lkml.org 
[lkml]   [2020]   [Jan]   [8]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH v6 2/2] spi: cadence-quadpsi: Add support for the Cadence QSPI controller
From
Date
Hi,

Thank you for the review  comments and your time.

On 8/1/2020 1:25 PM, Vignesh Raghavendra wrote:
> Hi,
> [...]
> On 30/12/19 1:11 pm, Ramuthevar,Vadivel MuruganX wrote:
>> +static int cqspi_probe(struct platform_device *pdev)
>> +{
>> + struct device *dev = &pdev->dev;
>> + struct struct_cqspi *cqspi;
>> + struct spi_master *master;
>> + struct reset_control *rstc, *rstc_ocp;
>> + const struct cqspi_driver_platdata *ddata;
>> + struct cqspi_platform_data *pdata = NULL;
>> + struct resource *res = NULL;
>> + int ret;
>> +
>> + master = spi_alloc_master(&pdev->dev, sizeof(*cqspi));
>> + if (!master) {
>> + dev_err(&pdev->dev, "spi_alloc_master failed\n");
>> + return -ENOMEM;
>> + }
>> + master->mode_bits = SPI_RX_QUAD | SPI_TX_DUAL | SPI_RX_DUAL |
>> + SPI_RX_OCTAL;
>> + master->setup = cqspi_setup;
>> + master->mem_ops = &cqspi_mem_ops;
>> + master->dev.of_node = pdev->dev.of_node;
>> + cqspi = spi_master_get_devdata(master);
>> + cqspi->pdev = pdev;
>> +
>> + pdata = devm_kmalloc(&pdev->dev, sizeof(*pdata), GFP_KERNEL);
> devm_kzalloc()?
Noted, will fix it.
>> + if (!pdata)
>> + return -ENOMEM;
>> +
>> + pdev->dev.platform_data = pdata;
>> +
>> + /* Obtain QSPI clock. */
>> + cqspi->clk = devm_clk_get(&pdev->dev, "qspi");
> clock-name of "qspi" is not mandatory as per DT binding and current DT
> files don't have clock-names property. This therefore cause probe to
> fail. This should remain:
>
> cqspi->clk = devm_clk_get(&pdev->dev, "NULL");
sure , I will add NULL instead of "qspi"
>> + if (IS_ERR(cqspi->clk)) {
>> + dev_err(&pdev->dev, "cannot get qspi clk\n");
>> + return PTR_ERR(cqspi->clk);
>> + }
>> + pdata->master_ref_clk_hz = clk_get_rate(cqspi->clk);
>> +
>> + ret = clk_prepare_enable(cqspi->clk);
>> + if (ret < 0) {
>> + dev_err(&pdev->dev, "failed to enable qspi clock: %d\n", ret);
>> + return ret;
>> + }
>> +
>> + /* Obtain configuration from OF. */
>> + ret = cqspi_of_get_pdata(pdev);
>> + if (ret) {
>> + dev_err(&pdev->dev, "Get platform data failed.\n");
>> + return -ENODEV;
>> + }
>> +
>> + cqspi->res = res;
>> + /* Obtain and remap controller address. */
>> + res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
>> + cqspi->iobase = devm_ioremap_resource(&pdev->dev, res);
>> + if (IS_ERR(cqspi->iobase)) {
>> + dev_err(dev, "Cannot remap controller address.\n");
>> + return PTR_ERR(cqspi->iobase);
>> + }
>> +
>> + /* Obtain and remap AHB address. */
>> + res = platform_get_resource(pdev, IORESOURCE_MEM, 1);
>> + cqspi->qspi_ahb_virt = devm_ioremap_resource(dev, res);
>> + if (IS_ERR(cqspi->qspi_ahb_virt)) {
>> + dev_err(dev, "Cannot remap AHB address.\n");
>> + return PTR_ERR(cqspi->qspi_ahb_virt);
>> + }
>> + cqspi->ahbbase = res;
>> + cqspi->ahb_size = resource_size(res);
>> +
>> + /* Obtain QSPI reset control */
>> + rstc = devm_reset_control_get_optional_exclusive(dev, "qspi");
>> + if (IS_ERR(rstc)) {
>> + dev_err(dev, "Cannot get QSPI reset.\n");
>> + return PTR_ERR(rstc);
>> + }
>> +
>> + rstc_ocp = devm_reset_control_get_optional_exclusive(dev, "qspi-ocp");
>> + if (IS_ERR(rstc_ocp)) {
>> + dev_err(dev, "Cannot get QSPI OCP reset.\n");
>> + return PTR_ERR(rstc_ocp);
>> + }
>> +
>> + reset_control_assert(rstc);
>> + reset_control_deassert(rstc);
>> +
>> + reset_control_assert(rstc_ocp);
>> + reset_control_deassert(rstc_ocp);
>> +
>> + ddata = of_device_get_match_data(dev);
>> + if (ddata && (ddata->quirks & CQSPI_NEEDS_WR_DELAY))
>> + cqspi->wr_delay = 5 * DIV_ROUND_UP(NSEC_PER_SEC,
>> + pdata->master_ref_clk_hz);
>> +
>> + if (ddata && (ddata->quirks & CQSPI_DISABLE_DAC_MODE))
>> + cqspi->use_dac_mode = false;
>> +
>> + init_completion(&cqspi->transfer_complete);
>> +
>> + /* Obtain IRQ line. */
>> + cqspi->irq = platform_get_irq(pdev, 0);
>> + if (cqspi->irq < 0) {
>> + dev_err(dev, "platform_get_irq failed.\n");
>> + ret = -ENXIO;
>> + }
>> + ret = devm_request_irq(dev, cqspi->irq, cqspi_irq_handler, 0,
>> + pdev->name, cqspi);
>> + if (ret) {
>> + dev_err(dev, "request_irq failed.\n");
>> + goto out_clk_disable;
>> + }
>> +
>> + master->bus_num = pdata->bus_num;
>> + master->num_chipselect = pdata->num_chipselect;
> Where is pdata->bus_num and pdata->num_chipselect initialized? This
> causes devm_spi_register_master() to fail randomly as num_chipselect may
> be 0.
Agreed!, I also observed the issue after sending the patches , will fix
it in the next patch-set.
Regards
Vadivel
>> + mutex_init(&cqspi->lock);
>> + platform_set_drvdata(pdev, master);
>> + cqspi_controller_init(cqspi);
>> + cqspi->current_cs = -1;
>> +
>> + ret = devm_spi_register_master(dev, master);
>> + if (ret) {
>> + dev_err(&pdev->dev, "devm_spi_register_master failed.\n");
>> + goto err_of;
>> + }
>> +
>> + return 0;
>> +
>> +out_clk_disable:
>> + clk_disable_unprepare(cqspi->clk);
>> +err_of:
>> + spi_master_put(master);
>> + dev_err(&pdev->dev, "Cadence QSPI controller probe failed\n");
>> + return ret;
>> +}
>> +

\
 
 \ /
  Last update: 2020-01-08 06:57    [W:0.093 / U:0.080 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site