lkml.org 
[lkml]   [2020]   [Oct]   [13]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH 10/18] dt-bindings: usb: Convert DWC USB3 bindings to DT schema
On Sun, Oct 11, 2020 at 01:41:13AM +0300, Serge Semin wrote:
> DWC USB3 DT node is supposed to be compliant with the Generic xHCI
> Controller schema, but with additional vendor-specific properties, the
> controller-specific reference clocks and PHYs. So let's convert the
> currently available legacy text-based DWC USB3 bindings to the DT schema
> and make sure the DWC USB3 nodes are also validated against the
> usb-xhci.yaml schema.
>
> Note we have to discard the nodename restriction of being prefixed with
> "dwc3@" string, since in accordance with the usb-hcd.yaml schema USB nodes
> are supposed to be named as "^usb(@.*)".
>
> Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
>
> ---
>
> Alas applying the usb-hcd.yaml schema on the DWC USB3 nodes will cause
> dtbs_check failures since a lot of "snps,dwc3"-compatible DT nodes are
> named with prefixes like "^dwc3@", "^usb[0-9]@" and even "^dwusb@", while
> usb-hcd.yaml permits the "^usb@" prefix only. As I see it the better but
> more painful solution would be to fix the corresponding DTS files (it's
> some of the Qualcomm, HiSilicon, Exynos, Allwinner, Omap, Stih, APM and
> Freescale DTS'es) so the DWC USB3 DT nodes would comply with the generic
> USB HCD node naming schema. Alternatively we could either extend the
> naming space in the usb-hcd.yaml or extract the generic properties to a
> dedicated DT schema file. What do you think?

IMO, we should fix the node names.

> ---
> .../devicetree/bindings/usb/dwc3.txt | 125 --------
> .../devicetree/bindings/usb/snps,dwc3.yaml | 295 ++++++++++++++++++
> 2 files changed, 295 insertions(+), 125 deletions(-)
> delete mode 100644 Documentation/devicetree/bindings/usb/dwc3.txt
> create mode 100644 Documentation/devicetree/bindings/usb/snps,dwc3.yaml
>
> diff --git a/Documentation/devicetree/bindings/usb/dwc3.txt b/Documentation/devicetree/bindings/usb/dwc3.txt
> deleted file mode 100644
> index d03edf9d3935..000000000000
> --- a/Documentation/devicetree/bindings/usb/dwc3.txt
> +++ /dev/null
> @@ -1,125 +0,0 @@
> -synopsys DWC3 CORE
> -
> -DWC3- USB3 CONTROLLER. Complies to the generic USB binding properties
> - as described in 'usb/generic.txt'
> -
> -Required properties:
> - - compatible: must be "snps,dwc3"
> - - reg : Address and length of the register set for the device
> - - interrupts: Interrupts used by the dwc3 controller.
> - - clock-names: list of clock names. Ideally should be "ref",
> - "bus_early", "suspend" but may be less or more.
> - - clocks: list of phandle and clock specifier pairs corresponding to
> - entries in the clock-names property.
> -
> -Exception for clocks:
> - clocks are optional if the parent node (i.e. glue-layer) is compatible to
> - one of the following:
> - "cavium,octeon-7130-usb-uctl"
> - "qcom,dwc3"
> - "samsung,exynos5250-dwusb3"
> - "samsung,exynos5433-dwusb3"
> - "samsung,exynos7-dwusb3"
> - "sprd,sc9860-dwc3"
> - "st,stih407-dwc3"
> - "ti,am437x-dwc3"
> - "ti,dwc3"
> - "ti,keystone-dwc3"
> - "rockchip,rk3399-dwc3"
> - "xlnx,zynqmp-dwc3"
> -
> -Optional properties:
> - - usb-phy : array of phandle for the PHY device. The first element
> - in the array is expected to be a handle to the USB2/HS PHY and
> - the second element is expected to be a handle to the USB3/SS PHY
> - - phys: from the *Generic PHY* bindings
> - - phy-names: from the *Generic PHY* bindings; supported names are "usb2-phy"
> - or "usb3-phy".
> - - resets: set of phandle and reset specifier pairs
> - - snps,usb2-lpm-disable: indicate if we don't want to enable USB2 HW LPM
> - - snps,usb3_lpm_capable: determines if platform is USB3 LPM capable
> - - snps,dis-start-transfer-quirk: when set, disable isoc START TRANSFER command
> - failure SW work-around for DWC_usb31 version 1.70a-ea06
> - and prior.
> - - snps,disable_scramble_quirk: true when SW should disable data scrambling.
> - Only really useful for FPGA builds.
> - - snps,has-lpm-erratum: true when DWC3 was configured with LPM Erratum enabled
> - - snps,lpm-nyet-threshold: LPM NYET threshold
> - - snps,u2exit_lfps_quirk: set if we want to enable u2exit lfps quirk
> - - snps,u2ss_inp3_quirk: set if we enable P3 OK for U2/SS Inactive quirk
> - - snps,req_p1p2p3_quirk: when set, the core will always request for
> - P1/P2/P3 transition sequence.
> - - snps,del_p1p2p3_quirk: when set core will delay P1/P2/P3 until a certain
> - amount of 8B10B errors occur.
> - - snps,del_phy_power_chg_quirk: when set core will delay PHY power change
> - from P0 to P1/P2/P3.
> - - snps,lfps_filter_quirk: when set core will filter LFPS reception.
> - - snps,rx_detect_poll_quirk: when set core will disable a 400us delay to start
> - Polling LFPS after RX.Detect.
> - - snps,tx_de_emphasis_quirk: when set core will set Tx de-emphasis value.
> - - snps,tx_de_emphasis: the value driven to the PHY is controlled by the
> - LTSSM during USB3 Compliance mode.
> - - snps,dis_u3_susphy_quirk: when set core will disable USB3 suspend phy.
> - - snps,dis_u2_susphy_quirk: when set core will disable USB2 suspend phy.
> - - snps,dis_enblslpm_quirk: when set clears the enblslpm in GUSB2PHYCFG,
> - disabling the suspend signal to the PHY.
> - - snps,dis-u1-entry-quirk: set if link entering into U1 needs to be disabled.
> - - snps,dis-u2-entry-quirk: set if link entering into U2 needs to be disabled.
> - - snps,dis_rxdet_inp3_quirk: when set core will disable receiver detection
> - in PHY P3 power state.
> - - snps,dis-u2-freeclk-exists-quirk: when set, clear the u2_freeclk_exists
> - in GUSB2PHYCFG, specify that USB2 PHY doesn't provide
> - a free-running PHY clock.
> - - snps,dis-del-phy-power-chg-quirk: when set core will change PHY power
> - from P0 to P1/P2/P3 without delay.
> - - snps,dis-tx-ipgap-linecheck-quirk: when set, disable u2mac linestate check
> - during HS transmit.
> - - snps,parkmode-disable-ss-quirk: when set, all SuperSpeed bus instances in
> - park mode are disabled.
> - - snps,dis_metastability_quirk: when set, disable metastability workaround.
> - CAUTION: use only if you are absolutely sure of it.
> - - snps,is-utmi-l1-suspend: true when DWC3 asserts output signal
> - utmi_l1_suspend_n, false when asserts utmi_sleep_n
> - - snps,hird-threshold: HIRD threshold
> - - snps,hsphy_interface: High-Speed PHY interface selection between "utmi" for
> - UTMI+ and "ulpi" for ULPI when the DWC_USB3_HSPHY_INTERFACE has value 3.
> - - snps,quirk-frame-length-adjustment: Value for GFLADJ_30MHZ field of GFLADJ
> - register for post-silicon frame length adjustment when the
> - fladj_30mhz_sdbnd signal is invalid or incorrect.
> - - snps,rx-thr-num-pkt-prd: periodic ESS RX packet threshold count - host mode
> - only. Set this and rx-max-burst-prd to a valid,
> - non-zero value 1-16 (DWC_usb31 programming guide
> - section 1.2.4) to enable periodic ESS RX threshold.
> - - snps,rx-max-burst-prd: max periodic ESS RX burst size - host mode only. Set
> - this and rx-thr-num-pkt-prd to a valid, non-zero value
> - 1-16 (DWC_usb31 programming guide section 1.2.4) to
> - enable periodic ESS RX threshold.
> - - snps,tx-thr-num-pkt-prd: periodic ESS TX packet threshold count - host mode
> - only. Set this and tx-max-burst-prd to a valid,
> - non-zero value 1-16 (DWC_usb31 programming guide
> - section 1.2.3) to enable periodic ESS TX threshold.
> - - snps,tx-max-burst-prd: max periodic ESS TX burst size - host mode only. Set
> - this and tx-thr-num-pkt-prd to a valid, non-zero value
> - 1-16 (DWC_usb31 programming guide section 1.2.3) to
> - enable periodic ESS TX threshold.
> -
> - - <DEPRECATED> tx-fifo-resize: determines if the FIFO *has* to be reallocated.
> - - snps,incr-burst-type-adjustment: Value for INCR burst type of GSBUSCFG0
> - register, undefined length INCR burst type enable and INCRx type.
> - When just one value, which means INCRX burst mode enabled. When
> - more than one value, which means undefined length INCR burst type
> - enabled. The values can be 1, 4, 8, 16, 32, 64, 128 and 256.
> -
> - - in addition all properties from usb-xhci.txt from the current directory are
> - supported as well
> -
> -
> -This is usually a subnode to DWC3 glue to which it is connected.
> -
> -dwc3@4a030000 {
> - compatible = "snps,dwc3";
> - reg = <0x4a030000 0xcfff>;
> - interrupts = <0 92 4>
> - usb-phy = <&usb2_phy>, <&usb3,phy>;
> - snps,incr-burst-type-adjustment = <1>, <4>, <8>, <16>;
> -};
> diff --git a/Documentation/devicetree/bindings/usb/snps,dwc3.yaml b/Documentation/devicetree/bindings/usb/snps,dwc3.yaml
> new file mode 100644
> index 000000000000..24808fc2c7e3
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/usb/snps,dwc3.yaml
> @@ -0,0 +1,295 @@
> +# SPDX-License-Identifier: GPL-2.0
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/usb/snps,dwc3.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Synopsys DesignWare USB3 Controller
> +
> +maintainers:
> + - Felipe Balbi <balbi@kernel.org>
> +
> +description: |
> + This is usually a subnode to DWC3 glue to which it is connected, but can also
> + be presented as a standalone DT node with an optional vendor-specific
> + compatible string.
> +
> +allOf:
> + - $ref: "usb-xhci.yaml#"
> +
> +properties:
> + compatible:
> + contains:
> + const: "snps,dwc3"

Don't need quotes

> +
> + interrupts:
> + minItems: 1
> + maxItems: 3
> +
> + clocks:
> + description: |
> + In general the core supports three types of clocks. bus_clk_early is a

s/bus_clk_early/bus_early/

And the others too.

> + SoC Bus Clock (AHB/AXI/Native). ref_clk generates ITP when the UTMI/ULPI
> + PHY is suspended. suspend_clk clocks a small part of the USB3 core when
> + SS PHY in P3. But particular cases may differ from that having less or
> + more clock sources with another names.
> +
> + clock-names:
> + contains:
> + anyOf:
> + - enum: ["bus_early", "ref", "suspend"]
> + - true

That's unfortunate...

> +
> + usb-phy:
> + minItems: 1
> + items:
> + - description: USB2/HS PHY
> + - description: USB3/SS PHY
> +
> + phys:
> + minItems: 1
> + items:
> + - description: USB2/HS PHY
> + - description: USB3/SS PHY
> +
> + phy-names:
> + minItems: 1
> + items:
> + - const: usb2-phy
> + - const: usb3-phy
> +
> + resets:
> + minItems: 1
> +
> + snps,usb2-lpm-disable:
> + description: Indicate if we don't want to enable USB2 HW LPM
> + type: boolean
> +
> + snps,usb3_lpm_capable:
> + description: Determines if platform is USB3 LPM capable
> + type: boolean
> +
> + snps,dis-start-transfer-quirk:
> + description: |

Drop '|'.

> + When set, disable isoc START TRANSFER command failure SW work-around
> + for DWC_usb31 version 1.70a-ea06 and prior.
> + type: boolean
> +
> + snps,disable_scramble_quirk:
> + description: |
> + True when SW should disable data scrambling. Only really useful for FPGA
> + builds.
> + type: boolean
> +
> + snps,has-lpm-erratum:
> + description: True when DWC3 was configured with LPM Erratum enabled
> + type: boolean
> +
> + snps,lpm-nyet-threshold:
> + description: LPM NYET threshold
> + $ref: /schemas/types.yaml#/definitions/uint8
> +
> + snps,u2exit_lfps_quirk:
> + description: Set if we want to enable u2exit lfps quirk
> + type: boolean
> +
> + snps,u2ss_inp3_quirk:
> + description: Set if we enable P3 OK for U2/SS Inactive quirk
> + type: boolean
> +
> + snps,req_p1p2p3_quirk:
> + description: |
> + When set, the core will always request for P1/P2/P3 transition sequence.
> + type: boolean
> +
> + snps,del_p1p2p3_quirk:
> + description: |
> + When set core will delay P1/P2/P3 until a certain amount of 8B10B errors
> + occur.
> + type: boolean
> +
> + snps,del_phy_power_chg_quirk:
> + description: When set core will delay PHY power change from P0 to P1/P2/P3.
> + type: boolean
> +
> + snps,lfps_filter_quirk:
> + description: When set core will filter LFPS reception.
> + type: boolean
> +
> + snps,rx_detect_poll_quirk:
> + description: |
> + when set core will disable a 400us delay to start Polling LFPS after
> + RX.Detect.
> + type: boolean
> +
> + snps,tx_de_emphasis_quirk:
> + description: When set core will set Tx de-emphasis value
> + type: boolean
> +
> + snps,tx_de_emphasis:
> + description: |
> + The value driven to the PHY is controlled by the LTSSM during USB3
> + Compliance mode.
> + $ref: /schemas/types.yaml#/definitions/uint8
> +
> + snps,dis_u3_susphy_quirk:
> + description: When set core will disable USB3 suspend phy
> + type: boolean
> +
> + snps,dis_u2_susphy_quirk:
> + description: When set core will disable USB2 suspend phy
> + type: boolean
> +
> + snps,dis_enblslpm_quirk:
> + description: |
> + When set clears the enblslpm in GUSB2PHYCFG, disabling the suspend signal
> + to the PHY.
> + type: boolean
> +
> + snps,dis-u1-entry-quirk:
> + description: Set if link entering into U1 needs to be disabled
> + type: boolean
> +
> + snps,dis-u2-entry-quirk:
> + description: Set if link entering into U2 needs to be disabled
> + type: boolean
> +
> + snps,dis_rxdet_inp3_quirk:
> + description: |
> + When set core will disable receiver detection in PHY P3 power state.
> + type: boolean
> +
> + snps,dis-u2-freeclk-exists-quirk:
> + description: |
> + When set, clear the u2_freeclk_exists in GUSB2PHYCFG, specify that USB2
> + PHY doesn't provide a free-running PHY clock.
> + type: boolean
> +
> + snps,dis-del-phy-power-chg-quirk:
> + description: |
> + When set core will change PHY power from P0 to P1/P2/P3 without delay.
> + type: boolean
> +
> + snps,dis-tx-ipgap-linecheck-quirk:
> + description: When set, disable u2mac linestate check during HS transmit
> + type: boolean
> +
> + snps,parkmode-disable-ss-quirk:
> + description: |
> + When set, all SuperSpeed bus instances in park mode are disabled.
> + type: boolean
> +
> + snps,dis_metastability_quirk:
> + description: |
> + When set, disable metastability workaround. CAUTION! Use only if you are
> + absolutely sure of it.
> + type: boolean
> +
> + snps,is-utmi-l1-suspend:
> + description: |
> + True when DWC3 asserts output signal utmi_l1_suspend_n, false when
> + asserts utmi_sleep_n.
> + type: boolean
> +
> + snps,hird-threshold:
> + description: HIRD threshold
> + $ref: /schemas/types.yaml#/definitions/uint8
> +
> + snps,hsphy_interface:
> + description: |
> + High-Speed PHY interface selection between UTMI+ and ULPI when the
> + DWC_USB3_HSPHY_INTERFACE has value 3.
> + $ref: /schemas/types.yaml#/definitions/uint8
> + enum: ["utmi", "ulpi"]
> +
> + snps,quirk-frame-length-adjustment:
> + description: |
> + Value for GFLADJ_30MHZ field of GFLADJ register for post-silicon frame
> + length adjustment when the fladj_30mhz_sdbnd signal is invalid or
> + incorrect.
> + $ref: /schemas/types.yaml#/definitions/uint32
> +
> + snps,rx-thr-num-pkt-prd:
> + description: |
> + Periodic ESS RX packet threshold count (host mode only). Set this and
> + snps,rx-max-burst-prd to a valid, non-zero value 1-16 (DWC_usb31
> + programming guide section 1.2.4) to enable periodic ESS RX threshold.
> + $ref: /schemas/types.yaml#/definitions/uint8
> + minimum: 1
> + maximum: 16
> +
> + snps,rx-max-burst-prd:
> + description: |
> + Max periodic ESS RX burst size (host mode only). Set this and
> + snps,rx-thr-num-pkt-prd to a valid, non-zero value 1-16 (DWC_usb31
> + programming guide section 1.2.4) to enable periodic ESS RX threshold.
> + $ref: /schemas/types.yaml#/definitions/uint8
> + minimum: 1
> + maximum: 16
> +
> + snps,tx-thr-num-pkt-prd:
> + description: |
> + Periodic ESS TX packet threshold count (host mode only). Set this and
> + snps,tx-max-burst-prd to a valid, non-zero value 1-16 (DWC_usb31
> + programming guide section 1.2.3) to enable periodic ESS TX threshold.
> + $ref: /schemas/types.yaml#/definitions/uint8
> + minimum: 1
> + maximum: 16
> +
> + snps,tx-max-burst-prd:
> + description: |
> + Max periodic ESS TX burst size (host mode only). Set this and
> + snps,tx-thr-num-pkt-prd to a valid, non-zero value 1-16 (DWC_usb31
> + programming guide section 1.2.3) to enable periodic ESS TX threshold.
> + $ref: /schemas/types.yaml#/definitions/uint8
> + minimum: 1
> + maximum: 16
> +
> + tx-fifo-resize:
> + description: Determines if the FIFO *has* to be reallocated
> + deprecated: true
> + type: boolean
> +
> + snps,incr-burst-type-adjustment:
> + description: |
> + Value for INCR burst type of GSBUSCFG0 register, undefined length INCR
> + burst type enable and INCRx type. A single value means INCRX burst mode
> + enabled. If more than one value specified, undefined length INCR burst
> + type will be enabled with burst lengths utilized up to the maximum
> + of the values passed in this property.
> + $ref: /schemas/types.yaml#/definitions/uint32-array
> + minItems: 1
> + maxItems: 8
> + uniqueItems: true
> + items:
> + enum: [1, 4, 8, 16, 32, 64, 128, 256]
> +
> +unevaluatedProperties: false
> +
> +required:
> + - compatible
> + - reg
> + - interrupts
> +
> +examples:
> + - |
> + usb@4a030000 {
> + compatible = "snps,dwc3";
> + reg = <0x4a030000 0xcfff>;
> + interrupts = <0 92 4>;
> + usb-phy = <&usb2_phy>, <&usb3_phy>;
> + snps,incr-burst-type-adjustment = <1>, <4>, <8>, <16>;
> + };
> + - |
> + usb@4a000000 {
> + compatible = "snps,dwc3";
> + reg = <0x4a000000 0xcfff>;
> + interrupts = <0 92 4>;
> + clocks = <&clk 1>, <&clk 2>, <&clk 3>;
> + clock-names = "bus_early", "ref", "suspend";
> + phys = <&usb2_phy>, <&usb3_phy>;
> + phy-names = "usb2-phy", "usb3-phy";
> + snps,dis_u2_susphy_quirk;
> + snps,dis_enblslpm_quirk;
> + };
> +...
> --
> 2.27.0
>

\
 
 \ /
  Last update: 2020-10-13 14:37    [W:0.400 / U:3.184 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site