lkml.org 
[lkml]   [2020]   [Feb]   [17]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: RPI4: fail too boot with an initrd
From
Date


On 17/02/2020 11:37, LABBE Corentin wrote:
> On Fri, Feb 14, 2020 at 06:15:27PM +0000, James Morse wrote:
>> Hi Corentin,
>>
>> On 14/02/2020 13:27, LABBE Corentin wrote:
>>> Since the inclusion of the "enable network support in RPi4 config" serie on uboot, I
>>> have started to work on adding the rpi4 in kernelCI.
>>> But I fail to succeed in using a kernel/dtb/ramdisk downloaded via tftp.
>>>
>>> Using booti I hit:
>>> [ 0.000000] Linux version 5.6.0-rc1-next-20200212 (clabbe@build2-bionic-1804) (gcc version 7.4.1 20181213 [linaro-7.4-2019.02 revision 56ec6f6b99cc167ff0c2f8e1a2eed33b1edc85d4] (Linaro GCC 7.4-2019.02)) #66 SMP PREEMPT Wed Feb 12 10:14:20 UTC 2020
>>> [ 0.000000] Machine model: Raspberry Pi 4 Model B
>>> [ 0.000000] earlycon: uart0 at MMIO32 0x00000000fe215040 (options '')
>>> [ 0.000000] printk: bootconsole [uart0] enabled
>>> [ 0.000000] efi: Getting EFI parameters from FDT:
>>> [ 0.000000] efi: UEFI not found.
>>
>> So no EFI,
>>
>>> [ 0.000000] OF: reserved mem: failed to allocate memory for node 'linux,cma'
>>
>> Out of memory.
>>
>>> [ 0.000000] cma: Failed to reserve 32 MiB
>>> [ 0.000000] Kernel panic - not syncing: Failed to allocate page table page
>>
>> Out of memory...
>>
>>> [ 0.000000] CPU: 0 PID: 0 Comm: swapper Not tainted 5.6.0-rc1-next-20200212 #66
>>> [ 0.000000] Hardware name: Raspberry Pi 4 Model B (DT)
>>> [ 0.000000] Call trace:
>>> [ 0.000000] dump_backtrace+0x0/0x1a0
>>> [ 0.000000] show_stack+0x14/0x20
>>> [ 0.000000] dump_stack+0xbc/0x104
>>> [ 0.000000] panic+0x16c/0x37c
>>> [ 0.000000] early_pgtable_alloc+0x30/0xa0
>>
>> ... really early!
>>
>>> [ 0.000000] __create_pgd_mapping+0x36c/0x588
>>> [ 0.000000] map_kernel_segment+0x70/0xa4
>>> [ 0.000000] paging_init+0xf4/0x528
>>> [ 0.000000] setup_arch+0x250/0x5d8
>>> [ 0.000000] start_kernel+0x90/0x6d8
>>>
>>>
>>> Since the same kernel boot with bootefi and that bootefi lack ramdisk address,
>>
>> Booting with EFI will cause linux to use the EFI memory map.
>>
>> Does your DT have a memory node? (or does it expect EFI to provide the information)
>>
>>
>>> I tried to add the address in the dtb via:
>>> fdt addr 0x02400000; fdt resize; fdt set /chosen linux,initrd-start 0x02700000; fdt set /chosen linux,initrd-end 0x10000000; bootefi 0x00080000 0x02400000
>>> But with that, I get:
>>> initrd not fully accessible via the linear mapping -- please check your bootloader ...
>>
>> So this one is an EFI boot, but you can't find where to put the initramfs such that the
>> kernel agrees its in memory.
>>
>> If you boot with 'efi=debug', linux will print the EFI memory map. Could you compare that
>> to where U-Boot thinks memory is?
>>
>> (it sounds like your DT memory node is missing, and your EFI memory map is surprisingly small)
>
> Hello
>
> Thanks for your advices.
>
> In the dtb of mainline linux:
> /* Will be filled by the bootloader */
> memory@0 {
> device_type = "memory";
> reg = <0 0 0>;
> };
>
> In uboot I have:
> static struct mm_region bcm2711_mem_map[] = {
> {
> .virt = 0x00000000UL,
> .phys = 0x00000000UL,
> .size = 0xfe000000UL,
> .attrs = PTE_BLOCK_MEMTYPE(MT_NORMAL) |
> PTE_BLOCK_INNER_SHARE
> }, {
> .virt = 0xfc000000UL,
> .phys = 0xfc000000UL,
> .size = 0x03800000UL,
> .attrs = PTE_BLOCK_MEMTYPE(MT_DEVICE_NGNRNE) |
> PTE_BLOCK_NON_SHARE |
> PTE_BLOCK_PXN | PTE_BLOCK_UXN
> }, {
> /* List terminator */
> 0,
> }
> };
> But I dont know if uboot use that for filling the memory node.

No it doesn't. U-Boot uses the DT from the firmware and passes this to the
kernel. But it seems you pass instead your own device-tree to the kernel, so you
will need to update the memory node to show the available memory on you board.

Regards,
Matthias

>
>
> Booting the rpi4 with efi=debug give:
> EFI stub: Booting Linux Kernel...
> EFI stub: EFI_RNG_PROTOCOL unavailable, no randomness supplied
> EFI stub: Using DTB from configuration table
> EFI stub: Exiting boot services and installing virtual address map...
> [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd083]
> [ 0.000000] Linux version 5.6.0-rc1-next-20200214 (clabbe@build2-bionic-1804) (gcc version 7.4.1 20181213 [linaro-7.4-2019.02 revision 56ec6f6b99cc167ff0c2f8e1a2eed33b1edc85d4] (Linaro GCC 7.4-2019.02)) #70 SMP PREEMPT Fri Feb 14 10:54:54 UTC 2020
> [ 0.000000] Machine model: Raspberry Pi 4 Model B
> [ 0.000000] earlycon: uart0 at MMIO32 0x00000000fe215040 (options '')
> [ 0.000000] printk: bootconsole [uart0] enabled
> [ 0.000000] efi: Getting EFI parameters from FDT:
> [ 0.000000] efi: System Table: 0x000000003b365590
> [ 0.000000] efi: MemMap Address: 0x0000000038484040
> [ 0.000000] efi: MemMap Size: 0x00000410
> [ 0.000000] efi: MemMap Desc. Size: 0x00000028
> [ 0.000000] efi: MemMap Desc. Version: 0x00000001
> [ 0.000000] efi: EFI v2.80 by Das U-Boot
> [ 0.000000] efi: SMBIOS=0x39f46000 MEMRESERVE=0x38487040
> [ 0.000000] efi: Processing EFI memory map:
> [ 0.000000] efi: 0x000000000000-0x000000000fff [Reserved | | | | | | | | | |WB| | | ]
> [ 0.000000] efi: 0x000000001000-0x00000007ffff [Conventional Memory| | | | | | | | | |WB| | | ]
> [ 0.000000] efi: 0x000000080000-0x000001b3ffff [Loader Data | | | | | | | | | |WB| | | ]
> [ 0.000000] efi: 0x000001b40000-0x000007efffff [Conventional Memory| | | | | | | | | |WB| | | ]
> [ 0.000000] efi: 0x000007f00000-0x000007f08fff [Boot Data | | | | | | | | | |WB| | | ]
> [ 0.000000] efi: 0x000007f09000-0x0000381fffff [Conventional Memory| | | | | | | | | |WB| | | ]
> [ 0.000000] efi: 0x000038200000-0x0000383fffff [Loader Data | | | | | | | | | |WB| | | ]
> [ 0.000000] efi: 0x000038400000-0x00003846ffff [Conventional Memory| | | | | | | | | |WB| | | ]
> [ 0.000000] efi: 0x000038470000-0x00003847ffff [Loader Data | | | | | | | | | |WB| | | ]
> [ 0.000000] efi: 0x000038480000-0x000038483fff [Conventional Memory| | | | | | | | | |WB| | | ]
> [ 0.000000] efi: 0x000038484000-0x000038487fff [Loader Data | | | | | | | | | |WB| | | ]
> [ 0.000000] efi: 0x000038488000-0x000039f40fff [Loader Code | | | | | | | | | |WB| | | ]
> [ 0.000000] efi: 0x000039f41000-0x000039f44fff [Reserved | | | | | | | | | |WB| | | ]
> [ 0.000000] efi: 0x000039f45000-0x000039f45fff [Boot Data | | | | | | | | | |WB| | | ]
> [ 0.000000] efi: 0x000039f46000-0x000039f46fff [Runtime Data |RUN| | | | | | | | |WB| | | ]
> [ 0.000000] efi: 0x000039f47000-0x000039f48fff [Boot Data | | | | | | | | | |WB| | | ]
> [ 0.000000] efi: 0x000039f49000-0x000039f4cfff [Reserved | | | | | | | | | |WB| | | ]
> [ 0.000000] efi: 0x000039f4d000-0x000039f4efff [Boot Data | | | | | | | | | |WB| | | ]
> [ 0.000000] efi: 0x000039f4f000-0x000039f52fff [Reserved | | | | | | | | | |WB| | | ]
> [ 0.000000] efi: 0x000039f53000-0x000039f53fff [Runtime Data |RUN| | | | | | | | |WB| | | ]
> [ 0.000000] efi: 0x000039f54000-0x000039f54fff [Reserved | | | | | | | | | |WB| | | ]
> [ 0.000000] efi: 0x000039f55000-0x00003b35ffff [Loader Data | | | | | | | | | |WB| | | ]
> [ 0.000000] efi: 0x00003b360000-0x00003b36ffff [Runtime Code |RUN| | | | | | | | |WB| | | ]
> [ 0.000000] efi: 0x00003b370000-0x00003b3fffff [Loader Data | | | | | | | | | |WB| | | ]
> [ 0.000000] efi: 0x000040000000-0x0000fbffffff [Boot Data | | | | | | | | | |WB| | | ]
> [ 0.000000] efi: 0x0000fe100000-0x0000fe100fff [Memory Mapped I/O |RUN| | | | | | | | | | | | ]
> [ 0.000000] ------------[ cut here ]------------
> [ 0.000000] initrd not fully accessible via the linear mapping -- please check your bootloader ...
>
> Regards
>
> _______________________________________________
> linux-arm-kernel mailing list
> linux-arm-kernel@lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
>

\
 
 \ /
  Last update: 2020-02-17 11:51    [W:0.054 / U:2.836 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site