lkml.org 
[lkml]   [2020]   [Feb]   [12]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Subject[PATCH v6 0/5] add Tegra194 XUSB host and pad controller support
Date
v6:
phy: tegra: xusb: Protect Tegra186 soc with config
- no change

phy: tegra: xusb: Add Tegra194 support
- no change

dt-bindings: phy: tegra: Add Tegra194 support
- no change

arm64: tegra: Add XUSB and pad controller on Tegra194
- rebased

arm64: tegra: Enable XUSB host in P2972-0000 board
- re-use "maximum-speed" instead of adding "nvidia,disable-gen2"

v5:
phy: tegra: xusb: Protect Tegra186 soc with config
- no change

phy: tegra: xusb: Add Tegra194 support
- re-use "maximum-speed" instead of adding "nvidia,disable-gen2"

dt-bindings: phy: tegra: Add Tegra194 support
- re-use "maximum-speed" instead of adding "nvidia,disable-gen2"

arm64: tegra: Add XUSB and pad controller on Tegra194
- no change

arm64: tegra: Enable XUSB host in P2972-0000 board
- no change

v3:
add change log to cover latter

v2:
xhci: tegra: Parameterize mailbox register addresses
- no change

usb: host: xhci-tegra: Add Tegra194 XHCI support
- no change

phy: tegra: xusb: Protect Tegra186 soc with config
- new patch to protect Tegra186 soc data with config

phy: tegra: xusb: Add Tegra194 support
- removed unnecessary #if/#endif pairs
- introduce new soc->supports_gen2 flag which indicate whether or not
a soc supports USB 3.1 Gen 2 speed

dt-bindings: phy: tegra: Add Tegra194 support
- fix a typo

arm64: tegra: Add XUSB and pad controller on Tegra194
- renamed xhci@3610000 with usb@3610000
- moved padctl@3520000 and usb@3610000 inside /cbb
- cleaned up "clocks" property of usb@3610000 node
- added blanks lines to visually separate blocks

arm64: tegra: Enable XUSB host in P2972-0000 board
- use capitalization of regulator names
- fix gpio property of VDD_5V_SATA regulator


JC Kuo (5):
phy: tegra: xusb: Protect Tegra186 soc with config
phy: tegra: xusb: Add Tegra194 support
dt-bindings: phy: tegra: Add Tegra194 support
arm64: tegra: Add XUSB and pad controller on Tegra194
arm64: tegra: Enable XUSB host in P2972-0000 board

.../phy/nvidia,tegra124-xusb-padctl.txt | 18 +++
.../arm64/boot/dts/nvidia/tegra194-p2888.dtsi | 36 ++++-
.../boot/dts/nvidia/tegra194-p2972-0000.dts | 63 ++++++++
arch/arm64/boot/dts/nvidia/tegra194.dtsi | 139 +++++++++++++++++
drivers/phy/tegra/Makefile | 1 +
drivers/phy/tegra/xusb-tegra186.c | 143 +++++++++++++-----
drivers/phy/tegra/xusb.c | 17 +++
drivers/phy/tegra/xusb.h | 5 +
8 files changed, 387 insertions(+), 35 deletions(-)

--
2.17.1

\
 
 \ /
  Last update: 2020-02-12 07:13    [W:0.093 / U:1.512 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site