lkml.org 
[lkml]   [2020]   [Aug]   [12]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH 01/11] dt-bindings: extcon: ptn5150: Convert binding to DT schema
Date
Convert the ptn-5150 extcon driver bindings to DT schema format using
json-schema. The differences with original bindings document:
- Use "gpios" suffix for the "int" and "vbus" gpio,
- Skip generic properties like "reg" or "pinctrl".

Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
---
.../bindings/extcon/extcon-ptn5150.txt | 27 ----------
.../bindings/extcon/extcon-ptn5150.yaml | 53 +++++++++++++++++++
2 files changed, 53 insertions(+), 27 deletions(-)
delete mode 100644 Documentation/devicetree/bindings/extcon/extcon-ptn5150.txt
create mode 100644 Documentation/devicetree/bindings/extcon/extcon-ptn5150.yaml

diff --git a/Documentation/devicetree/bindings/extcon/extcon-ptn5150.txt b/Documentation/devicetree/bindings/extcon/extcon-ptn5150.txt
deleted file mode 100644
index 936fbdf12815..000000000000
--- a/Documentation/devicetree/bindings/extcon/extcon-ptn5150.txt
+++ /dev/null
@@ -1,27 +0,0 @@
-* PTN5150 CC (Configuration Channel) Logic device
-
-PTN5150 is a small thin low power CC logic chip supporting the USB Type-C
-connector application with CC control logic detection and indication functions.
-It is interfaced to the host controller using an I2C interface.
-
-Required properties:
-- compatible: should be "nxp,ptn5150"
-- reg: specifies the I2C slave address of the device
-- int-gpio: should contain a phandle and GPIO specifier for the GPIO pin
- connected to the PTN5150's INTB pin.
-- vbus-gpio: should contain a phandle and GPIO specifier for the GPIO pin which
- is used to control VBUS.
-- pinctrl-names : a pinctrl state named "default" must be defined.
-- pinctrl-0 : phandle referencing pin configuration of interrupt and vbus
- control.
-
-Example:
- ptn5150@1d {
- compatible = "nxp,ptn5150";
- reg = <0x1d>;
- int-gpio = <&msmgpio 78 GPIO_ACTIVE_HIGH>;
- vbus-gpio = <&msmgpio 148 GPIO_ACTIVE_HIGH>;
- pinctrl-names = "default";
- pinctrl-0 = <&ptn5150_default>;
- status = "okay";
- };
diff --git a/Documentation/devicetree/bindings/extcon/extcon-ptn5150.yaml b/Documentation/devicetree/bindings/extcon/extcon-ptn5150.yaml
new file mode 100644
index 000000000000..f6316f12028b
--- /dev/null
+++ b/Documentation/devicetree/bindings/extcon/extcon-ptn5150.yaml
@@ -0,0 +1,53 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/extcon/extcon-ptn5150.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: PTN5150 CC (Configuration Channel) Logic device
+
+maintainers:
+ - Krzysztof Kozlowski <krzk@kernel.org>
+
+description: |
+ PTN5150 is a small thin low power CC logic chip supporting the USB Type-C
+ connector application with CC control logic detection and indication
+ functions. It is interfaced to the host controller using an I2C interface.
+
+properties:
+ compatible:
+ const: nxp,ptn5150
+
+ int-gpios:
+ description:
+ GPIO pin (input) connected to the PTN5150's INTB pin.
+
+ reg:
+ maxItems: 1
+
+ vbus-gpios:
+ description:
+ GPIO pin (output) used to control VBUS.
+
+required:
+ - compatible
+ - int-gpios
+ - reg
+ - vbus-gpios
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/gpio/gpio.h>
+ i2c {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ptn5150@1d {
+ compatible = "nxp,ptn5150";
+ reg = <0x1d>;
+ int-gpios = <&msmgpio 78 GPIO_ACTIVE_HIGH>;
+ vbus-gpios = <&msmgpio 148 GPIO_ACTIVE_HIGH>;
+ };
+ };
--
2.17.1
\
 
 \ /
  Last update: 2020-08-12 18:30    [W:0.060 / U:1.356 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site