lkml.org 
[lkml]   [2019]   [Sep]   [6]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v4] watchdog: qcom: support pre-timeout when the bark irq is available
On Thu, Sep 05, 2019 at 11:34:03PM +0200, Jorge Ramirez wrote:
> On 9/5/19 23:19, Guenter Roeck wrote:
> > On Thu, Sep 05, 2019 at 11:00:35PM +0200, Jorge Ramirez-Ortiz wrote:
> >> Use the bark interrupt as the pre-timeout notifier whenever this
> >> interrupt is available.
> >>
> >> By default, the pretimeout notification shall occur one second earlier
> >> than the timeout.
> >>
> >> Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
> >> ---
> >> v4:
> >> address Guenter Roeck comments as follows:
> >> remove unnecessary include and private variable
> >> provide macro for WDT EN register values
> >> use pretimeout as per its API intent
> >> handle EPROBE_DEFER on get_irq
> >> also:
> >> handle the irq registration as done in pm8916_wdt.c
> >> v3:
> >> remove unnecesary variable added to private.
> >>
> >> v2:
> >> register the pre-timeout notifier instead.
> >>
> >> v1:
> >> drivers/watchdog/qcom-wdt.c | 64 ++++++++++++++++++++++++++++++++++---
> >> 1 file changed, 59 insertions(+), 5 deletions(-)
> >>
> >> diff --git a/drivers/watchdog/qcom-wdt.c b/drivers/watchdog/qcom-wdt.c
> >> index 7be7f87be28f..0f1d29eeb81d 100644
> >> --- a/drivers/watchdog/qcom-wdt.c
> >> +++ b/drivers/watchdog/qcom-wdt.c
> >> @@ -10,6 +10,7 @@
> >> #include <linux/platform_device.h>
> >> #include <linux/watchdog.h>
> >> #include <linux/of_device.h>
> >> +#include <linux/interrupt.h>
> >>
> >> enum wdt_reg {
> >> WDT_RST,
> >> @@ -19,6 +20,9 @@ enum wdt_reg {
> >> WDT_BITE_TIME,
> >> };
> >>
> >> +#define QCOM_WDT_ENABLE BIT(0)
> >> +#define QCOM_WDT_ENABLE_IRQ BIT(1)
> >> +
> >
> > Using BIT() requires "#include <linux/bits.h>".
>
> do you want it explicitly in the file even if it builds?
>

May I kindly suggest to read Documentation/process/submit-checklist.rst ?

> >
> >> static const u32 reg_offset_data_apcs_tmr[] = {
> >> [WDT_RST] = 0x38,
> >> [WDT_EN] = 0x40,
> >> @@ -54,15 +58,38 @@ struct qcom_wdt *to_qcom_wdt(struct watchdog_device *wdd)
> >> return container_of(wdd, struct qcom_wdt, wdd);
> >> }
> >>
> >> +static inline int qcom_get_enable(struct watchdog_device *wdd)
> >> +{
> >> + int enable = QCOM_WDT_ENABLE;
> >> +
> >> + if (wdd->info->options & WDIOF_PRETIMEOUT)
> >> + enable |= QCOM_WDT_ENABLE_IRQ;
> >> +
> >
> > Again, the condition needs to be that pretimeout != 0,
> > not that it is supported.
>
> no I dont think so. doing that would propagate a possible error in some
> pretimeout setup code which would end up enabling an interrupt when it
> shouldnt. so I dont think that doing that would be correct.
>
If the pretimeout setup code is buggy, it needs to be fixed.

> The interrupt should only be enabled if WDIOF_PRETIMEOUT is configured
> (independently of the pretimeout value); as a matter of fact, if
> pretimeout is 0, the interrupt will trigger at the same time than bark
> (which is what the original code used to do).
>
The original code did not set bit 1 of the WDT_EN register,
and it did not set the bark time.

> so I'd rather keep this condition unless you strongly oppose to it.
>

Please feel free to petition to Wim.

> >
> >> + return enable;
> >> +}
> >> +
> >> +static irqreturn_t qcom_wdt_isr(int irq, void *arg)
> >> +{
> >> + struct watchdog_device *wdd = arg;
> >> +
> >> + watchdog_notify_pretimeout(wdd);
> >> +
> >> + return IRQ_HANDLED;
> >> +}
> >> +
> >> static int qcom_wdt_start(struct watchdog_device *wdd)
> >> {
> >> struct qcom_wdt *wdt = to_qcom_wdt(wdd);
> >> + unsigned int bark = wdd->timeout;
> >> +
> >> + if (wdd->pretimeout)
> >> + bark = bark - wdd->pretimeout;
> >
> > The if() just adds code and doesn't otherwise do any good.
>
> yeah, was just for clarity and it is surely removed by the compiler. but
> sure will remove
>
> >
> >>
> >> writel(0, wdt_addr(wdt, WDT_EN));
> >> writel(1, wdt_addr(wdt, WDT_RST));
> >> - writel(wdd->timeout * wdt->rate, wdt_addr(wdt, WDT_BARK_TIME));
> >> + writel(bark * wdt->rate, wdt_addr(wdt, WDT_BARK_TIME));
> >> writel(wdd->timeout * wdt->rate, wdt_addr(wdt, WDT_BITE_TIME));
> >> - writel(1, wdt_addr(wdt, WDT_EN));
> >> + writel(qcom_get_enable(wdd), wdt_addr(wdt, WDT_EN));
> >> return 0;
> >> }
> >>
> >> @@ -89,6 +116,13 @@ static int qcom_wdt_set_timeout(struct watchdog_device *wdd,
> >> return qcom_wdt_start(wdd);
> >> }
> >>
> >> +static int qcom_wdt_set_pretimeout(struct watchdog_device *wdd,
> >> + unsigned int timeout)
> >> +{
> >> + wdd->pretimeout = timeout;
> >> + return qcom_wdt_start(wdd);
> >> +}
> >> +
> >> static int qcom_wdt_restart(struct watchdog_device *wdd, unsigned long action,
> >> void *data)
> >> {
> >> @@ -105,7 +139,7 @@ static int qcom_wdt_restart(struct watchdog_device *wdd, unsigned long action,
> >> writel(1, wdt_addr(wdt, WDT_RST));
> >> writel(timeout, wdt_addr(wdt, WDT_BARK_TIME));
> >> writel(timeout, wdt_addr(wdt, WDT_BITE_TIME));
> >> - writel(1, wdt_addr(wdt, WDT_EN));
> >> + writel(qcom_get_enable(wdd), wdt_addr(wdt, WDT_EN));
> >>
> >> /*
> >> * Actually make sure the above sequence hits hardware before sleeping.
> >> @@ -121,6 +155,7 @@ static const struct watchdog_ops qcom_wdt_ops = {
> >> .stop = qcom_wdt_stop,
> >> .ping = qcom_wdt_ping,
> >> .set_timeout = qcom_wdt_set_timeout,
> >> + .set_pretimeout = qcom_wdt_set_pretimeout,
> >> .restart = qcom_wdt_restart,
> >> .owner = THIS_MODULE,
> >> };
> >> @@ -133,6 +168,15 @@ static const struct watchdog_info qcom_wdt_info = {
> >> .identity = KBUILD_MODNAME,
> >> };
> >>
> >> +static const struct watchdog_info qcom_wdt_pt_info = {
> >> + .options = WDIOF_KEEPALIVEPING
> >> + | WDIOF_MAGICCLOSE
> >> + | WDIOF_SETTIMEOUT
> >> + | WDIOF_PRETIMEOUT
> >> + | WDIOF_CARDRESET,
> >> + .identity = KBUILD_MODNAME,
> >> +};
> >> +
> >> static void qcom_clk_disable_unprepare(void *data)
> >> {
> >> clk_disable_unprepare(data);
> >> @@ -146,7 +190,7 @@ static int qcom_wdt_probe(struct platform_device *pdev)
> >> struct device_node *np = dev->of_node;
> >> const u32 *regs;
> >> u32 percpu_offset;
> >> - int ret;
> >> + int irq, ret;
> >>
> >> regs = of_device_get_match_data(dev);
> >> if (!regs) {
> >> @@ -204,7 +248,17 @@ static int qcom_wdt_probe(struct platform_device *pdev)
> >> return -EINVAL;
> >> }
> >>
> >> - wdt->wdd.info = &qcom_wdt_info;
> >> + irq = platform_get_irq(pdev, 0);
> >> + if (irq > 0) {
> >> + if (devm_request_irq(dev, irq, qcom_wdt_isr,
> >> + IRQF_TRIGGER_RISING, "wdt_bark",
> >> + &wdt->wdd))
> >> + irq = 0;
> >> + } else if (irq == -EPROBE_DEFER)
> >> + return -EPROBE_DEFER;
> >> +
> >> + wdt->wdd.info = irq > 0 ? &qcom_wdt_pt_info : &qcom_wdt_info;
> >> + wdt->wdd.pretimeout = irq > 0 ? 1 : 0;
> >
> > Why repeat the conditional ? It seems to me that something like
> >
> > wdt->wdd.info = &qcom_wdt_info;
> > ...
> > if (irq > 0) {
> > wdt->wdd.info = &qcom_wdt_pt_info;
> > wdt->wdd.pretimeout = 1;
> > ...
> > }
> >
> > would be much easier and avoid the repeated conditionals.
>
> I agree. will change.
>
> >
> >> wdt->wdd.ops = &qcom_wdt_ops;
> >> wdt->wdd.min_timeout = 1;
> >> wdt->wdd.max_timeout = 0x10000000U / wdt->rate;
> >> --
> >> 2.23.0
> >>
> >
>

\
 
 \ /
  Last update: 2019-09-06 15:00    [W:0.038 / U:0.540 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site