lkml.org 
[lkml]   [2020]   [Jan]   [8]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH 2/2] PM / devfreq: Add devfreq_transitions debugfs file
From
Date
Hi,

On 1/8/20 2:20 PM, Dmitry Osipenko wrote:
> 08.01.2020 00:48, Bjorn Andersson пишет:
>> On Tue 07 Jan 01:05 PST 2020, Chanwoo Choi wrote:
>>
>>> Add new devfreq_transitions debugfs file to track the frequency transitions
>>> of all devfreq devices for the simple profiling as following:
>>> - /sys/kernel/debug/devfreq/devfreq_transitions
>>>
>>> And the user can decide the storage size (CONFIG_NR_DEVFREQ_TRANSITIONS)
>>> in Kconfig in order to save the transition history.
>>>
>>> [Detailed description of each field of 'devfreq_transitions' debugfs file]
>>> - time_ms : Change time of frequency transition. (unit: millisecond)
>>> - dev_name : Device name of h/w.
>>> - dev : Device name made by devfreq core.
>>> - parent_dev : If devfreq device uses the passive governor,
>>> show parent devfreq device name.
>>> - load_% : If devfreq device uses the simple_ondemand governor,
>>> load is used by governor whene deciding the new frequency.
>>> (unit: percentage)
>>> - old_freq_hz : Frequency before changing. (unit: hz)
>>> - new_freq_hz : Frequency after changed. (unit: hz)
>>>
>>> [For example on Exynos5422-based Odroid-XU3 board]
>>> $ cat /sys/kernel/debug/devfreq/devfreq_transitions
>>> time_ms dev_name dev parent_dev load_% old_freq_hz new_freq_hz
>>> ---------- ------------------------------ ---------- ---------- ---------- ------------ ------------
>>> 14600 soc:bus_noc devfreq2 devfreq1 0 100000000 67000000
>>> 14600 soc:bus_fsys_apb devfreq3 devfreq1 0 200000000 100000000
>>> 14600 soc:bus_fsys devfreq4 devfreq1 0 200000000 100000000
>>> 14600 soc:bus_fsys2 devfreq5 devfreq1 0 150000000 75000000
>>> 14602 soc:bus_mfc devfreq6 devfreq1 0 222000000 96000000
>>> 14602 soc:bus_gen devfreq7 devfreq1 0 267000000 89000000
>>> 14602 soc:bus_g2d devfreq9 devfreq1 0 300000000 84000000
>>> 14602 soc:bus_g2d_acp devfreq10 devfreq1 0 267000000 67000000
>>> 14602 soc:bus_jpeg devfreq11 devfreq1 0 300000000 75000000
>>> 14602 soc:bus_jpeg_apb devfreq12 devfreq1 0 167000000 84000000
>>> 14603 soc:bus_disp1_fimd devfreq13 devfreq1 0 200000000 120000000
>>> 14603 soc:bus_disp1 devfreq14 devfreq1 0 300000000 120000000
>>> 14606 soc:bus_gscl_scaler devfreq15 devfreq1 0 300000000 150000000
>>> 14606 soc:bus_mscl devfreq16 devfreq1 0 333000000 84000000
>>> 14608 soc:bus_wcore devfreq1 9 333000000 84000000
>>> 14783 10c20000.memory-controller devfreq0 35 825000000 633000000
>>> 15873 soc:bus_wcore devfreq1 41 84000000 400000000
>>> 15873 soc:bus_noc devfreq2 devfreq1 0 67000000 100000000
>>> [snip]
>>>
>>
>> Wouldn't it make more sense to expose this through the tracing
>> framework - like many other subsystems does?
>
> I think devfreq core already has some tracing support and indeed it
> should be better to extend it rather than duplicate.
>

In my opinion this debugfs interface should be considered as a helpful
validation entry point. We had some issues with wrong bootloader
configurations in clock tree, where some frequencies could not be set
in the kernel. Similar useful description can be find in clock subsystem
where there is clock tree summary file.

It is much cheaper to poke a few files in debug dir by some automated
test than starting tracing, provoking desired code flow in the
devfreq for every device, paring the results... A simple boot test
which reads only these new files can be enough to rise the flag.
Secondly the tracing is not always compiled.

It could capture old/wrong bootloaders which pinned devices
improperly to PLLs or wrong DT values in OPP table.
(a workaround for Odroid xu4 patchset:
https://lkml.org/lkml/2019/7/15/276
)

Chanwoo what do think about some sanity check summary?
It could be presented in a 3rd file: 'devfreq_sanity', which
could report if the devices could set their registered OPPs
and got the same values, i.e. set 166MHz --> set to 150MHz
in reality. If a config option i.e. DEVFREQ_SANITY is set
then during the registration of a new device it checks OPPs
if they are possible to set. It could be done before assigning
the governor for the device and results present in of of your files.

Regards,
Lukasz


\
 
 \ /
  Last update: 2020-01-08 16:44    [W:0.092 / U:1.116 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site