[lkml]   [2020]   [Mar]   [2]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
Messages in this thread
Patch in this message
Subject[PATCH 26/42] docs: scsi: convert qlogicfas.txt to ReST
Signed-off-by: Mauro Carvalho Chehab <>
Documentation/scsi/index.rst | 1 +
.../scsi/{qlogicfas.txt => qlogicfas.rst} | 17 +++++++++++++----
drivers/scsi/Kconfig | 2 +-
3 files changed, 15 insertions(+), 5 deletions(-)
rename Documentation/scsi/{qlogicfas.txt => qlogicfas.rst} (92%)

diff --git a/Documentation/scsi/index.rst b/Documentation/scsi/index.rst
index 17327f67af68..29e211ee9145 100644
--- a/Documentation/scsi/index.rst
+++ b/Documentation/scsi/index.rst
@@ -30,5 +30,6 @@ Linux SCSI Subsystem
+ qlogicfas

diff --git a/Documentation/scsi/qlogicfas.txt b/Documentation/scsi/qlogicfas.rst
similarity index 92%
rename from Documentation/scsi/qlogicfas.txt
rename to Documentation/scsi/qlogicfas.rst
index c211d827fef2..b17f1b3676c3 100644
--- a/Documentation/scsi/qlogicfas.txt
+++ b/Documentation/scsi/qlogicfas.rst
@@ -1,3 +1,8 @@
+.. SPDX-License-Identifier: GPL-2.0
+Qlogic FASXXX Family Driver Notes

This driver supports the Qlogic FASXXX family of chips. This driver
only works with the ISA, VLB, and PCMCIA versions of the Qlogic
@@ -16,7 +21,8 @@ is provided by the qla1280 driver.
Nor does it support the PCI-Basic, which is supported by the
'am53c974' driver.

+PCMCIA Support

This currently only works if the card is enabled first from DOS. This
means you will have to load your socket and card services, and
@@ -31,7 +37,8 @@ it from configuring the card.
I am working with the PCMCIA group to make it more flexible, but that
may take a while.

+All Cards

The top of the qlogic.c file has a number of defines that controls
configuration. As shipped, it provides a balance between speed and
@@ -46,7 +53,8 @@ command or something. It comes up faster if this is set to zero, and
if you have reliable hardware and connections it may be more useful to
not reset things.

+Some Troubleshooting Tips

Make sure it works properly under DOS. You should also do an initial FDISK
on a new drive if you want partitions.
@@ -54,7 +62,8 @@ on a new drive if you want partitions.
Don't enable all the speedups first. If anything is wrong, they will make
any problem worse.


The best way to test if your cables, termination, etc. are good is to
copy a very big file (e.g. a doublespace container file, or a very
diff --git a/drivers/scsi/Kconfig b/drivers/scsi/Kconfig
index 82462d6a4ce5..d34c682e94cf 100644
--- a/drivers/scsi/Kconfig
+++ b/drivers/scsi/Kconfig
@@ -1117,7 +1117,7 @@ config SCSI_QLOGIC_FAS
SCSI support"), below.

Information about this driver is contained in
- <file:Documentation/scsi/qlogicfas.txt>. You should also read the
+ <file:Documentation/scsi/qlogicfas.rst>. You should also read the
SCSI-HOWTO, available from

 \ /
  Last update: 2020-03-02 09:18    [W:0.369 / U:0.752 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site