lkml.org 
[lkml]   [2020]   [Oct]   [14]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
SubjectRe: [PATCH 1/1] net: ftgmac100: add handling of mdio/phy nodes for ast2400/2500
From
Date
On Wed, 2020-10-14 at 05:23 +0000, Joel Stanley wrote:
> Hi Ivan,
>
> On Tue, 13 Oct 2020 at 12:38, Ivan Mikhaylov <i.mikhaylov@yadro.com> wrote:
> > phy-handle can't be handled well for ast2400/2500 which has an embedded
> > MDIO controller. Add ftgmac100_mdio_setup for ast2400/2500 and initialize
> > PHYs from mdio child node with of_mdiobus_register.
>
> Good idea. The driver has become a mess of different ways to connect
> the phy and it needs to be cleaned up. I have a patch that fixes
> rmmod, which is currently broken.
>
>
>
> > Signed-off-by: Ivan Mikhaylov <i.mikhaylov@yadro.com>
> > ---
> > drivers/net/ethernet/faraday/ftgmac100.c | 114 ++++++++++++++---------
> > 1 file changed, 69 insertions(+), 45 deletions(-)
> >
> > diff --git a/drivers/net/ethernet/faraday/ftgmac100.c
> > b/drivers/net/ethernet/faraday/ftgmac100.c
> > index 87236206366f..e32066519ec1 100644
> > --- a/drivers/net/ethernet/faraday/ftgmac100.c
> > +++ b/drivers/net/ethernet/faraday/ftgmac100.c
> > @@ -1044,11 +1044,47 @@ static void ftgmac100_adjust_link(struct net_device
> > *netdev)
> > schedule_work(&priv->reset_task);
> > }
> >
> > -static int ftgmac100_mii_probe(struct ftgmac100 *priv, phy_interface_t
> > intf)
> > +static int ftgmac100_mii_probe(struct net_device *netdev)
> > {
> > - struct net_device *netdev = priv->netdev;
> > + struct ftgmac100 *priv = netdev_priv(netdev);
> > + struct platform_device *pdev = to_platform_device(priv->dev);
> > + struct device_node *np = pdev->dev.of_node;
> > + phy_interface_t phy_intf = PHY_INTERFACE_MODE_RGMII;
> > struct phy_device *phydev;
> >
> > + /* Get PHY mode from device-tree */
> > + if (np) {
> > + /* Default to RGMII. It's a gigabit part after all */
> > + phy_intf = of_get_phy_mode(np, &phy_intf);
> > + if (phy_intf < 0)
> > + phy_intf = PHY_INTERFACE_MODE_RGMII;
> > +
> > + /* Aspeed only supports these. I don't know about other IP
> > + * block vendors so I'm going to just let them through for
> > + * now. Note that this is only a warning if for some obscure
> > + * reason the DT really means to lie about it or it's a
> > newer
> > + * part we don't know about.
> > + *
> > + * On the Aspeed SoC there are additionally straps and SCU
> > + * control bits that could tell us what the interface is
> > + * (or allow us to configure it while the IP block is held
> > + * in reset). For now I chose to keep this driver away from
> > + * those SoC specific bits and assume the device-tree is
> > + * right and the SCU has been configured properly by pinmux
> > + * or the firmware.
> > + */
> > + if (priv->is_aspeed &&
> > + phy_intf != PHY_INTERFACE_MODE_RMII &&
> > + phy_intf != PHY_INTERFACE_MODE_RGMII &&
> > + phy_intf != PHY_INTERFACE_MODE_RGMII_ID &&
> > + phy_intf != PHY_INTERFACE_MODE_RGMII_RXID &&
> > + phy_intf != PHY_INTERFACE_MODE_RGMII_TXID) {
> > + netdev_warn(netdev,
> > + "Unsupported PHY mode %s !\n",
> > + phy_modes(phy_intf));
> > + }
>
> Why do we move this?

I've tried to detach PHY connect from ftgmac100_setup_mdio register function.
Tried to decouple MDIO and PHY levels.

>
> > + }
> > +
> > phydev = phy_find_first(priv->mii_bus);
> > if (!phydev) {
> > netdev_info(netdev, "%s: no PHY found\n", netdev->name);
> > @@ -1056,7 +1092,7 @@ static int ftgmac100_mii_probe(struct ftgmac100 *priv,
> > phy_interface_t intf)
> > }
> >
> > phydev = phy_connect(netdev, phydev_name(phydev),
> > - &ftgmac100_adjust_link, intf);
> > + &ftgmac100_adjust_link, phy_intf);
> >
> > if (IS_ERR(phydev)) {
> > netdev_err(netdev, "%s: Could not attach to PHY\n", netdev-
> > >name);
> > @@ -1601,8 +1637,8 @@ static int ftgmac100_setup_mdio(struct net_device
> > *netdev)
> > {
> > struct ftgmac100 *priv = netdev_priv(netdev);
> > struct platform_device *pdev = to_platform_device(priv->dev);
> > - phy_interface_t phy_intf = PHY_INTERFACE_MODE_RGMII;
> > struct device_node *np = pdev->dev.of_node;
> > + struct device_node *mdio_np;
> > int i, err = 0;
> > u32 reg;
> >
> > @@ -1623,39 +1659,6 @@ static int ftgmac100_setup_mdio(struct net_device
> > *netdev)
> > iowrite32(reg, priv->base + FTGMAC100_OFFSET_REVR);
> > }
> >
> > - /* Get PHY mode from device-tree */
> > - if (np) {
> > - /* Default to RGMII. It's a gigabit part after all */
> > - err = of_get_phy_mode(np, &phy_intf);
> > - if (err)
> > - phy_intf = PHY_INTERFACE_MODE_RGMII;
> > -
> > - /* Aspeed only supports these. I don't know about other IP
> > - * block vendors so I'm going to just let them through for
> > - * now. Note that this is only a warning if for some obscure
> > - * reason the DT really means to lie about it or it's a
> > newer
> > - * part we don't know about.
> > - *
> > - * On the Aspeed SoC there are additionally straps and SCU
> > - * control bits that could tell us what the interface is
> > - * (or allow us to configure it while the IP block is held
> > - * in reset). For now I chose to keep this driver away from
> > - * those SoC specific bits and assume the device-tree is
> > - * right and the SCU has been configured properly by pinmux
> > - * or the firmware.
> > - */
> > - if (priv->is_aspeed &&
> > - phy_intf != PHY_INTERFACE_MODE_RMII &&
> > - phy_intf != PHY_INTERFACE_MODE_RGMII &&
> > - phy_intf != PHY_INTERFACE_MODE_RGMII_ID &&
> > - phy_intf != PHY_INTERFACE_MODE_RGMII_RXID &&
> > - phy_intf != PHY_INTERFACE_MODE_RGMII_TXID) {
> > - netdev_warn(netdev,
> > - "Unsupported PHY mode %s !\n",
> > - phy_modes(phy_intf));
> > - }
> > - }
> > -
> > priv->mii_bus->name = "ftgmac100_mdio";
> > snprintf(priv->mii_bus->id, MII_BUS_ID_SIZE, "%s-%d",
> > pdev->name, pdev->id);
> > @@ -1667,22 +1670,22 @@ static int ftgmac100_setup_mdio(struct net_device
> > *netdev)
> > for (i = 0; i < PHY_MAX_ADDR; i++)
> > priv->mii_bus->irq[i] = PHY_POLL;
> >
> > - err = mdiobus_register(priv->mii_bus);
> > + mdio_np = of_get_child_by_name(np, "mdio");
> > + if (mdio_np)
> > + err = of_mdiobus_register(priv->mii_bus, mdio_np);
> > + else
> > + err = mdiobus_register(priv->mii_bus);
> > +
> > if (err) {
> > dev_err(priv->dev, "Cannot register MDIO bus!\n");
> > goto err_register_mdiobus;
> > }
> >
> > - err = ftgmac100_mii_probe(priv, phy_intf);
> > - if (err) {
> > - dev_err(priv->dev, "MII Probe failed!\n");
> > - goto err_mii_probe;
> > - }
> > + if (mdio_np)
> > + of_node_put(mdio_np);
>
> By the time I get down here I'm lost. Do you think you could split the
> change up into a few smaller patches?
>
> If not, try to explain what the various hunks of your change are trying to do.
>

Yes, you're right, I see two patches for now from your comments:
1. phy connect detach from ftgmac100_setup_mdio
2. add ast2400/2500 phy-handle support

Thanks.

\
 
 \ /
  Last update: 2020-10-14 15:20    [W:0.066 / U:0.564 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site