CPU model different than the 'host'
> model to QEMU, the CPU model features and facilities need to be turned on
> explicitly; for example::
> @@ -444,7 +494,7 @@ explicitly; for example::
> A guest can be precluded from using AP features/facilities by turning them off
> explicitly; for example::
>
> - /usr/bin/qemu-system-s390x ... -cpu host,ap=off,apqci=off,apft=off
> + /usr/bin/qemu-system-s390x ... -cpu host,ap=off,apqci=off,apft=off,apqi=off
>
> Note: If the APFT facility is turned off (apft=off) for the guest, the guest
> will not see any AP devices. The zcrypt device drivers that register for type 10
> @@ -530,40 +580,56 @@ These are the steps:
>
> 2. Secure the AP queues to be used by the three guests so that the host can not
> access them. To secure them, there are two sysfs files that specify
> - bitmasks marking a subset of the APQN range as 'usable by the default AP
> - queue device drivers' or 'not usable by the default device drivers' and thus
> - available for use by the vfio_ap device driver'. The location of the sysfs
> - files containing the masks are::
> + bitmasks marking a subset of the APQN range as usable only by the default AP
> + queue device drivers. All remaining APQNs are available available for use by
> + any other device driver. The vfio_ap device driver is currently the only
> + non-default device driver. The location of the sysfs files containing the
> + masks are::
>
> /sys/bus/ap/apmask
> /sys/bus/ap/aqmask
>
> The 'apmask' is a 256-bit mask that identifies a set of AP adapter IDs
> - (APID). Each bit in the mask, from left to right (i.e., from most significant
> - to least significant bit in big endian order), corresponds to an APID from
> - 0-255. If a bit is set, the APID is marked as usable only by the default AP
> - queue device drivers; otherwise, the APID is usable by the vfio_ap
> - device driver.
> + (APID). Each bit in the mask, from left to right corresponds to an APID from
> + 0-255. If a bit is set, the APID is marked as available to the default AP
> + queue device drivers.
>
> The 'aqmask' is a 256-bit mask that identifies a set of AP queue indexes
> - (APQI). Each bit in the mask, from left to right (i.e., from most significant
> - to least significant bit in big endian order), corresponds to an APQI from
> - 0-255. If a bit is set, the APQI is marked as usable only by the default AP
> - queue device drivers; otherwise, the APQI is usable by the vfio_ap device
> - driver.
> + (APQI). Each bit in the mask, from left to right corresponds to an APQI from
> + 0-255. If a bit is set, the APQI is marked as available to the default AP
> + queue device drivers.
> +
> + The Cartesian product of the APIDs corresponding to the bits set in the
> + apmask and the APQIs corresponding to the bits set in the aqmask comprise
> + the subset of APQNs that can be used only by the host default device drivers.
> + All other APQNs are available to the non-default device drivers such as the
> + vfio_ap driver.
> +
> + Take, for example, the following masks::
> +
> + apmask:
> + 0x7d00000000000000000000000000000000000000000000000000000000000000
> +
> + aqmask:
> + 0x8000000000000000000000000000000000000000000000000000000000000000
> +
> + The masks indicate:
>
> - Take, for example, the following mask::
> + * Adapters 1, 2, 3, 4, 5, and 7 are available for use by the host default
> + device drivers.
>
> - 0x7dffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffff
> + * Domain 0 is available for use by the host default device drivers
>
> - It indicates:
> + * The subset of APQNs available for use only by the default host device
> + drivers are:
>
> - 1, 2, 3, 4, 5, and 7-255 belong to the default drivers' pool, and 0 and 6
> - belong to the vfio_ap device driver's pool.
> + (1,0), (2,0), (3,0), (4.0), (5,0) and (7,0)
> +
> + * All other APQNs are available for use by the non-default device drivers.
>
> The APQN of each AP queue device assigned to the linux host is checked by the
> - AP bus against the set of APQNs derived from the cross product of APIDs
> - and APQIs marked as usable only by the default AP queue device drivers. If a
> + AP bus against the set of APQNs derived from the Cartesian product of APIDs
> + and APQIs marked as available to the default AP queue device drivers. If a
> match is detected, only the default AP queue device drivers will be probed;
> otherwise, the vfio_ap device driver will be probed.
>
> @@ -627,6 +693,16 @@ These are the steps:
> default drivers pool: adapter 0-15, domain 1
> alternate drivers pool: adapter 16-255, domains 0, 2-255
>
> + Note ***:
> + Changing a mask such that one or more APQNs will be taken from a matrix
> + mediated device (see below) will fail with an error (EADDRINUSE). The error
> + is logged to the kernel ring buffer which can be viewed with the 'dmesg'
> + command. The output identifies each APQN flagged as 'in use' and the matrix
> + mediated device to which it is assigned; for example:
> +
> + Userspace may not re-assign queue 05.0054 already assigned to 62177883-f1bb-47f0-914d-32a22e3a8804
> + Userspace may not re-assign queue 04.0054 already assigned to cef03c3c-903d-4ecc-9a83-40694cb8aee4
> +
> Securing the APQNs for our example
> ----------------------------------
> To secure the AP queues 05.0004, 05.0047, 05.00ab, 05.00ff, 06.0004, 06.0047,
> @@ -684,7 +760,7 @@ Securing the APQNs for our example
>
> /sys/devices/vfio_ap/matrix/
> --- [mdev_supported_types]
> - ------ [vfio_ap-passthrough] (passthrough mediated matrix device type)
> + ------ [vfio_ap-passthrough] (passthrough matrix mediated device type)
> --------- create
> --------- [devices]
>
> @@ -775,17 +851,18 @@ Securing the APQNs for our example
> higher than the maximum is specified, the operation will terminate with
> an error (ENODEV).
>
> - * All APQNs that can be derived from the adapter ID and the IDs of
> - the previously assigned domains must be bound to the vfio_ap device
> - driver. If no domains have yet been assigned, then there must be at least
> - one APQN with the specified APID bound to the vfio_ap driver. If no such
> - APQNs are bound to the driver, the operation will terminate with an
> - error (EADDRNOTAVAIL).
> + * All APQNs that can be derived from the Cartesian product of the APID of the
> + adapter being assigned and the APQIs of the previously assigned domains
> + must be available to the vfio_ap device driver as specified in the sysfs
> + /sys/bus/ap/apmask and /sys/bus/ap/aqmask attribute files. If even one APQN
> + is reserved for use by the host device driver, the operation will terminate
> + with an error (EADDRNOTAVAIL).
>
> - No APQN that can be derived from the adapter ID and the IDs of the
> - previously assigned domains can be assigned to another mediated matrix
> - device. If an APQN is assigned to another mediated matrix device, the
> - operation will terminate with an error (EADDRINUSE).
> + * No APQN that can be derived from the Cartesian product of the APID of the
> + adapter being assigned and the APQIs of the previously assigned domains can
> + be assigned to another matrix mediated device. If even one APQN is assigned
> + to another matrix mediated device, the operation will terminate with an
> + error (EADDRINUSE).
>
> In order to successfully assign a domain:
>
> @@ -794,17 +871,18 @@ Securing the APQNs for our example
> higher than the maximum is specified, the operation will terminate with
> an error (ENODEV).
>
> - * All APQNs that can be derived from the domain ID and the IDs of
> - the previously assigned adapters must be bound to the vfio_ap device
> - driver. If no domains have yet been assigned, then there must be at least
> - one APQN with the specified APQI bound to the vfio_ap driver. If no such
> - APQNs are bound to the driver, the operation will terminate with an
> - error (EADDRNOTAVAIL).
> + * All APQNs that can be derived from the Cartesian product of the APQI of the
> + domain being assigned and the APIDs of the previously assigned adapters
> + must be available to the vfio_ap device driver as specified in the sysfs
> + /sys/bus/ap/apmask and /sys/bus/ap/aqmask attribute files. If even one APQN
> + is reserved for use by the host device driver, the operation will terminate
> + with an error (EADDRNOTAVAIL).
>
> - No APQN that can be derived from the domain ID and the IDs of the
> - previously assigned adapters can be assigned to another mediated matrix
> - device. If an APQN is assigned to another mediated matrix device, the
> - operation will terminate with an error (EADDRINUSE).
> + * No APQN that can be derived from the Cartesian product of the APQI of the
> + domain being assigned and the APIDs of the previously assigned adapters can
> + be assigned to another matrix mediated device. If even one APQN is assigned
> + to another matrix mediated device, the operation will terminate with an
> + error (EADDRINUSE).
>
> In order to successfully assign a control domain, the domain number
> specified must represent a value from 0 up to the maximum domain number
> @@ -813,22 +891,22 @@ Securing the APQNs for our example
>
> 5. Start Guest1::
>
> - /usr/bin/qemu-system-s390x ... -cpu host,ap=on,apqci=on,apft=on \
> + /usr/bin/qemu-system-s390x ... -cpu host,ap=on,apqci=on,apft=on,apqi=on \
> -device vfio-ap,sysfsdev=/sys/devices/vfio_ap/matrix/$uuid1 ...
>
> 7. Start Guest2::
>
> - /usr/bin/qemu-system-s390x ... -cpu host,ap=on,apqci=on,apft=on \
> + /usr/bin/qemu-system-s390x ... -cpu host,ap=on,apqci=on,apft=on,apqi=on \
> -device vfio-ap,sysfsdev=/sys/devices/vfio_ap/matrix/$uuid2 ...
>
> 7. Start Guest3::
>
> - /usr/bin/qemu-system-s390x ... -cpu host,ap=on,apqci=on,apft=on \
> + /usr/bin/qemu-system-s390x ... -cpu host,ap=on,apqci=on,apft=on,apqi=on \
> -device vfio-ap,sysfsdev=/sys/devices/vfio_ap/matrix/$uuid3 ...
>
> -When the guest is shut down, the mediated matrix devices may be removed.
> +When the guest is shut down, the matrix mediated devices may be removed.
>
> -Using our example again, to remove the mediated matrix device $uuid1::
> +Using our example again, to remove the matrix mediated device $uuid1::
>
> /sys/devices/vfio_ap/matrix/
> --- [mdev_supported_types]
> @@ -851,16 +929,146 @@ remove it if no guest will use it during the remaining lifetime of the linux
> host. If the mdev matrix device is removed, one may want to also reconfigure
> the pool of adapters and queues reserved for use by the default drivers.
>
> +Hot plug support:
> +================
> +An adapter, domain or control domain may be hot plugged into a running KVM
> +guest by assigning it to the matrix mediated device being used by the guest.
> +Control domains will always be hot plugged; however, an adapter or domain will
> +be hot plugged only if each new APQN resulting from its assignment
> +references a queue device bound to the vfio_ap device driver as described
> +below.
> +
> +When an adapter is assigned to a matrix mediated device in use by a KVM guest:
> +
> +* If no domains have yet been plugged into the KVM guest:
> +
> + Hot plug the adapter and every domain previously assigned to the mdev if each
> + APQN derived from the Cartesian product of the APID of the adapter being
> + assigned and the APQIs of the domains previously assigned references a queue
> + device bound to the vfio_ap device driver.
> +
> +* If one or more domains have previously been plugged into the guest:
> +
> + Hot plug the adapter if each APQN derived from the Cartesian product of the
> + APID of the adapter being assigned and the APQIs of the domains already
> + plugged into the guest references a queue device bound to the vfio_ap device
> + driver.
> +
> +When a domain is assigned to a matrix mediated device in use by a KVM guest:
> +
> +* If no adapters have yet been plugged into the KVM guest:
> +
> + Hot plug the domain and every adapter previously assigned to the mdev if each
> + APQN derived from the Cartesian product of the APIDs of the adapters
> + previously assigned and the APQI of the domain being assigned references a
> + queue device bound to the vfio_ap device driver.
> +
> +* If one or more adapters have previously been plugged into the guest:
> +
> + Hot plug the domain if each APQN derived from the Cartesian product of the
> + APIDs of the adapters already plugged into the guest and the APQI of the
> + domain being assigned references a queue device bound to the vfio_ap device
> + driver.
> +
> +Over-provisioning of AP queues for a KVM guest:
> +==============================================
> +Over-provisioning is defined herein as the assignment of adapters or domains to
> +a matrix mediated device that do not reference AP devices in the host's AP
> +configuration. The idea here is that when the adapter or domain becomes
> +available, it will be automatically hot-plugged into the KVM guest using
> +the matrix mediated device to which it is assigned as long as each new APQN
> +resulting from plugging it in references a queue device bound to the vfio_ap
> +device driver.
> +
> Limitations
> ===========
> -* The KVM/kernel interfaces do not provide a way to prevent restoring an APQN
> - to the default drivers pool of a queue that is still assigned to a mediated
> - device in use by a guest. It is incumbent upon the administrator to
> - ensure there is no mediated device in use by a guest to which the APQN is
> - assigned lest the host be given access to the private data of the AP queue
> - device such as a private key configured specifically for the guest.
> +Live guest migration is not supported for guests using AP devices without
> +intervention by a system administrator. Before a KVM guest can be migrated,
> +the matrix mediated device must be removed. Unfortunately, it can not be
> +removed manually (i.e., echo 1 > /sys/devices/vfio_ap/matrix/$UUID/remove) while
> +the mdev is in use by a KVM guest. If the guest is being emulated by QEMU,
> +its mdev can be hot unplugged from the guest in one of two ways:
> +
> +1. If the KVM guest was started with libvirt, you can hot unplug the mdev via
> + the following commands:
> +
> + virsh detach-device <guestname> <path-to-device-xml>
> +
> + For example, to hot unplug mdev 62177883-f1bb-47f0-914d-32a22e3a8804 from
> + the guest named 'my-guest':
> +
> + virsh detach-device my-guest ~/config/my-guest-hostdev.xml
> +
> + The contents of my-guest-hostdev.xml:
> +
> + <hostdev mode='subsystem' type='mdev' managed='no' model='vfio-ap'>
> + <source>
> + <address uuid='62177883-f1bb-47f0-914d-32a22e3a8804'/>
> + </source>
> + </hostdev>
> +
> +
> + virsh qemu-monitor-command <guest-name> --hmp "device-del <device-id>"
> +
> + For example, to hot unplug the matrix mediated device identified on the
> + qemu command line with 'id=hostdev0' from the guest named 'my-guest':
> +
> + virsh qemu-monitor-command my-guest --hmp "device_del hostdev0"
> +
> +2. A matrix mediated device can be hot unplugged by attaching the qemu monitor
> + to the guest and using the following qemu monitor command:
> +
> + (QEMU) device-del id=<device-id>
> +
> + For example, to hot unplug the matrix mediated device that was specified
> + on the qemu command line with 'id=hostdev0' when the guest was started:
> +
> + (QEMU) device-del id=hostdev0
> +
> +After live migration of the KVM guest completes, an AP configuration can be
> +restored to the KVM guest by hot plugging a matrix mediated device on the target
> +system into the guest in one of two ways:
> +
> +1. If the KVM guest was started with libvirt, you can hot plug a matrix mediated
> + device into the guest via the following virsh commands:
> +
> + virsh attach-device <guestname> <path-to-device-xml>
> +
> + For example, to hot plug mdev 62177883-f1bb-47f0-914d-32a22e3a8804 into
> + the guest named 'my-guest':
> +
> + virsh attach-device my-guest ~/config/my-guest-hostdev.xml
> +
> + The contents of my-guest-hostdev.xml:
> +
> + <hostdev mode='subsystem' type='mdev' managed='no' model='vfio-ap'>
> + <source>
> + <address uuid='62177883-f1bb-47f0-914d-32a22e3a8804'/>
> + </source>
> + </hostdev>
> +
> +
> + virsh qemu-monitor-command <guest-name> --hmp \
> + "device_add vfio-ap,sysfsdev=<path-to-mdev>,id=<device-id>"
> +
> + For example, to hot plug the matrix mediated device
> + 62177883-f1bb-47f0-914d-32a22e3a8804 into the guest named 'my-guest' with
> + device-id hostdev0:
> +
> + virsh qemu-monitor-command my-guest --hmp \
> + "device_add vfio-ap,\
> + sysfsdev=/sys/devices/vfio_ap/matrix/62177883-f1bb-47f0-914d-32a22e3a8804,\
> + id=hostdev0"
> +
> +2. A matrix mediated device can be hot plugged by attaching the qemu monitor
> + to the guest and using the following qemu monitor command:
> +
> + (qemu) device_add "vfio-ap,sysfsdev=<path-to-mdev>,id=<device-id>"
>
> -* Dynamically modifying the AP matrix for a running guest (which would amount to
> - hot(un)plug of AP devices for the guest) is currently not supported
> + For example, to plug the matrix mediated device
> + 62177883-f1bb-47f0-914d-32a22e3a8804 into the guest with the device-id
> + hostdev0:
>
> -* Live guest migration is not supported for guests using AP devices.
> + (QEMU) device-add "vfio-ap,\
> + sysfsdev=/sys/devices/vfio_ap/matrix/62177883-f1bb-47f0-914d-32a22e3a8804,\
> + id=hostdev0"
> \ No newline at end of file

\
 
 \ /
  Last update: 2020-09-28 04:50    [W:0.667 / U:2.416 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site