lkml.org 
[lkml]   [2020]   [Aug]   [14]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Date
SubjectRe: [PATCH] serial: sh-sci: Make sure status register SCxSR is read in correct sequence
On Wed, Apr 15, 2020 at 2:36 PM Geert Uytterhoeven <geert@linux-m68k.org> wrote:
> On Thu, Apr 2, 2020 at 5:24 PM Geert Uytterhoeven <geert@linux-m68k.org> wrote:
> > On Thu, Apr 2, 2020 at 1:28 PM Lad, Prabhakar
> > <prabhakar.csengg@gmail.com> wrote:
> > > On Wed, Apr 1, 2020 at 1:43 PM Geert Uytterhoeven <geert@linux-m68k.org> wrote:
> > > > On Tue, Mar 31, 2020 at 5:58 PM Prabhakar Mahadev Lad
> > > > <prabhakar.mahadev-lad.rj@bp.renesas.com> wrote:
> > > > > > -----Original Message-----
> > > > > > From: Geert Uytterhoeven <geert@linux-m68k.org>
> > > > > > On Fri, Mar 27, 2020 at 7:17 PM Kazuhiro Fujita
> > > > > > <kazuhiro.fujita.jg@renesas.com> wrote:
> > > > > > > For SCIF and HSCIF interfaces the SCxSR register holds the status of
> > > > > > > data that is to be read next from SCxRDR register, But where as for
> > > > > > > SCIFA and SCIFB interfaces SCxSR register holds status of data that is
> > > > > > > previously read from SCxRDR register.
> > > > > > >
> > > > > > > This patch makes sure the status register is read depending on the port
> > > > > > > types so that errors are caught accordingly.
> > > > > > >
> > > > > > > Cc: <stable@vger.kernel.org>
> > > > > > > Signed-off-by: Kazuhiro Fujita <kazuhiro.fujita.jg@renesas.com>
> > > > > > > Signed-off-by: Hao Bui <hao.bui.yg@renesas.com>
> > > > > > > Signed-off-by: KAZUMI HARADA <kazumi.harada.rh@renesas.com>
> > > > > > > Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
> > > >
> > > > > > Nevertheless, this patch will need some testing on various hardware.
> > > > > > Do you have a test case to verify the broken/fixed behavior?
> > > > > >
> > > > > Agreed, its been tested on RZ/G2x & RZ/G1x by doing a loopback test, configure one interface as CS8 mode(8-bits data, No parity) and other as CS7 mode (7-bits data, 1-bit Parity) and parity errors should be detected.
> > > >
> > > > This can easily be tested on the console. Basic testing can even be
> > > > done with an unmodified kernel, as there is already a "parity error"
> > > > notice message in the driver.
> > > >
> > > > Enable even parity on the console:
> > > >
> > > > $ stty evenp
> > > >
> > > > (use "oddp" for odd parity, and invert all below)
> > > >
> > > > Typing e.g. a single "p" should trigger a parity error.
> > > > Typing "o" shouldn't.
> > > > Without this patch, no parity error is detected on SCIF.
> > > >
> > > > Likewise, pasting a sequence of "p" characters should trigger a lot of
> > > > parity errors, "o" shouldn't.
> > > > Without this patch, parity errors are detected on SCIF, except for the
> > > > first character.
> > > >
> > > > For more advanced testing, make the following change to the driver:
> > > >
> > > > - dev_notice(port->dev, "parity error\n");
> > > > + dev_notice(port->dev, "parity error for char 0x%02x hweight %u\n",
> > > > c, hweight8(c));
> > > >
> > > > Pasting an alternating sequence of "p" and "o" characters should trigger
> > > > parity errors for the "p" characters.
> > > > Without this patch, they are triggered for the "o" characters instead.
> > > >
> > > Thank you that makes life easier.
> > >
> > > > With this patch, the issues above are fixed on SCIF.
> > > > This has been verified on:
> > > > 1. SCIF on R-Car Gen 2,
> > > > 2. SCIF on R-Car Gen3
> > > > 3. SCIF on RZ/A1H,
> > > > 4. SCIF on RZ/A2M.
>
> > If I disable DMA for HSCIF1 in the .dtsi, parity errors are detected
> > as expected.
>
> So HSCIF on R-Car Gen3 is affected, and fixed by this patch.
>
> > Hence the driver does not support parity checking when DMA is enabled.
> > I also think it's not easy to add support for that, if possible at all.
> >
> > > > I haven't tested it yet on:
> > > > 1. SCIFB on SH/R-Mobile (needs wiring up),
>
> SCIFB on R-Mobile A1 is not affected, and works before/after, as expected.
>
> > > > 2. SCIFA, SCIFB, and HSCIF on R-Car Gen2 (needs wiring up),
>
> Same for SCIFA, SCIFB on R-Car M2-W.
>
> HSCIF on R-Car M2-W is affected, and fixed by this patch.
>
> This means the modern platforms we care about are handled fine, so
> Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
>
> That leaves us with testing on a few legacy platforms...
>
> > > > 3. (H)SCIF on R-Car Gen1 (remote boards unaccessible at the moment),
> > > > 4. SuperH (only remote Migo-R available, but unaccessible).
> > > >
> > > > I can test 1 and 2 (and perhaps 3 and 4) later, if needed.
> > > probably testing this on SuperH is gonna be a pain due to lack of
> > > hardware availability,
> > > (it needs to be tested on 19 platforms)
> > > how about #ifdef CONFIG_ARCH_RENESAS || CONFIG_H8300 and the fix ?
> >
> > I had a look at a few SuperH docs w.r.t. framing/parity error behavior:
> > - SCIF(A) on SH7724: similar to R-Car Gen2,
> > - H(SCIF) on SH7734: same as on R-Car Gen2,
> > - SCIF on SH7751: conflict between status register ("to be read next")
> > and flowchart ("read from").

FTR, I gave it a try on the SH7751R-based I-O DATA USL-5P aka Landisk:
SCIF is affected, and fixed by commit 3dc4db3662366306 ("serial: sh-sci:
Make sure status register SCxSR is read in correct sequence").

Gr{oetje,eeting}s,

Geert

--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert@linux-m68k.org

In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
-- Linus Torvalds

\
 
 \ /
  Last update: 2020-08-14 17:26    [W:0.061 / U:6.684 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site