lkml.org 
[lkml]   [2020]   [Sep]   [27]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH v3 1/1] PCI/ERR: Fix reset logic in pcie_do_recovery() call
From
Date
Hi,

On 9/25/20 11:30 AM, Sinan Kaya wrote:
> On 9/25/2020 2:16 PM, Kuppuswamy, Sathyanarayanan wrote:
>>>
>>> If this is a too involved change, DPC driver should restore state
>>> when hotplug is not supported.
>> Yes. we can add a condition for hotplug capability check.
>>>
>>> DPC driver should be self-sufficient by itself.
>>>
>
> Sounds good.
>
>>>> Also for non-fatal errors, if reset is requested then we still need
>>>> some kind of bus reset call here
>>>
>>> DPC should handle both fatal and non-fatal cases
>> Currently DPC is only triggered for FATAL errors.
>>  and cause a bus reset
>
> Thanks for the heads up.
> This seems to have changed since I looked at the DPC code.
>
>>> in hardware already before triggering an interrupt.
>> Error recovery is not triggered only DPC driver. AER also uses the
>> same error recovery code. If DPC is not supported, then we still need
>> reset logic.
>
> It sounds like we are cross-talking two issues.
>
> 1. no state restore on DPC after FATAL error.
> Let's fix this.
Agree. Few more detail about the above issue is,

There are two cases under FATAL error.

FATAL + hotplug - In this case, link will be reseted. And hotplug handler
will remove the driver state. This case works well with current code.

FATAL + no-hotplug - In this case, link will still be reseted. But
currently driver state is not properly restored. So I attempted
to restore it using pci_reset_bus().

status = reset_link(dev);
- if (status != PCI_ERS_RESULT_RECOVERED) {
+ if (status == PCI_ERS_RESULT_RECOVERED) {
+ status = PCI_ERS_RESULT_NEED_RESET;

...

if (status == PCI_ERS_RESULT_NEED_RESET) {
/*
- * TODO: Should call platform-specific
- * functions to reset slot before calling
- * drivers' slot_reset callbacks?
+ * TODO: Optimize the call to pci_reset_bus()
+ *
+ * There are two components to pci_reset_bus().
+ *
+ * 1. Do platform specific slot/bus reset.
+ * 2. Save/Restore all devices in the bus.
+ *
+ * For hotplug capable devices and fatal errors,
+ * device is already in reset state due to link
+ * reset. So repeating platform specific slot/bus
+ * reset via pci_reset_bus() call is redundant. So
+ * can optimize this logic and conditionally call
+ * pci_reset_bus().
*/
+ pci_reset_bus(dev);

>
> 2. no bus reset on NON_FATAL error through AER driver path.
> This already tells me that you need to split your change into
> multiple patches.
>
> Let's talk about this too. bus reset should be triggered via
> AER driver before informing the recovery.
But as per error recovery documentation, any call to
->error_detected() or ->mmio_enabled() can request
PCI_ERS_RESULT_NEED_RESET. So we need to add code
to do the actual reset before calling ->slot_reset()
callback. So call to pci_reset_bus() fixes this
issue.

if (status == PCI_ERS_RESULT_NEED_RESET) {
+ pci_reset_bus(dev);


>
> if (status == PCI_ERS_RESULT_NEED_RESET) {
> /*
> * TODO: Should call platform-specific
> * functions to reset slot before calling
> * drivers' slot_reset callbacks?
> */
> status = PCI_ERS_RESULT_RECOVERED;
> pci_dbg(dev, "broadcast slot_reset message\n");
> pci_walk_bus(bus, report_slot_reset, &status);
> }
>

--
Sathyanarayanan Kuppuswamy
Linux Kernel Developer

\
 
 \ /
  Last update: 2020-09-28 04:44    [W:1.067 / U:0.532 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site