lkml.org 
[lkml]   [2020]   [Apr]   [26]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH 06/13] arm: dts: s5pv210: aries: Add support for more devices
Date
Add support for following devices:
- touchkeys connected over i2c-gpio
- s6e63m0 panel connected over spi-gpio
- fsa9480 microusb switch over i2c-gpio
- wm8994 over i2c-gpio (no machine driver yet)
- all common i2c-gpio devices

Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
---
arch/arm/boot/dts/s5pv210-aries.dtsi | 282 ++++++++++++++++++++--
arch/arm/boot/dts/s5pv210-fascinate4g.dts | 6 +
2 files changed, 270 insertions(+), 18 deletions(-)

diff --git a/arch/arm/boot/dts/s5pv210-aries.dtsi b/arch/arm/boot/dts/s5pv210-aries.dtsi
index f83df426f2b6..ef966d13d83d 100644
--- a/arch/arm/boot/dts/s5pv210-aries.dtsi
+++ b/arch/arm/boot/dts/s5pv210-aries.dtsi
@@ -12,8 +12,14 @@
compatible = "samsung,aries", "samsung,s5pv210";

aliases {
+ i2c4 = &i2c_sound;
+ i2c5 = &i2c_accel;
i2c6 = &i2c_pmic;
+ i2c7 = &i2c_musb;
i2c9 = &i2c_fuel;
+ i2c10 = &i2c_touchkey;
+ i2c11 = &i2c_prox;
+ i2c12 = &i2c_magnetometer;
};

memory@30000000 {
@@ -48,6 +54,18 @@
gpio = <&gpj1 1 GPIO_ACTIVE_HIGH>;
};

+ touchkey_vdd: regulator-fixed-1 {
+ compatible = "regulator-fixed";
+ regulator-name = "VTOUCH_3.3V";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ enable-active-high;
+ gpio = <&gpj3 2 GPIO_ACTIVE_HIGH>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&touchkey_vdd_ena>;
+ };
+
wifi_pwrseq: wifi-pwrseq {
compatible = "mmc-pwrseq-simple";
reset-gpios = <&gpg1 2 GPIO_ACTIVE_LOW>;
@@ -57,7 +75,69 @@
power-off-delay-us = <500>;
};

- i2c_pmic: i2c-gpio-0 {
+ i2c_sound: i2c-gpio-0 {
+ compatible = "i2c-gpio";
+ sda-gpios = <&mp05 3 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ scl-gpios = <&mp05 2 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ i2c-gpio,delay-us = <2>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&sound_i2c_pins>;
+
+ wm8994: wm8994@1a {
+ compatible = "wlf,wm8994";
+ reg = <0x1a>;
+
+ #sound-dai-cells = <0>;
+
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ clocks = <&clocks MOUT_CLKOUT>;
+ clock-names = "MCLK1";
+
+ AVDD2-supply = <&buck3_reg>;
+ DBVDD-supply = <&buck3_reg>;
+ CPVDD-supply = <&buck3_reg>;
+ SPKVDD1-supply = <&buck3_reg>;
+ SPKVDD2-supply = <&buck3_reg>;
+
+ wlf,gpio-cfg = <0xa101 0x8100 0x0100 0x0100 0x8100
+ 0xa101 0x0100 0x8100 0x0100 0x0100
+ 0x0100>;
+
+ wlf,ldo1ena = <&gpf3 4 GPIO_ACTIVE_HIGH>;
+ wlf,ldo2ena = <&gpf3 4 GPIO_ACTIVE_HIGH>;
+
+ wlf,lineout1-se;
+ wlf,lineout2-se;
+
+ assigned-clocks = <&clocks MOUT_CLKOUT>;
+ assigned-clock-rates = <0>;
+ assigned-clock-parents = <&xusbxti>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&codec_ldo>;
+ };
+ };
+
+ i2c_accel: i2c-gpio-1 {
+ compatible = "i2c-gpio";
+ sda-gpios = <&gpj3 6 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ scl-gpios = <&gpj3 7 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ i2c-gpio,delay-us = <2>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&accel_i2c_pins>;
+
+ /* bma023 accelerometer, no mainline binding */
+ };
+
+ i2c_pmic: i2c-gpio-2 {
compatible = "i2c-gpio";
sda-gpios = <&gpj4 0 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
scl-gpios = <&gpj4 3 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
@@ -137,8 +217,6 @@
regulator-name = "VLCD_1.8V";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
- /* Till we get panel driver */
- regulator-always-on;

regulator-state-mem {
regulator-off-in-suspend;
@@ -237,8 +315,6 @@
regulator-name = "VCC_3.0V_LCD";
regulator-min-microvolt = <3000000>;
regulator-max-microvolt = <3000000>;
- /* Till we get panel driver */
- regulator-always-on;

regulator-state-mem {
regulator-off-in-suspend;
@@ -309,7 +385,26 @@
};
};

- i2c_fuel: i2c-gpio-1 {
+ i2c_musb: i2c-gpio-3 {
+ compatible = "i2c-gpio";
+ sda-gpios = <&gpj3 4 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ scl-gpios = <&gpj3 5 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ i2c-gpio,delay-us = <2>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&musb_i2c_pins>;
+
+ fsa9480: musb@25 {
+ compatible = "fcs,fsa9480";
+ reg = <0x25>;
+ interrupt-parent = <&gph2>;
+ interrupts = <7 IRQ_TYPE_EDGE_FALLING>;
+ };
+ };
+
+ i2c_fuel: i2c-gpio-4 {
compatible = "i2c-gpio";
sda-gpios = <&mp05 1 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
scl-gpios = <&mp05 0 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
@@ -328,6 +423,60 @@
};
};

+ i2c_touchkey: i2c-gpio-5 {
+ compatible = "i2c-gpio";
+ sda-gpios = <&gpj3 0 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ scl-gpios = <&gpj3 1 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ i2c-gpio,delay-us = <2>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&touchkey_i2c_pins>;
+
+ touchkey@20 {
+ compatible = "cypress,aries-touchkey";
+ reg = <0x20>;
+ vdd-supply = <&touchkey_vdd>;
+ vcc-supply = <&buck3_reg>;
+ linux,keycodes = <KEY_MENU KEY_BACK
+ KEY_HOMEPAGE KEY_SEARCH>;
+ interrupt-parent = <&gpj4>;
+ interrupts = <1 IRQ_TYPE_LEVEL_LOW>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&touchkey_irq>;
+ };
+ };
+
+ i2c_prox: i2c-gpio-6 {
+ compatible = "i2c-gpio";
+ sda-gpios = <&gpg2 2 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ scl-gpios = <&gpg0 2 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ i2c-gpio,delay-us = <2>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&prox_i2c_pins>;
+
+ /* Sharp gp2a prox/light sensor, incomplete mainline binding */
+ };
+
+ i2c_magnetometer: i2c-gpio-7 {
+ compatible = "i2c-gpio";
+ sda-gpios = <&gpj0 1 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ scl-gpios = <&gpj0 0 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ i2c-gpio,delay-us = <2>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&magnetometer_i2c_pins>;
+
+ /* Yamaha yas529 magnetometer, no mainline binding */
+ };
+
vibrator: pwm-vibrator {
compatible = "pwm-vibrator";
pwms = <&pwm 1 44642 0>;
@@ -343,6 +492,39 @@
offset = <0x681c>; /* PS_HOLD_CONTROL */
value = <0x5200>;
};
+
+ spi_lcd: spi-gpio-0 {
+ compatible = "spi-gpio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ sck-gpios = <&mp04 1 GPIO_ACTIVE_HIGH>;
+ mosi-gpios = <&mp04 3 GPIO_ACTIVE_HIGH>;
+ cs-gpios = <&mp01 1 GPIO_ACTIVE_HIGH>;
+ num-chipselects = <1>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&lcd_spi_pins>;
+
+ panel@0 {
+ compatible = "samsung,s6e63m0";
+ reg = <0>;
+ reset-gpios = <&mp05 5 GPIO_ACTIVE_LOW>;
+ vdd3-supply = <&ldo7_reg>;
+ vci-supply = <&ldo17_reg>;
+ spi-cs-high;
+ spi-max-frequency = <1200000>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&panel_rst>;
+
+ port {
+ lcd_ep: endpoint {
+ remote-endpoint = <&fimd_ep>;
+ };
+ };
+ };
+ };
};

&fimd {
@@ -353,18 +535,13 @@
samsung,invert-vden;
samsung,invert-vclk;

- display-timings {
- timing-0 {
- /* 480x800@60Hz */
- clock-frequency = <25628040>;
- hactive = <480>;
- vactive = <800>;
- hfront-porch = <16>;
- hback-porch = <16>;
- hsync-len = <2>;
- vfront-porch = <28>;
- vback-porch = <1>;
- vsync-len = <2>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@3 {
+ reg = <3>;
+ fimd_ep: endpoint {
+ remote-endpoint = <&lcd_ep>;
};
};
};
@@ -405,6 +582,19 @@
samsung,pin-val = <1>;
};

+ codec_ldo: codec-ldo {
+ samsung,pins = "gpf3-4";
+ samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
+ samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
+ };
+
+ prox_i2c_pins: gp2a-i2c-pins {
+ samsung,pins = "gpg0-2", "gpg2-2";
+ samsung,pin-function = <EXYNOS_PIN_FUNC_F>;
+ samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
+ samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+ };
+
wlan_gpio_rst: wlan-gpio-rst {
samsung,pins = "gpg1-2";
samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
@@ -438,6 +628,13 @@
samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
};

+ magnetometer_i2c_pins: yas529-i2c-pins {
+ samsung,pins = "gpj0-0", "gpj0-1";
+ samsung,pin-function = <EXYNOS_PIN_FUNC_F>;
+ samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
+ samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+ };
+
ts_irq: ts-irq {
samsung,pins = "gpj0-5";
samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
@@ -445,17 +642,66 @@
samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
};

+ touchkey_i2c_pins: touchkey-i2c-pins {
+ samsung,pins = "gpj3-0", "gpj3-1";
+ samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
+ samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+ };
+
+ touchkey_vdd_ena: touchkey-vdd-ena {
+ samsung,pins = "gpj3-2";
+ samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
+ samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+ };
+
+ musb_i2c_pins: musb-i2c-pins {
+ samsung,pins = "gpj3-4", "gpj3-5";
+ samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
+ samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+ };
+
+ accel_i2c_pins: accel-i2c-pins {
+ samsung,pins = "gpj3-6", "gpj3-7";
+ samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
+ samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+ };
+
pmic_i2c_pins: pmic-i2c-pins {
samsung,pins = "gpj4-0", "gpj4-3";
samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
};

+ touchkey_irq: touchkey-irq {
+ samsung,pins = "gpj4-1";
+ samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
+ samsung,pin-pud = <S3C64XX_PIN_PULL_UP>;
+ samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+ };
+
+ lcd_spi_pins: spi-lcd-pins {
+ samsung,pins = "mp01-1", "mp04-1", "mp04-3";
+ samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
+ samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+ };
+
fg_i2c_pins: fg-i2c-pins {
samsung,pins = "mp05-0", "mp05-1";
samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
};
+
+ sound_i2c_pins: sound-i2c-pins {
+ samsung,pins = "mp05-2", "mp05-3";
+ samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
+ samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+ };
+
+ panel_rst: panel-rst {
+ samsung,pins = "mp05-5";
+ samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
+ samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+ };
};

&pwm {
diff --git a/arch/arm/boot/dts/s5pv210-fascinate4g.dts b/arch/arm/boot/dts/s5pv210-fascinate4g.dts
index 94dcb9b64b9a..42e6e2de197d 100644
--- a/arch/arm/boot/dts/s5pv210-fascinate4g.dts
+++ b/arch/arm/boot/dts/s5pv210-fascinate4g.dts
@@ -278,3 +278,9 @@
PIN_SLP(mp07-7, INPUT, DOWN);
};
};
+
+&wm8994 {
+ /* GPIO3 (BCLK2) and GPIO4 (LRCLK2) as outputs */
+ wlf,gpio-cfg = <0xa101 0x8100 0x8100 0x8100 0x8100 0xa101
+ 0x0100 0x8100 0x0100 0x0100 0x0100>;
+};
--
2.20.1
\
 
 \ /
  Last update: 2020-04-26 20:37    [W:0.114 / U:24.592 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site