lkml.org 
[lkml]   [2020]   [Mar]   [10]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
SubjectRe: [PATCH] ARM: dts: dra7: Add bus_dma_limit for L3 bus
From
Date
On 10/03/2020 13:53, Roger Quadros wrote:
> The L3 interconnect can access only 32-bits of address.
> Add the dma-ranges property to reflect this limit.
>
> This will ensure that no device under L3 is
> given > 32-bit address for DMA.
>
> Issue was observed only with SATA on DRA7-EVM with 4GB RAM
> and CONFIG_ARM_LPAE enabled. This is because the controller
> can perform 64-bit DMA and was setting the dma_mask to 64-bit.
>
> Setting the correct bus_dma_limit fixes the issue.

This seems kind of messy to modify almost every DT node because of
this.... Are you sure this is the only way to get it done? No way to
modify the sata node only which is impacted somehow?

Also, what if you just pass 0xffffffff to the dma-ranges property? That
would avoid modifying every node I guess.

-Tero

>
> Signed-off-by: Roger Quadros <rogerq@ti.com>
> ---
> arch/arm/boot/dts/dra7-l4.dtsi | 20 ++---
> arch/arm/boot/dts/dra7.dtsi | 129 +++++++++++++++++----------------
> arch/arm/boot/dts/dra72x.dtsi | 6 +-
> arch/arm/boot/dts/dra74x.dtsi | 33 +++++----
> 4 files changed, 95 insertions(+), 93 deletions(-)
>
> diff --git a/arch/arm/boot/dts/dra7-l4.dtsi b/arch/arm/boot/dts/dra7-l4.dtsi
> index fc418834890d..5bbe3de7eba3 100644
> --- a/arch/arm/boot/dts/dra7-l4.dtsi
> +++ b/arch/arm/boot/dts/dra7-l4.dtsi
> @@ -2280,11 +2280,11 @@
>
> &l4_per2 { /* 0x48400000 */
> compatible = "ti,dra7-l4-per2", "simple-bus";
> - reg = <0x48400000 0x800>,
> - <0x48400800 0x800>,
> - <0x48401000 0x400>,
> - <0x48401400 0x400>,
> - <0x48401800 0x400>;
> + reg = <0x48400000 0x0 0x800>,
> + <0x48400800 0x0 0x800>,
> + <0x48401000 0x0 0x400>,
> + <0x48401400 0x0 0x400>,
> + <0x48401800 0x0 0x400>;
> reg-names = "ap", "la", "ia0", "ia1", "ia2";
> #address-cells = <1>;
> #size-cells = <1>;
> @@ -3152,11 +3152,11 @@
>
> &l4_per3 { /* 0x48800000 */
> compatible = "ti,dra7-l4-per3", "simple-bus";
> - reg = <0x48800000 0x800>,
> - <0x48800800 0x800>,
> - <0x48801000 0x400>,
> - <0x48801400 0x400>,
> - <0x48801800 0x400>;
> + reg = <0x48800000 0x0 0x800>,
> + <0x48800800 0x0 0x800>,
> + <0x48801000 0x0 0x400>,
> + <0x48801400 0x0 0x400>,
> + <0x48801800 0x0 0x400>;
> reg-names = "ap", "la", "ia0", "ia1", "ia2";
> #address-cells = <1>;
> #size-cells = <1>;
> diff --git a/arch/arm/boot/dts/dra7.dtsi b/arch/arm/boot/dts/dra7.dtsi
> index d78b684e7fca..81e7f30afe02 100644
> --- a/arch/arm/boot/dts/dra7.dtsi
> +++ b/arch/arm/boot/dts/dra7.dtsi
> @@ -146,8 +146,9 @@
> ocp {
> compatible = "ti,dra7-l3-noc", "simple-bus";
> #address-cells = <1>;
> - #size-cells = <1>;
> - ranges = <0x0 0x0 0x0 0xc0000000>;
> + #size-cells = <2>;
> + ranges = <0x0 0x0 0x0 0x0 0xc0000000>;
> + dma-ranges = <0x0 0x0 0x0 0x1 0x00000000>;
> ti,hwmods = "l3_main_1", "l3_main_2";
> reg = <0x0 0x44000000 0x0 0x1000000>,
> <0x0 0x45000000 0x0 0x1000>;
> @@ -261,7 +262,7 @@
>
> ocmcram1: ocmcram@40300000 {
> compatible = "mmio-sram";
> - reg = <0x40300000 0x80000>;
> + reg = <0x40300000 0x0 0x80000>;
> ranges = <0x0 0x40300000 0x80000>;
> #address-cells = <1>;
> #size-cells = <1>;
> @@ -291,7 +292,7 @@
> ocmcram2: ocmcram@40400000 {
> status = "disabled";
> compatible = "mmio-sram";
> - reg = <0x40400000 0x100000>;
> + reg = <0x40400000 0x0 0x100000>;
> ranges = <0x0 0x40400000 0x100000>;
> #address-cells = <1>;
> #size-cells = <1>;
> @@ -300,19 +301,19 @@
> ocmcram3: ocmcram@40500000 {
> status = "disabled";
> compatible = "mmio-sram";
> - reg = <0x40500000 0x100000>;
> + reg = <0x40500000 0x0 0x100000>;
> ranges = <0x0 0x40500000 0x100000>;
> #address-cells = <1>;
> #size-cells = <1>;
> };
>
> bandgap: bandgap@4a0021e0 {
> - reg = <0x4a0021e0 0xc
> - 0x4a00232c 0xc
> - 0x4a002380 0x2c
> - 0x4a0023C0 0x3c
> - 0x4a002564 0x8
> - 0x4a002574 0x50>;
> + reg = <0x4a0021e0 0x0 0xc
> + 0x4a00232c 0x0 0xc
> + 0x4a002380 0x0 0x2c
> + 0x4a0023C0 0x0 0x3c
> + 0x4a002564 0x0 0x8
> + 0x4a002574 0x0 0x50>;
> compatible = "ti,dra752-bandgap";
> interrupts = <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>;
> #thermal-sensor-cells = <1>;
> @@ -320,12 +321,12 @@
>
> dsp1_system: dsp_system@40d00000 {
> compatible = "syscon";
> - reg = <0x40d00000 0x100>;
> + reg = <0x40d00000 0x0 0x100>;
> };
>
> dra7_iodelay_core: padconf@4844a000 {
> compatible = "ti,dra7-iodelay";
> - reg = <0x4844a000 0x0d1c>;
> + reg = <0x4844a000 0x0 0x0d1c>;
> #address-cells = <1>;
> #size-cells = <0>;
> #pinctrl-cells = <2>;
> @@ -334,7 +335,7 @@
> edma: edma@43300000 {
> compatible = "ti,edma3-tpcc";
> ti,hwmods = "tpcc";
> - reg = <0x43300000 0x100000>;
> + reg = <0x43300000 0x0 0x100000>;
> reg-names = "edma3_cc";
> interrupts = <GIC_SPI 361 IRQ_TYPE_LEVEL_HIGH>,
> <GIC_SPI 360 IRQ_TYPE_LEVEL_HIGH>,
> @@ -357,7 +358,7 @@
> edma_tptc0: tptc@43400000 {
> compatible = "ti,edma3-tptc";
> ti,hwmods = "tptc0";
> - reg = <0x43400000 0x100000>;
> + reg = <0x43400000 0x0 0x100000>;
> interrupts = <GIC_SPI 370 IRQ_TYPE_LEVEL_HIGH>;
> interrupt-names = "edma3_tcerrint";
> };
> @@ -365,23 +366,23 @@
> edma_tptc1: tptc@43500000 {
> compatible = "ti,edma3-tptc";
> ti,hwmods = "tptc1";
> - reg = <0x43500000 0x100000>;
> + reg = <0x43500000 0x0 0x100000>;
> interrupts = <GIC_SPI 371 IRQ_TYPE_LEVEL_HIGH>;
> interrupt-names = "edma3_tcerrint";
> };
>
> dmm@4e000000 {
> compatible = "ti,omap5-dmm";
> - reg = <0x4e000000 0x800>;
> + reg = <0x4e000000 0x0 0x800>;
> interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>;
> ti,hwmods = "dmm";
> };
>
> target-module@40d01000 {
> compatible = "ti,sysc-omap2", "ti,sysc";
> - reg = <0x40d01000 0x4>,
> - <0x40d01010 0x4>,
> - <0x40d01014 0x4>;
> + reg = <0x40d01000 0x0 0x4>,
> + <0x40d01010 0x0 0x4>,
> + <0x40d01014 0x0 0x4>;
> reg-names = "rev", "sysc", "syss";
> ti,sysc-sidle = <SYSC_IDLE_FORCE>,
> <SYSC_IDLE_NO>,
> @@ -408,9 +409,9 @@
>
> target-module@40d02000 {
> compatible = "ti,sysc-omap2", "ti,sysc";
> - reg = <0x40d02000 0x4>,
> - <0x40d02010 0x4>,
> - <0x40d02014 0x4>;
> + reg = <0x40d02000 0x0 0x4>,
> + <0x40d02010 0x0 0x4>,
> + <0x40d02014 0x0 0x4>;
> reg-names = "rev", "sysc", "syss";
> ti,sysc-sidle = <SYSC_IDLE_FORCE>,
> <SYSC_IDLE_NO>,
> @@ -437,9 +438,9 @@
>
> target-module@58882000 {
> compatible = "ti,sysc-omap2", "ti,sysc";
> - reg = <0x58882000 0x4>,
> - <0x58882010 0x4>,
> - <0x58882014 0x4>;
> + reg = <0x58882000 0x0 0x4>,
> + <0x58882010 0x0 0x4>,
> + <0x58882014 0x0 0x4>;
> reg-names = "rev", "sysc", "syss";
> ti,sysc-sidle = <SYSC_IDLE_FORCE>,
> <SYSC_IDLE_NO>,
> @@ -466,9 +467,9 @@
>
> target-module@55082000 {
> compatible = "ti,sysc-omap2", "ti,sysc";
> - reg = <0x55082000 0x4>,
> - <0x55082010 0x4>,
> - <0x55082014 0x4>;
> + reg = <0x55082000 0x0 0x4>,
> + <0x55082010 0x0 0x4>,
> + <0x55082014 0x0 0x4>;
> reg-names = "rev", "sysc", "syss";
> ti,sysc-sidle = <SYSC_IDLE_FORCE>,
> <SYSC_IDLE_NO>,
> @@ -502,9 +503,9 @@
> ti,settling-time = <50>;
> ti,clock-cycles = <16>;
>
> - reg = <0x4ae07ddc 0x4>, <0x4ae07de0 0x4>,
> - <0x4ae06014 0x4>, <0x4a003b20 0xc>,
> - <0x4ae0c158 0x4>;
> + reg = <0x4ae07ddc 0x0 0x4>, <0x4ae07de0 0x0 0x4>,
> + <0x4ae06014 0x0 0x4>, <0x4a003b20 0x0 0xc>,
> + <0x4ae0c158 0x0 0x4>;
> reg-names = "setup-address", "control-address",
> "int-address", "efuse-address",
> "ldo-address";
> @@ -535,9 +536,9 @@
> ti,settling-time = <50>;
> ti,clock-cycles = <16>;
>
> - reg = <0x4ae07e34 0x4>, <0x4ae07e24 0x4>,
> - <0x4ae06010 0x4>, <0x4a0025cc 0xc>,
> - <0x4a002470 0x4>;
> + reg = <0x4ae07e34 0x0 0x4>, <0x4ae07e24 0x0 0x4>,
> + <0x4ae06010 0x0 0x4>, <0x4a0025cc 0x0 0xc>,
> + <0x4a002470 0x0 0x4>;
> reg-names = "setup-address", "control-address",
> "int-address", "efuse-address",
> "ldo-address";
> @@ -568,9 +569,9 @@
> ti,settling-time = <50>;
> ti,clock-cycles = <16>;
>
> - reg = <0x4ae07e30 0x4>, <0x4ae07e20 0x4>,
> - <0x4ae06010 0x4>, <0x4a0025e0 0xc>,
> - <0x4a00246c 0x4>;
> + reg = <0x4ae07e30 0x0 0x4>, <0x4ae07e20 0x0 0x4>,
> + <0x4ae06010 0x0 0x4>, <0x4a0025e0 0x0 0xc>,
> + <0x4a00246c 0x0 0x4>;
> reg-names = "setup-address", "control-address",
> "int-address", "efuse-address",
> "ldo-address";
> @@ -601,9 +602,9 @@
> ti,settling-time = <50>;
> ti,clock-cycles = <16>;
>
> - reg = <0x4ae07de4 0x4>, <0x4ae07de8 0x4>,
> - <0x4ae06010 0x4>, <0x4a003b08 0xc>,
> - <0x4ae0c154 0x4>;
> + reg = <0x4ae07de4 0x0 0x4>, <0x4ae07de8 0x0 0x4>,
> + <0x4ae06010 0x0 0x4>, <0x4a003b08 0x0 0xc>,
> + <0x4ae0c154 0x0 0x4>;
> reg-names = "setup-address", "control-address",
> "int-address", "efuse-address",
> "ldo-address";
> @@ -627,8 +628,8 @@
>
> qspi: spi@4b300000 {
> compatible = "ti,dra7xxx-qspi";
> - reg = <0x4b300000 0x100>,
> - <0x5c000000 0x4000000>;
> + reg = <0x4b300000 0x0 0x100>,
> + <0x5c000000 0x0 0x4000000>;
> reg-names = "qspi_base", "qspi_mmap";
> syscon-chipselects = <&scm_conf 0x558>;
> #address-cells = <1>;
> @@ -644,7 +645,7 @@
> /* OCP2SCP3 */
> sata: sata@4a141100 {
> compatible = "snps,dwc-ahci";
> - reg = <0x4a140000 0x1100>, <0x4a141100 0x7>;
> + reg = <0x4a140000 0x0 0x1100>, <0x4a141100 0x0 0x7>;
> interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>;
> phys = <&sata_phy>;
> phy-names = "sata-phy";
> @@ -658,7 +659,7 @@
> gpmc: gpmc@50000000 {
> compatible = "ti,am3352-gpmc";
> ti,hwmods = "gpmc";
> - reg = <0x50000000 0x37c>; /* device IO registers */
> + reg = <0x50000000 0x0 0x37c>; /* device IO registers */
> interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>;
> dmas = <&edma_xbar 4 0>;
> dma-names = "rxtx";
> @@ -675,8 +676,8 @@
>
> target-module@56000000 {
> compatible = "ti,sysc-omap4", "ti,sysc";
> - reg = <0x5600fe00 0x4>,
> - <0x5600fe10 0x4>;
> + reg = <0x5600fe00 0x0 0x4>,
> + <0x5600fe10 0x0 0x4>;
> reg-names = "rev", "sysc";
> ti,sysc-midle = <SYSC_IDLE_FORCE>,
> <SYSC_IDLE_NO>,
> @@ -693,7 +694,7 @@
>
> crossbar_mpu: crossbar@4a002a48 {
> compatible = "ti,irq-crossbar";
> - reg = <0x4a002a48 0x130>;
> + reg = <0x4a002a48 0x0 0x130>;
> interrupt-controller;
> interrupt-parent = <&wakeupgen>;
> #interrupt-cells = <3>;
> @@ -715,11 +716,11 @@
> syscon-pll-ctrl = <&scm_conf 0x538>;
> #address-cells = <1>;
> #size-cells = <1>;
> - ranges;
> + ranges = <0x0 0x58000000 0x79000>;
>
> dispc@58001000 {
> compatible = "ti,dra7-dispc";
> - reg = <0x58001000 0x1000>;
> + reg = <0x1000 0x1000>;
> interrupts = <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>;
> ti,hwmods = "dss_dispc";
> clocks = <&dss_clkctrl DRA7_DSS_DSS_CORE_CLKCTRL 8>;
> @@ -730,10 +731,10 @@
>
> hdmi: encoder@58060000 {
> compatible = "ti,dra7-hdmi";
> - reg = <0x58040000 0x200>,
> - <0x58040200 0x80>,
> - <0x58040300 0x80>,
> - <0x58060000 0x19000>;
> + reg = <0x40000 0x200>,
> + <0x40200 0x80>,
> + <0x40300 0x80>,
> + <0x60000 0x19000>;
> reg-names = "wp", "pll", "phy", "core";
> interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
> status = "disabled";
> @@ -748,9 +749,9 @@
>
> aes1_target: target-module@4b500000 {
> compatible = "ti,sysc-omap2", "ti,sysc";
> - reg = <0x4b500080 0x4>,
> - <0x4b500084 0x4>,
> - <0x4b500088 0x4>;
> + reg = <0x4b500080 0x0 0x4>,
> + <0x4b500084 0x0 0x4>,
> + <0x4b500088 0x0 0x4>;
> reg-names = "rev", "sysc", "syss";
> ti,sysc-mask = <(SYSC_OMAP2_SOFTRESET |
> SYSC_OMAP2_AUTOIDLE)>;
> @@ -779,9 +780,9 @@
>
> aes2_target: target-module@4b700000 {
> compatible = "ti,sysc-omap2", "ti,sysc";
> - reg = <0x4b700080 0x4>,
> - <0x4b700084 0x4>,
> - <0x4b700088 0x4>;
> + reg = <0x4b700080 0x0 0x4>,
> + <0x4b700084 0x0 0x4>,
> + <0x4b700088 0x0 0x4>;
> reg-names = "rev", "sysc", "syss";
> ti,sysc-mask = <(SYSC_OMAP2_SOFTRESET |
> SYSC_OMAP2_AUTOIDLE)>;
> @@ -810,9 +811,9 @@
>
> sham_target: target-module@4b101000 {
> compatible = "ti,sysc-omap3-sham", "ti,sysc";
> - reg = <0x4b101100 0x4>,
> - <0x4b101110 0x4>,
> - <0x4b101114 0x4>;
> + reg = <0x4b101100 0x0 0x4>,
> + <0x4b101110 0x0 0x4>,
> + <0x4b101114 0x0 0x4>;
> reg-names = "rev", "sysc", "syss";
> ti,sysc-mask = <(SYSC_OMAP2_SOFTRESET |
> SYSC_OMAP2_AUTOIDLE)>;
> @@ -840,7 +841,7 @@
>
> opp_supply_mpu: opp-supply@4a003b20 {
> compatible = "ti,omap5-opp-supply";
> - reg = <0x4a003b20 0xc>;
> + reg = <0x4a003b20 0x0 0xc>;
> ti,efuse-settings = <
> /* uV offset */
> 1060000 0x0
> diff --git a/arch/arm/boot/dts/dra72x.dtsi b/arch/arm/boot/dts/dra72x.dtsi
> index 82b57a35abc0..09c1801c18c3 100644
> --- a/arch/arm/boot/dts/dra72x.dtsi
> +++ b/arch/arm/boot/dts/dra72x.dtsi
> @@ -60,9 +60,9 @@
> };
>
> &dss {
> - reg = <0x58000000 0x80>,
> - <0x58004054 0x4>,
> - <0x58004300 0x20>;
> + reg = <0x58000000 0x0 0x80>,
> + <0x58004054 0x0 0x4>,
> + <0x58004300 0x0 0x20>;
> reg-names = "dss", "pll1_clkctrl", "pll1";
>
> clocks = <&dss_clkctrl DRA7_DSS_DSS_CORE_CLKCTRL 8>,
> diff --git a/arch/arm/boot/dts/dra74x.dtsi b/arch/arm/boot/dts/dra74x.dtsi
> index c5abc436ca1f..a88a64af41e0 100644
> --- a/arch/arm/boot/dts/dra74x.dtsi
> +++ b/arch/arm/boot/dts/dra74x.dtsi
> @@ -39,22 +39,23 @@
> ocp {
> dsp2_system: dsp_system@41500000 {
> compatible = "syscon";
> - reg = <0x41500000 0x100>;
> + reg = <0x41500000 0x0 0x100>;
> };
>
> omap_dwc3_4: omap_dwc3_4@48940000 {
> compatible = "ti,dwc3";
> ti,hwmods = "usb_otg_ss4";
> - reg = <0x48940000 0x10000>;
> + reg = <0x48940000 0x0 0x10000>;
> interrupts = <GIC_SPI 346 IRQ_TYPE_LEVEL_HIGH>;
> #address-cells = <1>;
> #size-cells = <1>;
> utmi-mode = <2>;
> - ranges;
> + ranges = <0x0 0x48940000 0x20000>;
> status = "disabled";
> - usb4: usb@48950000 {
> +
> + usb4: usb@10000 {
> compatible = "snps,dwc3";
> - reg = <0x48950000 0x17000>;
> + reg = <0x10000 0x17000>;
> interrupts = <GIC_SPI 345 IRQ_TYPE_LEVEL_HIGH>,
> <GIC_SPI 345 IRQ_TYPE_LEVEL_HIGH>,
> <GIC_SPI 346 IRQ_TYPE_LEVEL_HIGH>;
> @@ -68,9 +69,9 @@
>
> target-module@41501000 {
> compatible = "ti,sysc-omap2", "ti,sysc";
> - reg = <0x41501000 0x4>,
> - <0x41501010 0x4>,
> - <0x41501014 0x4>;
> + reg = <0x41501000 0x0 0x4>,
> + <0x41501010 0x0 0x4>,
> + <0x41501014 0x0 0x4>;
> reg-names = "rev", "sysc", "syss";
> ti,sysc-sidle = <SYSC_IDLE_FORCE>,
> <SYSC_IDLE_NO>,
> @@ -97,9 +98,9 @@
>
> target-module@41502000 {
> compatible = "ti,sysc-omap2", "ti,sysc";
> - reg = <0x41502000 0x4>,
> - <0x41502010 0x4>,
> - <0x41502014 0x4>;
> + reg = <0x41502000 0x0 0x4>,
> + <0x41502010 0x0 0x4>,
> + <0x41502014 0x0 0x4>;
> reg-names = "rev", "sysc", "syss";
> ti,sysc-sidle = <SYSC_IDLE_FORCE>,
> <SYSC_IDLE_NO>,
> @@ -132,11 +133,11 @@
> };
>
> &dss {
> - reg = <0x58000000 0x80>,
> - <0x58004054 0x4>,
> - <0x58004300 0x20>,
> - <0x58009054 0x4>,
> - <0x58009300 0x20>;
> + reg = <0x58000000 0x0 0x80>,
> + <0x58004054 0x0 0x4>,
> + <0x58004300 0x0 0x20>,
> + <0x58009054 0x0 0x4>,
> + <0x58009300 0x0 0x20>;
> reg-names = "dss", "pll1_clkctrl", "pll1",
> "pll2_clkctrl", "pll2";
>
>

--
Texas Instruments Finland Oy, Porkkalankatu 22, 00180 Helsinki. Y-tunnus/Business ID: 0615521-4. Kotipaikka/Domicile: Helsinki

\
 
 \ /
  Last update: 2020-03-10 15:46    [W:0.102 / U:3.252 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site