lkml.org 
[lkml]   [2020]   [Nov]   [3]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH v7 1/6] dt-bindings: devfreq: Add documentation for the interconnect properties
From
Date
Hi Sylwester,

This patch contains one typo.

On 10/30/20 9:51 PM, Sylwester Nawrocki wrote:
> Add documentation for new optional properties in the exynos bus nodes:
> interconnects, #interconnect-cells, samsung,data-clock-ratio.
> These properties allow to specify the SoC interconnect structure which
> then allows the interconnect consumer devices to request specific
> bandwidth requirements.
>
> Signed-off-by: Artur Świgoń <a.swigon@samsung.com>
> Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
> ---
> Changes for v7:
> - bus-width property replaced with samsung,data-clock-ratio,
> - the interconnect consumer bindings used instead of vendor specific
> properties
>
> Changes for v6:
> - added dts example of bus hierarchy definition and the interconnect
> consumer,
> - added new bus-width property.
>
> Changes for v5:
> - exynos,interconnect-parent-node renamed to samsung,interconnect-parent
> ---
> .../devicetree/bindings/devfreq/exynos-bus.txt | 68 +++++++++++++++++++++-
> 1 file changed, 66 insertions(+), 2 deletions(-)
>
> diff --git a/Documentation/devicetree/bindings/devfreq/exynos-bus.txt b/Documentation/devicetree/bindings/devfreq/exynos-bus.txt
> index e71f752..e34175c 100644
> --- a/Documentation/devicetree/bindings/devfreq/exynos-bus.txt
> +++ b/Documentation/devicetree/bindings/devfreq/exynos-bus.txt
> @@ -51,6 +51,16 @@ Optional properties only for parent bus device:
> - exynos,saturation-ratio: the percentage value which is used to calibrate
> the performance count against total cycle count.
>
> +Optional properties for interconnect functionality (QoS frequency constraints):
> +- #interconnect-cells: should be 0.
> +- interconnects: as documented in ../interconnect.txt, describes a path
> + at the higher level interconnects used by this interconnect provider.
> + If this interconnect provider is a parent of a top level interconnect
> + provider the property contains only one phandle.
> +
> +- samsung,data-clock-ratio: ratio of the data troughput in B/s to minimum data

s/troughput/throughput

> + clock frequency in Hz, default value is 8 when this property is missing.
> +
> Detailed correlation between sub-blocks and power line according to Exynos SoC:
> - In case of Exynos3250, there are two power line as following:
> VDD_MIF |--- DMC
> @@ -135,7 +145,7 @@ Detailed correlation between sub-blocks and power line according to Exynos SoC:
> |--- PERIC (Fixed clock rate)
> |--- FSYS (Fixed clock rate)
>
> -Example1:
> +Example 1:
> Show the AXI buses of Exynos3250 SoC. Exynos3250 divides the buses to
> power line (regulator). The MIF (Memory Interface) AXI bus is used to
> transfer data between DRAM and CPU and uses the VDD_MIF regulator.
> @@ -184,7 +194,7 @@ Example1:
> |L5 |200000 |200000 |400000 |300000 | ||1000000 |
> ----------------------------------------------------------
>
> -Example2 :
> +Example 2:
> The bus of DMC (Dynamic Memory Controller) block in exynos3250.dtsi
> is listed below:
>
> @@ -419,3 +429,57 @@ Example2 :
> devfreq = <&bus_leftbus>;
> status = "okay";
> };
> +
> +Example 3:
> + An interconnect path "bus_display -- bus_leftbus -- bus_dmc" on
> + Exynos4412 SoC with video mixer as an interconnect consumer device.
> +
> + soc {
> + bus_dmc: bus_dmc {
> + compatible = "samsung,exynos-bus";
> + clocks = <&clock CLK_DIV_DMC>;
> + clock-names = "bus";
> + operating-points-v2 = <&bus_dmc_opp_table>;
> + samsung,data-clock-ratio = <4>;
> + #interconnect-cells = <0>;
> + };
> +
> + bus_leftbus: bus_leftbus {
> + compatible = "samsung,exynos-bus";
> + clocks = <&clock CLK_DIV_GDL>;
> + clock-names = "bus";
> + operating-points-v2 = <&bus_leftbus_opp_table>;
> + #interconnect-cells = <0>;
> + interconnects = <&bus_dmc>;
> + };
> +
> + bus_display: bus_display {
> + compatible = "samsung,exynos-bus";
> + clocks = <&clock CLK_ACLK160>;
> + clock-names = "bus";
> + operating-points-v2 = <&bus_display_opp_table>;
> + #interconnect-cells = <0>;
> + interconnects = <&bus_leftbus &bus_dmc>;

About adding two icc_node, I queried you on patch2.

> + };
> +
> + bus_dmc_opp_table: opp_table1 {
> + compatible = "operating-points-v2";
> + /* ... */
> + }
> +
> + bus_leftbus_opp_table: opp_table3 {
> + compatible = "operating-points-v2";
> + /* ... */
> + };
> +
> + bus_display_opp_table: opp_table4 {
> + compatible = "operating-points-v2";
> + /* .. */
> + };
> +
> + &mixer {
> + compatible = "samsung,exynos4212-mixer";
> + interconnects = <&bus_display &bus_dmc>;
> + /* ... */
> + };
> + };
>


--
Best Regards,
Chanwoo Choi
Samsung Electronics

\
 
 \ /
  Last update: 2020-11-03 10:27    [W:0.141 / U:0.704 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site