lkml.org 
[lkml]   [2020]   [Apr]   [3]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v6 1/3] media: dt-bindings: ov8856: Document YAML bindings
Hi Robert,

On Thu, Apr 02, 2020 at 12:10:00PM +0200, Robert Foss wrote:
> Hey Maxime,
>
> On Wed, 1 Apr 2020 at 10:07, Maxime Ripard <maxime@cerno.tech> wrote:
> >
> > Hi,
> >
> > On Tue, Mar 31, 2020 at 03:33:44PM +0200, Robert Foss wrote:
> > > From: Dongchun Zhu <dongchun.zhu@mediatek.com>
> > >
> > > This patch adds documentation of device tree in YAML schema for the
> > > OV8856 CMOS image sensor.
> > >
> > > Signed-off-by: Dongchun Zhu <dongchun.zhu@mediatek.com>
> > > Signed-off-by: Robert Foss <robert.foss@linaro.org>
> > > ---
> > >
> > > - Changes since v5:
> > > * Add assigned-clocks and assigned-clock-rates
> > > * robher: dt-schema errors
> > >
> > > - Changes since v4:
> > > * Fabio: Change reset-gpio to GPIO_ACTIVE_LOW, explain in description
> > > * Add clock-lanes property to example
> > > * robher: Fix syntax error in devicetree example
> > >
> > > - Changes since v3:
> > > * robher: Fix syntax error
> > > * robher: Removed maxItems
> > > * Fixes yaml 'make dt-binding-check' errors
> > >
> > > - Changes since v2:
> > > Fixes comments from from Andy, Tomasz, Sakari, Rob.
> > > * Convert text documentation to YAML schema.
> > >
> > > - Changes since v1:
> > > Fixes comments from Sakari, Tomasz
> > > * Add clock-frequency and link-frequencies in DT
> > >
> > > .../devicetree/bindings/media/i2c/ov8856.yaml | 150 ++++++++++++++++++
> > > MAINTAINERS | 1 +
> > > 2 files changed, 151 insertions(+)
> > > create mode 100644 Documentation/devicetree/bindings/media/i2c/ov8856.yaml
> > >
> > > diff --git a/Documentation/devicetree/bindings/media/i2c/ov8856.yaml b/Documentation/devicetree/bindings/media/i2c/ov8856.yaml
> > > new file mode 100644
> > > index 000000000000..beeddfbb8709
> > > --- /dev/null
> > > +++ b/Documentation/devicetree/bindings/media/i2c/ov8856.yaml
> > > @@ -0,0 +1,150 @@
> > > +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
> > > +# Copyright (c) 2019 MediaTek Inc.
> > > +%YAML 1.2
> > > +---
> > > +$id: http://devicetree.org/schemas/media/i2c/ov8856.yaml#
> > > +$schema: http://devicetree.org/meta-schemas/core.yaml#
> > > +
> > > +title: Omnivision OV8856 CMOS Sensor Device Tree Bindings
> > > +
> > > +maintainers:
> > > + - Ben Kao <ben.kao@intel.com>
> > > + - Dongchun Zhu <dongchun.zhu@mediatek.com>
> > > +
> > > +description: |-
> > > + The Omnivision OV8856 is a high performance, 1/4-inch, 8 megapixel, CMOS
> > > + image sensor that delivers 3264x2448 at 30fps. It provides full-frame,
> > > + sub-sampled, and windowed 10-bit MIPI images in various formats via the
> > > + Serial Camera Control Bus (SCCB) interface. This chip is programmable
> > > + through I2C and two-wire SCCB. The sensor output is available via CSI-2
> > > + serial data output (up to 4-lane).
> > > +
> > > +properties:
> > > + compatible:
> > > + const: ovti,ov8856
> > > +
> > > + reg:
> > > + maxItems: 1
> > > +
> > > + clocks:
> > > + maxItems: 1
> > > +
> > > + clock-names:
> > > + description:
> > > + Input clock for the sensor.
> > > + items:
> > > + - const: xvclk
> > > +
> > > + clock-frequency:
> > > + description:
> > > + Frequency of the xvclk clock in Hertz.
> >
> > We also had that discussion recently for another omnivision sensor
> > (ov5645 iirc), but what is clock-frequency useful for?
> >
> > It seems that the sensor is passed in clocks, so if you need to
> > retrieve the clock rate you should use the clock API instead.
> >
> > Looking at the driver, it looks like it first retrieves the clock, set
> > it to clock-frequency, and then checks that this is OV8856_XVCLK_19_2
> > (19.2 MHz).
>
> As far as I understand it, 19.2MHz is requirement for the sensor mode
> that currently defaults to. Some modes require higher clock speeds
> than this however.

It's very system specific. Either way, bindings should not assume a
particular driver implementation.

>
> >
> > The datasheet says that the sensor can have any frequency in the 6 -
> > 27 MHz range, so this is a driver limitation and should be set in the
> > driver using the clock API, and you can always bail out if it doesn't
> > provide a rate that is not acceptable for the drivers assumption.
> >
> > In any case, you don't need clock-frequency here...
>
> So your suggestion is that we remove all clocks-rate properties, and
> replace the clk_get_rate() calls in the driver with clk_set_rate()
> calls for the desired frequencies?

The driver shouldn't set the rate here unless it gets it from DT (but that
was not the intention). So the driver should get the frequency instead.

--
Regards,

Sakari Ailus

\
 
 \ /
  Last update: 2020-04-04 01:29    [W:0.112 / U:34.504 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site