Messages in this thread |  | | From | "Doug Smythies" <> | Subject | RE: [PATCH 2/2] cpufreq: intel_pstate: Use passive mode by default without HWP | Date | Thu, 9 Jul 2020 14:01:11 -0700 |
| |
Hi Rafael,
As you may or may not recall, I am attempting to untangle and separate multiple compounding issues around the intel_pstate driver and HWP (or not).
Until everything is figured out, I am using the following rules:
. never use x86_energy_perf_policy. . For HWP disabled: never change from active to passive or via versa, but rather do it via boot. . after boot always check and reset the various power limit log bits that are set. . never compile the kernel (well, until after any tests), which will set those bits again. . never run prime95 high heat torture test, which will set those bits again. . try to never do anything else that will set those bits again.
On 2020.03.28 05:58 Rafael J. Wysocki wrote: > > From: "Rafael J. Wysocki" <rafael.j.wysocki@intel.com> > > After recent changes allowing scale-invariant utilization to be > used on x86, the schedutil governor on top of intel_pstate in the > passive mode should be on par with (or better than) the active mode > "powersave" algorithm of intel_pstate on systems in which > hardware-managed P-states (HWP) are not used, so it should not be > necessary to use the internal scaling algorithm in those cases. > > Accordingly, modify intel_pstate to start in the passive mode by > default if the processor at hand does not support HWP of if the driver > is requested to avoid using HWP through the kernel command line. > > Among other things, that will allow utilization clamps and the > support for RT/DL tasks in the schedutil governor to be utilized on > systems in which intel_pstate is used. > > Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> > --- > Documentation/admin-guide/pm/intel_pstate.rst | 32 ++++++++++++++++----------- > drivers/cpufreq/intel_pstate.c | 3 ++- > 2 files changed, 21 insertions(+), 14 deletions(-) > > diff --git a/Documentation/admin-guide/pm/intel_pstate.rst b/Documentation/admin- > guide/pm/intel_pstate.rst > index ad392f3aee06..39d80bc29ccd 100644 > --- a/Documentation/admin-guide/pm/intel_pstate.rst > +++ b/Documentation/admin-guide/pm/intel_pstate.rst > @@ -62,9 +62,10 @@ on the capabilities of the processor. > Active Mode > ----------- > > -This is the default operation mode of ``intel_pstate``. If it works in this > -mode, the ``scaling_driver`` policy attribute in ``sysfs`` for all ``CPUFreq`` > -policies contains the string "intel_pstate". > +This is the default operation mode of ``intel_pstate`` for processors with > +hardware-managed P-states (HWP) support. If it works in this mode, the > +``scaling_driver`` policy attribute in ``sysfs`` for all ``CPUFreq`` policies > +contains the string "intel_pstate". > > In this mode the driver bypasses the scaling governors layer of ``CPUFreq`` and > provides its own scaling algorithms for P-state selection. Those algorithms > @@ -138,12 +139,13 @@ internal P-state selection logic to be less performance-focused. > Active Mode Without HWP > ~~~~~~~~~~~~~~~~~~~~~~~ > > -This is the default operation mode for processors that do not support the HWP > -feature. It also is used by default with the ``intel_pstate=no_hwp`` argument > -in the kernel command line. However, in this mode ``intel_pstate`` may refuse > -to work with the given processor if it does not recognize it. [Note that > -``intel_pstate`` will never refuse to work with any processor with the HWP > -feature enabled.] > +This operation mode is optional for processors that do not support the HWP > +feature or when the ``intel_pstate=no_hwp`` argument is passed to the kernel in > +the command line. The active mode is used in those cases if the > +``intel_pstate=active`` argument is passed to the kernel in the command line.
??? I can not see anywhere in the code where the kernel command line argument "intel_pstate=active" is dealt with.
> +In this mode ``intel_pstate`` may refuse to work with processors that are not > +recognized by it. [Note that ``intel_pstate`` will never refuse to work with > +any processor with the HWP feature enabled.] > > In this mode ``intel_pstate`` registers utilization update callbacks with the > CPU scheduler in order to run a P-state selection algorithm, either > @@ -188,10 +190,14 @@ is not set. > Passive Mode > ------------ > > -This mode is used if the ``intel_pstate=passive`` argument is passed to the > -kernel in the command line (it implies the ``intel_pstate=no_hwp`` setting too). > -Like in the active mode without HWP support, in this mode ``intel_pstate`` may > -refuse to work with the given processor if it does not recognize it. > +This is the default operation mode of ``intel_pstate`` for processors without > +hardware-managed P-states (HWP) support. It is always used if the > +``intel_pstate=passive`` argument is passed to the kernel in the command line > +regardless of whether or not the given processor supports HWP. [Note that the > +``intel_pstate=no_hwp`` setting implies ``intel_pstate=passive`` if it is used > +without ``intel_pstate=active``.]
??? as above. I can not see where intel_pstate=active is dealt with in the code.
> Like in the active mode without HWP support, > +in this mode ``intel_pstate`` may refuse to work with processors that are not > +recognized by it. > > If the driver works in this mode, the ``scaling_driver`` policy attribute in > ``sysfs`` for all ``CPUFreq`` policies contains the string "intel_cpufreq". > diff --git a/drivers/cpufreq/intel_pstate.c b/drivers/cpufreq/intel_pstate.c > index d2297839374d..b24a5c5ec4f9 100644 > --- a/drivers/cpufreq/intel_pstate.c > +++ b/drivers/cpufreq/intel_pstate.c > @@ -2769,6 +2769,8 @@ static int __init intel_pstate_init(void) > pr_info("Invalid MSRs\n"); > return -ENODEV; > } > + /* Without HWP start in the passive mode. */ > + default_driver = &intel_cpufreq; > > hwp_cpu_matched: > /* > @@ -2814,7 +2816,6 @@ static int __init intel_pstate_setup(char *str) > if (!strcmp(str, "disable")) { > no_load = 1; > } else if (!strcmp(str, "passive")) { > - pr_info("Passive mode enabled\n"); > default_driver = &intel_cpufreq; > no_hwp = 1; > } > -- > 2.16.4
Example 1: i5-9600k (hwp capable) (kernel 5.8-rc4):
Grub: GRUB_CMDLINE_LINUX_DEFAULT="ipv6.disable=1 consoleblank=450 intel_pstate=active intel_pstate=no_hwp cpuidle_sysfs_switch cpuidle.governor=teo"
/proc/cmdline: BOOT_IMAGE=/boot/vmlinuz-5.8.0-rc4-stock root=UUID=0ac356c1-caa9-4c2e-8229-4408bd998dbd ro ipv6.disable=1 consoleblank=450 intel_pstate=active intel_pstate=no_hwp cpuidle_sysfs_switch cpuidle.governor=teo
Result:
doug@s18:~$ grep . /sys/devices/system/cpu/cpu*/cpufreq/scaling_driver /sys/devices/system/cpu/cpu0/cpufreq/scaling_driver:intel_cpufreq /sys/devices/system/cpu/cpu1/cpufreq/scaling_driver:intel_cpufreq /sys/devices/system/cpu/cpu2/cpufreq/scaling_driver:intel_cpufreq /sys/devices/system/cpu/cpu3/cpufreq/scaling_driver:intel_cpufreq /sys/devices/system/cpu/cpu4/cpufreq/scaling_driver:intel_cpufreq /sys/devices/system/cpu/cpu5/cpufreq/scaling_driver:intel_cpufreq
Example 2: i7-2600k (does not have hwp) (kernel 5.8-rc1)
Grub: GRUB_CMDLINE_LINUX_DEFAULT="ipv6.disable=1 consoleblank=300 intel_pstate=active cpuidle_sysfs_switch cpuidle.governor=teo"
/proc/cmdline: BOOT_IMAGE=/boot/vmlinuz-5.8.0-rc1-stock root=UUID=bcbc624b-892b-46ca-9e9e-102daf644170 ro ipv6.disable=1 consoleblank=300 intel_pstate=active cpuidle_sysfs_switch cpuidle.governor=teo
Result:
doug@s15:~$ grep . /sys/devices/system/cpu/cpu*/cpufreq/scaling_driver /sys/devices/system/cpu/cpu0/cpufreq/scaling_driver:intel_cpufreq /sys/devices/system/cpu/cpu1/cpufreq/scaling_driver:intel_cpufreq /sys/devices/system/cpu/cpu2/cpufreq/scaling_driver:intel_cpufreq /sys/devices/system/cpu/cpu3/cpufreq/scaling_driver:intel_cpufreq /sys/devices/system/cpu/cpu4/cpufreq/scaling_driver:intel_cpufreq /sys/devices/system/cpu/cpu5/cpufreq/scaling_driver:intel_cpufreq /sys/devices/system/cpu/cpu6/cpufreq/scaling_driver:intel_cpufreq /sys/devices/system/cpu/cpu7/cpufreq/scaling_driver:intel_cpufreq
... Doug
|  |