lkml.org 
[lkml]   [2020]   [May]   [20]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH v2 04/12] i2c: designware: Convert driver to using regmap API
From
Date
On 5/10/20 12:50 PM, Serge Semin wrote:
> Seeing the DW I2C driver is using flags-based accessors with two
> conditional clauses it would be better to replace them with the regmap
> API IO methods and to initialize the regmap object with read/write
> callbacks specific to the controller registers map implementation. This
> will be also handy for the drivers with non-standard registers mapping
> (like an embedded into the Baikal-T1 System Controller DW I2C block, which
> glue-driver is a part of this series).
>
> As before the driver tries to detect the mapping setup at probe stage and
> creates a regmap object accordingly, which will be used by the rest of the
> code to correctly access the controller registers. In two places it was
> appropriate to convert the hand-written read-modify-write and
> read-poll-loop design patterns to the corresponding regmap API
> ready-to-use methods.
>
> Note the regmap IO methods return value is checked only at the probe
> stage. The rest of the code won't do this because basically we have
> MMIO-based regmap so non of the read/write methods can fail (this also
> won't be needed for the Baikal-T1-specific I2C controller).
>
> Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
> Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
> Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
> Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
> Cc: Paul Burton <paulburton@kernel.org>
> Cc: Ralf Baechle <ralf@linux-mips.org>
> Cc: Wolfram Sang <wsa@the-dreams.de>
> Cc: Rob Herring <robh+dt@kernel.org>
> Cc: Frank Rowand <frowand.list@gmail.com>
> Cc: devicetree@vger.kernel.org
> Cc: linux-mips@vger.kernel.org
> ---
> drivers/i2c/busses/Kconfig | 1 +
> drivers/i2c/busses/i2c-designware-common.c | 171 +++++++++++++++------
> drivers/i2c/busses/i2c-designware-core.h | 18 +--
> drivers/i2c/busses/i2c-designware-master.c | 125 ++++++++-------
> drivers/i2c/busses/i2c-designware-slave.c | 77 +++++-----
> 5 files changed, 239 insertions(+), 153 deletions(-)
>
Looking at patches 4/12-12/12 I think it would be good to move fixes and
less invasive patches before this. Like

i2c: designware: slave: Set DW I2C core module dependency
i2c: designware: Use `-y` to build multi-object modules
i2c: designware: Move Baytrail sem config to the platform if-clause

That said, you may add:

Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>

\
 
 \ /
  Last update: 2020-05-20 14:16    [W:0.147 / U:3.304 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site