lkml.org 
[lkml]   [2020]   [Nov]   [4]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
Date
From
SubjectRe: [PATCH v2 3/6] ARM: dts: sun8i: s3: Add dtsi for the Elimo Impetus SoM
Hi

On Tue, Nov 03, 2020 at 04:28:27PM +0000, Matteo Scordino wrote:
> --
> Matteo Scordino / Embedded Software Consultant
> Mobile: +44 (0)7463701446
>
> On Mon, 2020-11-02 at 11:05 +0100, Maxime Ripard wrote:
> > Hi!
> >
> > On Fri, Oct 30, 2020 at 11:43:22PM +0000, Matteo Scordino wrote:
> > > The Elimo Engineering Impetus is an Open Source Hardware System-on-Module
> > > based on the SoChip S3 SoC.
> > >
> > > It is meant for integration into carrier boards or, more generally,
> > > larger designs, and uses an M2 connector to facilitate that.
> > >
> > > Interfaces on the M.2/NGFF 42mm connector:
> > > WiFi IEEE 802. 11abgn (on-module Realtek)
> > > Bluetooth 4.2/BLE (on-module Realtek)
> > > RGB LCD Interface (on-module connector)
> > > MIPI Camera Interface (on-module connector)
> > > IEEE 802. 3u Ethernet MAC (external connecto)
> > > USB2.0 (Host, Device, OTG) (external connector)
> > > Audio Line In/Out (external connector)
> > >
> > > Signed-off-by: Matteo Scordino <matteo.scordino@gmail.com>
> > > ---
> > > arch/arm/boot/dts/sun8i-s3-elimo-impetus.dtsi | 51 +++++++++++++++++++
> > > 1 file changed, 51 insertions(+)
> > > create mode 100644 arch/arm/boot/dts/sun8i-s3-elimo-impetus.dtsi
> > >
> > > diff --git a/arch/arm/boot/dts/sun8i-s3-elimo-impetus.dtsi b/arch/arm/boot/dts/sun8i-s3-elimo-impetus.dtsi
> > > new file mode 100644
> > > index 000000000000..f219188fc9ba
> > > --- /dev/null
> > > +++ b/arch/arm/boot/dts/sun8i-s3-elimo-impetus.dtsi
> > > @@ -0,0 +1,51 @@
> > > +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> > > +/*
> > > + * Copyright (C) 2020 Matteo Scordino <matteo@elimo.io>
> > > + */
> > > +
> > > +/dts-v1/;
> > > +#include "sun8i-v3.dtsi"
> > > +#include "sunxi-common-regulators.dtsi"
> > > +
> > > +/ {
> > > + model = "Elimo Impetus SoM";
> > > + compatible = "elimo,impetus", "sochip,s3", "allwinner,sun8i-v3";
> > > +
> > > + aliases {
> > > + serial0 = &uart0;
> > > + serial1 = &uart1;
> > > + };
> > > +
> > > + chosen {
> > > + stdout-path = "serial0:115200n8";
> > > + };
> > > +};
> > > +
> > > +&mmc0 {
> > > + broken-cd;
> > > + bus-width = <4>;
> > > + vmmc-supply = <&reg_vcc3v3>;
> > > + status = "okay";
> > > +};
> > > +
> > > +&uart0 {
> > > + pinctrl-0 = <&uart0_pb_pins>;
> > > + pinctrl-names = "default";
> > > + status = "okay";
> > > +};
> > > +
> > > +&uart1 {
> > > + pinctrl-0 = <&uart1_pg_pins>;
> > > + pinctrl-names = "default";
> > > + status = "okay";
> > > +};
> > What is uart1 used for? the BT chip?
> >
> > Maxime
>
> No, BT is provided over SDIO by a Cypress 43455.
> When used with the Initium carrier board, UART1 goes to an FTDI bridge that is
> connected to the same USB-C connector that is used for power.
> The idea being, if want an application that uses the UART to communicate with a
> PC, it's convenient to provide power+connectivity on a single port.
>
> I guess your point is that we would be better off only defining this in the DTS
> of the carrier board?

I wasn't trying to make any point, it was a legitimate question, we
don't want to enable something that is optional or could be used for
something else (like a UART exposed on a generic pin header).

But from what you're telling me, yeah, it should be moved to the
daughter board DTS.

Maxime

[unhandled content-type:application/pgp-signature]
\
 
 \ /
  Last update: 2020-11-04 20:04    [W:0.051 / U:2.488 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site