lkml.org 
[lkml]   [2019]   [Sep]   [6]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v4] watchdog: qcom: support pre-timeout when the bark irq is available
On Thu 05 Sep 14:00 PDT 2019, Jorge Ramirez-Ortiz wrote:
> diff --git a/drivers/watchdog/qcom-wdt.c b/drivers/watchdog/qcom-wdt.c
[..]
> +static inline int qcom_get_enable(struct watchdog_device *wdd)
> +{
> + int enable = QCOM_WDT_ENABLE;
> +
> + if (wdd->info->options & WDIOF_PRETIMEOUT)
> + enable |= QCOM_WDT_ENABLE_IRQ;

Looking at downstream they conditionally write 3 to WDT_EN during
initialization, but during suspend/resume they just set it to back to 1.

So I don't think you should touch BIT(1) (which name doesn't match
downstream or the register documentation)

> +
> + return enable;
> +}
> +
> +static irqreturn_t qcom_wdt_isr(int irq, void *arg)
> +{
> + struct watchdog_device *wdd = arg;
> +
> + watchdog_notify_pretimeout(wdd);
> +
> + return IRQ_HANDLED;
> +}
> +
> static int qcom_wdt_start(struct watchdog_device *wdd)
> {
> struct qcom_wdt *wdt = to_qcom_wdt(wdd);
> + unsigned int bark = wdd->timeout;
> +
> + if (wdd->pretimeout)
> + bark = bark - wdd->pretimeout;

As Guenter points out, writing wdd->timeout - wdt->pretimeout to
WDT_BARK_TIME unconditionally should do the trick.

>
> writel(0, wdt_addr(wdt, WDT_EN));
> writel(1, wdt_addr(wdt, WDT_RST));
> - writel(wdd->timeout * wdt->rate, wdt_addr(wdt, WDT_BARK_TIME));
> + writel(bark * wdt->rate, wdt_addr(wdt, WDT_BARK_TIME));
> writel(wdd->timeout * wdt->rate, wdt_addr(wdt, WDT_BITE_TIME));
> - writel(1, wdt_addr(wdt, WDT_EN));
> + writel(qcom_get_enable(wdd), wdt_addr(wdt, WDT_EN));
> return 0;
> }
[..]
> @@ -204,7 +248,17 @@ static int qcom_wdt_probe(struct platform_device *pdev)
> return -EINVAL;
> }
>
> - wdt->wdd.info = &qcom_wdt_info;
> + irq = platform_get_irq(pdev, 0);
> + if (irq > 0) {
> + if (devm_request_irq(dev, irq, qcom_wdt_isr,
> + IRQF_TRIGGER_RISING, "wdt_bark",
> + &wdt->wdd))

A failure here means that a irq was specified in DT (platform_get_irq()
returned > 0) but you failed to acquire request it, you should fail your
probe() when this happens.

> + irq = 0;
> + } else if (irq == -EPROBE_DEFER)
> + return -EPROBE_DEFER;

Some {} around this block please.

Regards,
Bjorn

> +
> + wdt->wdd.info = irq > 0 ? &qcom_wdt_pt_info : &qcom_wdt_info;
> + wdt->wdd.pretimeout = irq > 0 ? 1 : 0;
> wdt->wdd.ops = &qcom_wdt_ops;
> wdt->wdd.min_timeout = 1;
> wdt->wdd.max_timeout = 0x10000000U / wdt->rate;
> --
> 2.23.0
>

\
 
 \ /
  Last update: 2019-09-06 19:41    [W:0.039 / U:1.388 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site