lkml.org 
[lkml]   [2020]   [Jan]   [8]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v3 3/4] dt-bindings: power: Add the bq2515x family dt bindings
Date
Add the bindings for the bq25150 and bq25155 500mA
charging ICs from Texas Instruments.

Datasheet:
http://www.ti.com/lit/ds/symlink/bq25150.pdf
http://www.ti.com/lit/ds/symlink/bq25155.pdf

CC: Rob Herring <robh@kernel.org>
Signed-off-by: Dan Murphy <dmurphy@ti.com>
---
v3 - Updated the constant-charge voltage binding to what is declared in
battery.txt

.../bindings/power/supply/bq2515x.yaml | 85 +++++++++++++++++++
1 file changed, 85 insertions(+)
create mode 100644 Documentation/devicetree/bindings/power/supply/bq2515x.yaml

diff --git a/Documentation/devicetree/bindings/power/supply/bq2515x.yaml b/Documentation/devicetree/bindings/power/supply/bq2515x.yaml
new file mode 100644
index 000000000000..670952021e8d
--- /dev/null
+++ b/Documentation/devicetree/bindings/power/supply/bq2515x.yaml
@@ -0,0 +1,85 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+# Copyright (C) 2019 Texas Instruments Incorporated
+%YAML 1.2
+---
+$id: "http://devicetree.org/schemas/power/supply/bq2515x.yaml#"
+$schema: "http://devicetree.org/meta-schemas/core.yaml#"
+
+title: TI bq2515x 500-mA Linear charger family
+
+maintainers:
+ - Dan Murphy <dmurphy@ti.com>
+
+description: |
+ The BQ2515x family is a highly integrated battery charge management IC that
+ integrates the most common functions for wearable devices, namely a charger,
+ an output voltage rail, ADC for battery and system monitoring, and
+ push-button controller.
+
+ Specifications about the charger can be found at:
+ http://www.ti.com/lit/ds/symlink/bq25150.pdf
+ http://www.ti.com/lit/ds/symlink/bq25155.pdf
+
+properties:
+ compatible:
+ enum:
+ - ti,bq25150
+ - ti,bq25155
+
+ reg:
+ maxItems: 1
+
+ pg-gpios:
+ description: |
+ GPIO used for connecting the bq2515x device PG (Power Good)
+ pin. This pin should be used if possible as this is the
+ recommended way to obtain the charger's input PG state.
+ If this pin is not specified a software-based approach for PG
+ detection is used.
+
+ reset-gpios:
+ description: |
+ GPIO used for hardware reset.
+
+ low-power-gpios:
+ description: |
+ GPIO used for low power mode of IC.
+
+ charge-enable-gpios:
+ description: |
+ GPIO used to turn on and off charging.
+
+ constant-charge-current-max-microamp:
+ description: |
+ Maximum charging current in micro Amps.
+ minimum: 50000
+ maximum: 600000
+
+ constant-charge-voltage-max-microvolt:
+ description: |
+ Maximum charging voltage in micro volts.
+ minimum: 3600000
+ maximum: 4600000
+
+required:
+ - compatible
+ - reg
+
+examples:
+ - |
+ #include <dt-bindings/gpio/gpio.h>
+ i2c0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ charger@6b {
+ compatible = "ti,bq25150";
+ reg = <0x6b>;
+
+ pg-gpios = <&gpio1 28 GPIO_ACTIVE_HIGH>;
+ reset-gpios = <&gpio0 14 GPIO_ACTIVE_HIGH>;
+ low-power-gpios = <&gpio0 15 GPIO_ACTIVE_HIGH>;
+ charge-enable-gpios = <&gpio0 13 GPIO_ACTIVE_LOW>;
+ constant-charge-current-max-microamp = <300000>;
+ voltage-max-design-microvolt = <4200000>;
+ };
+ };
--
2.23.0
\
 
 \ /
  Last update: 2020-01-08 21:26    [W:0.061 / U:3.540 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site