[lkml]   [2020]   [Mar]   [24]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
Messages in this thread
Subject[PATCH 00/13] usb: dwc3: meson: add OTG support for GXL/GXM
The USB support was initialy done with a set of PHYs and dwc3-of-simple
because the architecture of the USB complex was not understood correctly
at the time (and proper documentation was missing...).

But with the G12A family, the USB complex was correctly understood and
implemented correctly.
But seems the G12A architecture was derived for the GXL USB architecture,
with minor differences and looks we can share most of the USB DWC3 glue

This patchset refactors and adds callbacks to handle the architecture
difference while keeping the main code shared.

The main difference is that on GXL/GXM the USB2 PHY control registers
are mixed with the PHY registers (we already handle correctly), and
the GLUE registers are allmost (99%) the same as G12A.

But, the GXL/GXM HW is buggy, here are the quirks :
- for the DWC2 controller to reset correctly, the GLUE mux must be switched
to peripheral when the DWC2 controlle probes. For now it's handled by simply
switching to device when probing the subnodes, but it may be not enough
- when manually switching from Host to Device when the USB port is not
populated (should not happen with proper Micro-USB/USB-C OTG switch), it
makes the DWC3 to crash. The only way to avoid that is to use the Host
Disconnect bit to disconnect the DWC3 controller from the port, but we can't
recover the Host functionnality unless resetting the DWC3 controller.
This bit is set when only manual switch is done, and a warning is printed
on manual switching.

The patches 1-8 should be applied first, then either waiting the next release
or if the usb maintainer can provide us a stable tag, we can use it to merge
the DT and bindings.

Martin Blumenstingl (4):
arm64: dts: amlogic: use the new USB control driver for GXL and GXM
phy: amlogic: meson-gxl-usb3: remove code for non-existing PHY
usb: dwc3: of-simple: remove Amlogic GXL and AXG compatibles
dt-bindings: usb: dwc3: remove old DWC3 wrapper

Neil Armstrong (9):
dt-bindings: usb: amlogic,meson-g12a-usb-ctrl: add the Amlogic GXL and
GXM Families USB Glue Bindings
usb: dwc3: meson-g12a: specify phy names in soc data
usb: dwc3: meson-g12a: handle the phy and glue registers separately
usb: dwc3: meson-g12a: get the reset as shared
usb: dwc3: meson-g12a: refactor usb2 phy init
usb: dwc3: meson-g12a: refactor usb init
usb: dwc3: meson-g12a: support the GXL/GXM DWC3 host phy disconnect
usb: dwc3: meson-g12a: add support for GXL and GXM SoCs
doc: dt: bindings: usb: dwc3: remove amlogic compatible entries

.../bindings/phy/meson-gxl-usb3-phy.txt | 31 --
.../devicetree/bindings/usb/amlogic,dwc3.txt | 42 --
.../usb/amlogic,meson-g12a-usb-ctrl.yaml | 21 +
.../devicetree/bindings/usb/dwc3.txt | 2 -
.../dts/amlogic/meson-gx-libretech-pc.dtsi | 2 +-
.../boot/dts/amlogic/meson-gx-p23x-q20x.dtsi | 2 +-
.../amlogic/meson-gxl-s805x-libretech-ac.dts | 3 +-
.../boot/dts/amlogic/meson-gxl-s805x-p241.dts | 3 +-
.../amlogic/meson-gxl-s905d-phicomm-n1.dts | 4 +
.../boot/dts/amlogic/meson-gxl-s905w-p281.dts | 4 +
.../dts/amlogic/meson-gxl-s905w-tx3-mini.dts | 4 +
.../amlogic/meson-gxl-s905x-khadas-vim.dts | 4 +
.../amlogic/meson-gxl-s905x-libretech-cc.dts | 7 +-
.../amlogic/meson-gxl-s905x-nexbox-a95x.dts | 3 +-
.../dts/amlogic/meson-gxl-s905x-p212.dtsi | 7 +-
arch/arm64/boot/dts/amlogic/meson-gxl.dtsi | 45 +-
.../dts/amlogic/meson-gxm-khadas-vim2.dts | 3 +-
.../boot/dts/amlogic/meson-gxm-nexbox-a1.dts | 3 +-
.../boot/dts/amlogic/meson-gxm-vega-s96.dts | 4 +
arch/arm64/boot/dts/amlogic/meson-gxm.dtsi | 7 +-
drivers/phy/amlogic/Kconfig | 12 -
drivers/phy/amlogic/Makefile | 1 -
drivers/phy/amlogic/phy-meson-gxl-usb3.c | 283 ------------
drivers/usb/dwc3/dwc3-meson-g12a.c | 407 ++++++++++++++----
drivers/usb/dwc3/dwc3-of-simple.c | 30 +-
25 files changed, 421 insertions(+), 513 deletions(-)
delete mode 100644 Documentation/devicetree/bindings/phy/meson-gxl-usb3-phy.txt
delete mode 100644 Documentation/devicetree/bindings/usb/amlogic,dwc3.txt
delete mode 100644 drivers/phy/amlogic/phy-meson-gxl-usb3.c


 \ /
  Last update: 2020-03-24 11:22    [W:0.160 / U:0.392 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site