lkml.org 
[lkml]   [2020]   [Mar]   [27]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Date
SubjectRe: [PATCH v4 2/2] iio: proximity: Add driver support for vcnl3020 proximity sensor
On Fri, Mar 27, 2020 at 12:49 PM Ivan Mikhaylov <i.mikhaylov@yadro.com> wrote:
>
> Proximity sensor driver based on light/vcnl4000.c code.
> For now supports only the single on-demand measurement.
>
> The VCNL3020 is a fully integrated proximity sensor. Fully
> integrated means that the infrared emitter is included in the
> package. It has 16-bit resolution. It includes a signal
> processing IC and features standard I2C communication
> interface. It features an interrupt function.

(When somebody gives you a tag and you are about to send new version
without [drastical] changes, don't forget to add it to your patch)

One nit below, after addressing,
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>

> Datasheet: http://www.vishay.com/docs/84150/vcnl3020.pdf
> Signed-off-by: Ivan Mikhaylov <i.mikhaylov@yadro.com>
> ---
> drivers/iio/proximity/Kconfig | 11 ++
> drivers/iio/proximity/Makefile | 1 +
> drivers/iio/proximity/vcnl3020.c | 232 +++++++++++++++++++++++++++++++
> 3 files changed, 244 insertions(+)
> create mode 100644 drivers/iio/proximity/vcnl3020.c
>
> diff --git a/drivers/iio/proximity/Kconfig b/drivers/iio/proximity/Kconfig
> index d53601447da4..b8d2b17e60ac 100644
> --- a/drivers/iio/proximity/Kconfig
> +++ b/drivers/iio/proximity/Kconfig
> @@ -112,6 +112,17 @@ config SRF08
> To compile this driver as a module, choose M here: the
> module will be called srf08.
>
> +config VCNL3020
> + tristate "VCNL3020 proximity sensor"
> + select REGMAP_I2C
> + depends on I2C
> + help
> + Say Y here if you want to build a driver for the Vishay VCNL3020
> + proximity sensor.
> +
> + To compile this driver as a module, choose M here: the
> + module will be called vcnl3020.
> +
> config VL53L0X_I2C
> tristate "STMicroelectronics VL53L0X ToF ranger sensor (I2C)"
> depends on I2C
> diff --git a/drivers/iio/proximity/Makefile b/drivers/iio/proximity/Makefile
> index 0bb5f9de13d6..8245978ced30 100644
> --- a/drivers/iio/proximity/Makefile
> +++ b/drivers/iio/proximity/Makefile
> @@ -12,5 +12,6 @@ obj-$(CONFIG_RFD77402) += rfd77402.o
> obj-$(CONFIG_SRF04) += srf04.o
> obj-$(CONFIG_SRF08) += srf08.o
> obj-$(CONFIG_SX9500) += sx9500.o
> +obj-$(CONFIG_VCNL3020) += vcnl3020.o
> obj-$(CONFIG_VL53L0X_I2C) += vl53l0x-i2c.o
>
> diff --git a/drivers/iio/proximity/vcnl3020.c b/drivers/iio/proximity/vcnl3020.c
> new file mode 100644
> index 000000000000..fcde509238f9
> --- /dev/null
> +++ b/drivers/iio/proximity/vcnl3020.c
> @@ -0,0 +1,232 @@
> +// SPDX-License-Identifier: GPL-2.0-only
> +/*
> + * Support for Vishay VCNL3020 proximity sensor on i2c bus.
> + * Based on Vishay VCNL4000 driver code.
> + *
> + * TODO: interrupts.
> + */
> +
> +#include <linux/module.h>
> +#include <linux/i2c.h>
> +#include <linux/err.h>
> +#include <linux/delay.h>
> +#include <linux/regmap.h>
> +
> +#include <linux/iio/iio.h>
> +#include <linux/iio/sysfs.h>
> +
> +#define VCNL_DRV_NAME "vcnl3020"
> +#define VCNL_REGMAP_NAME "vcnl3020_regmap"
> +#define VCNL3020_PROD_ID 0x21
> +
> +#define VCNL_COMMAND 0x80 /* Command register */
> +#define VCNL_PROD_REV 0x81 /* Product ID and Revision ID */
> +#define VCNL_PROXIMITY_RATE 0x82 /* Rate of Proximity Measurement */
> +#define VCNL_LED_CURRENT 0x83 /* IR LED current for proximity mode */
> +#define VCNL_PS_RESULT_HI 0x87 /* Proximity result register, MSB */
> +#define VCNL_PS_RESULT_LO 0x88 /* Proximity result register, LSB */
> +#define VCNL_PS_ICR 0x89 /* Interrupt Control Register */
> +
> +#define VCNL_PS_LO_THR_HI 0x8a /* High byte of low threshold value */
> +#define VCNL_PS_LO_THR_LO 0x8b /* Low byte of low threshold value */
> +#define VCNL_PS_HI_THR_HI 0x8c /* High byte of high threshold value */
> +#define VCNL_PS_HI_THR_LO 0x8d /* Low byte of high threshold value */
> +#define VCNL_ISR 0x8e /* Interrupt Status Register */
> +#define VCNL_PS_MOD_ADJ 0x8f /* Proximity Modulator Timing Adjustment */
> +
> +/* Bit masks for COMMAND register */
> +#define VCNL_PS_RDY BIT(5) /* proximity data ready? */
> +#define VCNL_PS_OD BIT(3) /* start on-demand proximity
> + * measurement
> + */
> +
> +#define VCNL_ON_DEMAND_TIMEOUT_US 100000
> +#define VCNL_POLL_US 20000
> +
> +struct vcnl3020_data {
> + struct regmap *regmap;
> + struct device *dev;
> + u8 rev;
> + struct mutex lock;
> +};
> +
> +static int vcnl3020_init(struct vcnl3020_data *data)
> +{
> + int rc;
> + unsigned int reg;
> + u32 led_current;
> +
> + rc = device_property_read_u32(data->dev, "led-current", &led_current);
> + if (rc) {
> + dev_err(data->dev, "Couldn't get led current (%d)", rc);
> + return rc;
> + }
> +
> + rc = regmap_read(data->regmap, VCNL_PROD_REV, &reg);
> + if (rc) {
> + dev_err(data->dev,
> + "Error (%d) reading product revision", rc);
> + return rc;
> + }
> +
> + if (reg != VCNL3020_PROD_ID) {
> + dev_err(data->dev,
> + "Product id (%x) did not match vcnl3020 (%x)", reg,
> + VCNL3020_PROD_ID);
> + return -ENODEV;

> + } else {
> + data->rev = reg;
> + mutex_init(&data->lock);
> + }

As I have told you before the 'else' now is redundant, you may put the
code as mainstream flow here.

> + /* set led current */
> + rc = regmap_write(data->regmap, VCNL_LED_CURRENT, led_current);
> + if (rc)
> + dev_err(data->dev, "Error (%d) setting LED current", rc);
> +
> + return rc;
> +};
> +
> +static int vcnl3020_measure_proximity(struct vcnl3020_data *data, int *val)
> +{
> + int rc;
> + unsigned int reg;
> + unsigned int hi, lo;
> +
> + mutex_lock(&data->lock);
> +
> + rc = regmap_write(data->regmap, VCNL_COMMAND, VCNL_PS_OD);
> + if (rc)
> + goto err_unlock;
> +
> + /* wait for data to become ready */
> + rc = regmap_read_poll_timeout(data->regmap, VCNL_COMMAND, reg,
> + reg & VCNL_PS_RDY, VCNL_POLL_US,
> + VCNL_ON_DEMAND_TIMEOUT_US);
> + if (rc) {
> + dev_err(data->dev,
> + "vcnl3020_measure() failed, data is not ready");
> + goto err_unlock;
> + }
> +
> + rc = regmap_read(data->regmap, VCNL_PS_RESULT_HI, &hi);
> + if (rc)
> + goto err_unlock;
> + dev_dbg(data->dev, "result high byte 0x%x", hi);
> +
> + rc = regmap_read(data->regmap, VCNL_PS_RESULT_LO, &lo);
> + if (rc)
> + goto err_unlock;
> + dev_dbg(data->dev, "result low byte 0x%x", lo);
> + *val = (hi << 8) | lo;
> +
> +err_unlock:
> + mutex_unlock(&data->lock);
> +
> + return rc;
> +}
> +
> +static const struct iio_chan_spec vcnl3020_channels[] = {
> + {
> + .type = IIO_PROXIMITY,
> + .info_mask_separate = BIT(IIO_CHAN_INFO_RAW),
> + },
> +};
> +
> +static int vcnl3020_read_raw(struct iio_dev *indio_dev,
> + struct iio_chan_spec const *chan, int *val,
> + int *val2, long mask)
> +{
> + int rc;
> + struct vcnl3020_data *data = iio_priv(indio_dev);
> +
> + switch (mask) {
> + case IIO_CHAN_INFO_RAW:
> + switch (chan->type) {
> + case IIO_PROXIMITY:
> + rc = vcnl3020_measure_proximity(data, val);
> + if (rc)
> + return rc;
> + return IIO_VAL_INT;
> + default:
> + return -EINVAL;
> + }
> + default:
> + return -EINVAL;
> + }
> +}
> +
> +static const struct iio_info vcnl3020_info = {
> + .read_raw = vcnl3020_read_raw,
> +};
> +
> +static const struct regmap_config vcnl3020_regmap_config = {
> + .name = VCNL_REGMAP_NAME,
> + .reg_bits = 8,
> + .val_bits = 8,
> + .max_register = VCNL_PS_MOD_ADJ,
> +};
> +
> +static int vcnl3020_probe(struct i2c_client *client)
> +{
> + struct vcnl3020_data *data;
> + struct iio_dev *indio_dev;
> + struct regmap *regmap;
> + int rc;
> +
> + regmap = devm_regmap_init_i2c(client, &vcnl3020_regmap_config);
> + if (IS_ERR(regmap)) {
> + dev_err(&client->dev, "regmap_init failed!");
> + return PTR_ERR(regmap);
> + }
> +
> + indio_dev = devm_iio_device_alloc(&client->dev, sizeof(*data));
> + if (!indio_dev)
> + return -ENOMEM;
> +
> + data = iio_priv(indio_dev);
> + i2c_set_clientdata(client, indio_dev);
> + data->regmap = regmap;
> + data->dev = &client->dev;
> +
> + rc = vcnl3020_init(data);
> + if (rc)
> + return rc;
> +
> + indio_dev->dev.parent = &client->dev;
> + indio_dev->info = &vcnl3020_info;
> + indio_dev->channels = vcnl3020_channels;
> + indio_dev->num_channels = ARRAY_SIZE(vcnl3020_channels);
> + indio_dev->name = VCNL_DRV_NAME;
> + indio_dev->modes = INDIO_DIRECT_MODE;
> +
> + return devm_iio_device_register(&client->dev, indio_dev);
> +}
> +
> +static const struct i2c_device_id vcnl3020_id[] = {
> + { "vcnl3020", 0 },
> + {}
> +};
> +MODULE_DEVICE_TABLE(i2c, vcnl3020_id);
> +
> +static const struct of_device_id vcnl3020_of_match[] = {
> + {
> + .compatible = "vishay,vcnl3020",
> + },
> + {}
> +};
> +MODULE_DEVICE_TABLE(of, vcnl3020_of_match);
> +
> +static struct i2c_driver vcnl3020_driver = {
> + .driver = {
> + .name = VCNL_DRV_NAME,
> + .of_match_table = vcnl3020_of_match,
> + },
> + .probe_new = vcnl3020_probe,
> + .id_table = vcnl3020_id,
> +};
> +module_i2c_driver(vcnl3020_driver);
> +
> +MODULE_AUTHOR("Ivan Mikhaylov <i.mikhaylov@yadro.com>");
> +MODULE_DESCRIPTION("Vishay VCNL3020 proximity sensor driver");
> +MODULE_LICENSE("GPL");
> --
> 2.21.1
>


--
With Best Regards,
Andy Shevchenko

\
 
 \ /
  Last update: 2020-03-27 12:13    [W:0.112 / U:3.560 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site