lkml.org 
[lkml]   [2020]   [Nov]   [15]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH RFC v2 3/5] net: stmmac: dwmac-meson8b: use picoseconds for the RGMII RX delay
Date
Amlogic Meson G12A, G12B and SM1 SoCs have a more advanced RGMII RX
delay register which allows picoseconds precision. Parse the new
"amlogic,rgmii-rx-delay-ps" property or fall back to the old
"amlogic,rx-delay-ns".

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
---
.../ethernet/stmicro/stmmac/dwmac-meson8b.c | 22 ++++++++++++-------
1 file changed, 14 insertions(+), 8 deletions(-)

diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac-meson8b.c b/drivers/net/ethernet/stmicro/stmmac/dwmac-meson8b.c
index e27e2e7a53fd..03fce678b9f5 100644
--- a/drivers/net/ethernet/stmicro/stmmac/dwmac-meson8b.c
+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-meson8b.c
@@ -83,7 +83,7 @@ struct meson8b_dwmac {
phy_interface_t phy_mode;
struct clk *rgmii_tx_clk;
u32 tx_delay_ns;
- u32 rx_delay_ns;
+ u32 rx_delay_ps;
struct clk *timing_adj_clk;
};

@@ -276,7 +276,7 @@ static int meson8b_init_prg_eth(struct meson8b_dwmac *dwmac)
tx_dly_config = FIELD_PREP(PRG_ETH0_TXDLY_MASK,
dwmac->tx_delay_ns >> 1);

- if (dwmac->rx_delay_ns == 2)
+ if (dwmac->rx_delay_ps == 2000)
rx_dly_config = PRG_ETH0_ADJ_ENABLE | PRG_ETH0_ADJ_SETUP;
else
rx_dly_config = 0;
@@ -406,14 +406,20 @@ static int meson8b_dwmac_probe(struct platform_device *pdev)
&dwmac->tx_delay_ns))
dwmac->tx_delay_ns = 2;

- /* use 0ns as fallback since this is what most boards actually use */
- if (of_property_read_u32(pdev->dev.of_node, "amlogic,rx-delay-ns",
- &dwmac->rx_delay_ns))
- dwmac->rx_delay_ns = 0;
+ /* RX delay defaults to 0ps since this is what many boards use */
+ if (of_property_read_u32(pdev->dev.of_node,
+ "amlogic,rgmii-rx-delay-ps",
+ &dwmac->rx_delay_ps)) {
+ if (!of_property_read_u32(pdev->dev.of_node,
+ "amlogic,rx-delay-ns",
+ &dwmac->rx_delay_ps))
+ /* convert ns to ps */
+ dwmac->rx_delay_ps *= 1000;
+ }

- if (dwmac->rx_delay_ns != 0 && dwmac->rx_delay_ns != 2) {
+ if (dwmac->rx_delay_ps != 0 && dwmac->rx_delay_ps != 2000) {
dev_err(&pdev->dev,
- "The only allowed RX delays values are: 0ns, 2ns");
+ "The only allowed RX delays values are: 0ps, 2000ps");
ret = -EINVAL;
goto err_remove_config_dt;
}
--
2.29.2
\
 
 \ /
  Last update: 2020-11-15 19:56    [W:0.130 / U:21.244 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site