lkml.org 
[lkml]   [2020]   [Feb]   [27]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH V2 4/4] arm64: dts: imx8mm: Add thermal zone support
Date
Add thermal zone and tmu node to support i.MX8MM thermal
driver, ONLY cpu thermal zone is supported, and cpu cooling
is also added.

Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
---
No change.
---
arch/arm64/boot/dts/freescale/imx8mm.dtsi | 43 +++++++++++++++++++++++++++++++
1 file changed, 43 insertions(+)

diff --git a/arch/arm64/boot/dts/freescale/imx8mm.dtsi b/arch/arm64/boot/dts/freescale/imx8mm.dtsi
index b3d0b29..e438095 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mm.dtsi
@@ -68,6 +68,7 @@
nvmem-cells = <&cpu_speed_grade>;
nvmem-cell-names = "speed_grade";
cpu-idle-states = <&cpu_pd_wait>;
+ #cooling-cells = <2>;
};

A53_1: cpu@1 {
@@ -80,6 +81,7 @@
next-level-cache = <&A53_L2>;
operating-points-v2 = <&a53_opp_table>;
cpu-idle-states = <&cpu_pd_wait>;
+ #cooling-cells = <2>;
};

A53_2: cpu@2 {
@@ -92,6 +94,7 @@
next-level-cache = <&A53_L2>;
operating-points-v2 = <&a53_opp_table>;
cpu-idle-states = <&cpu_pd_wait>;
+ #cooling-cells = <2>;
};

A53_3: cpu@3 {
@@ -104,6 +107,7 @@
next-level-cache = <&A53_L2>;
operating-points-v2 = <&a53_opp_table>;
cpu-idle-states = <&cpu_pd_wait>;
+ #cooling-cells = <2>;
};

A53_L2: l2-cache0 {
@@ -204,6 +208,38 @@
arm,no-tick-in-suspend;
};

+ thermal-zones {
+ cpu-thermal {
+ polling-delay-passive = <250>;
+ polling-delay = <2000>;
+ thermal-sensors = <&tmu>;
+ trips {
+ cpu_alert0: trip0 {
+ temperature = <85000>;
+ hysteresis = <2000>;
+ type = "passive";
+ };
+
+ cpu_crit0: trip1 {
+ temperature = <95000>;
+ hysteresis = <2000>;
+ type = "critical";
+ };
+ };
+
+ cooling-maps {
+ map0 {
+ trip = <&cpu_alert0>;
+ cooling-device =
+ <&A53_0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&A53_1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&A53_2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&A53_3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+ };
+ };
+ };
+ };
+
usbphynop1: usbphynop1 {
compatible = "usb-nop-xceiv";
clocks = <&clk IMX8MM_CLK_USB_PHY_REF>;
@@ -363,6 +399,13 @@
gpio-ranges = <&iomuxc 0 119 30>;
};

+ tmu: tmu@30260000 {
+ compatible = "fsl,imx8mm-tmu";
+ reg = <0x30260000 0x10000>;
+ clocks = <&clk IMX8MM_CLK_TMU_ROOT>;
+ #thermal-sensor-cells = <0>;
+ };
+
wdog1: watchdog@30280000 {
compatible = "fsl,imx8mm-wdt", "fsl,imx21-wdt";
reg = <0x30280000 0x10000>;
--
2.7.4
\
 
 \ /
  Last update: 2020-02-28 04:00    [W:0.087 / U:2.304 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site