lkml.org 
[lkml]   [2019]   [Sep]   [10]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH] ARM: dts: imx6dl: SolidRun: add phy node with 100Mb/s max-speed
Date
Cubox-i Solo/DualLite carrier board has 100Mb/s magnetics while the
Atheros AR8035 PHY on the MicroSoM v1.3 CPU module is a 1GbE PHY device.

Since commit 5502b218e001 ("net: phy: use phy_resolve_aneg_linkmode in
genphy_read_status") ethernet is broken on Cubox-i Solo/DualLite devices.

This adds a phy node to the MicroSoM DTS and a 100Mb/s max-speed limit
to the Cubox-i Solo/DualLite carrier DTS.

Signed-off-by: tinywrkb <tinywrkb@gmail.com>
---
This patch fixes ethernet on my Cubox-i2-300-D which is limited to 100Mb/s,
afaik due to the carrier board magnetics, and was since commit 5502b218e001
("net: phy: use phy_resolve_aneg_linkmode in genphy_read_status")

The AR8035 PHY on the CPU module reports to the driver as 1GbE capable
via MII_BSMR's BMSR_ESTATEN status bit, the auto-negotiation sets the
speed at 1GbE while the carrier board can't support it.
Same behavior with the generic phy_device and the at803x drivers.

While the PHY is on the CPU module board I added the max-speed limit to
the cubox-i carrier DTS as I suspect that if the Solo or DualLite v1.3
MicroSoM will be connected to a 1GbE capable carrier board then it would
work correctly with 1GbE.

I can confirm that this commit doesn't break networking on the my
Cubox-i4Pro Quad (i4P-300-D) with it's 1GbE capable carrier board, and
was tested separately with the generic phy_device and at803x drivers.

arch/arm/boot/dts/imx6dl-cubox-i.dts | 4 ++++
arch/arm/boot/dts/imx6qdl-sr-som.dtsi | 9 +++++++++
2 files changed, 13 insertions(+)

diff --git a/arch/arm/boot/dts/imx6dl-cubox-i.dts b/arch/arm/boot/dts/imx6dl-cubox-i.dts
index 2b1b3e193f53..cfc82513c78c 100644
--- a/arch/arm/boot/dts/imx6dl-cubox-i.dts
+++ b/arch/arm/boot/dts/imx6dl-cubox-i.dts
@@ -49,3 +49,7 @@
model = "SolidRun Cubox-i Solo/DualLite";
compatible = "solidrun,cubox-i/dl", "fsl,imx6dl";
};
+
+&ethphy {
+ max-speed = <100>;
+};
diff --git a/arch/arm/boot/dts/imx6qdl-sr-som.dtsi b/arch/arm/boot/dts/imx6qdl-sr-som.dtsi
index 6d7f6b9035bc..969bc96c3f99 100644
--- a/arch/arm/boot/dts/imx6qdl-sr-som.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-sr-som.dtsi
@@ -57,6 +57,15 @@
phy-reset-duration = <2>;
phy-reset-gpios = <&gpio4 15 GPIO_ACTIVE_LOW>;
status = "okay";
+ phy-handle = <&ethphy>;
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ ethphy: ethernet-phy@0 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <0>;
+ };
+ };
};

&iomuxc {
--
2.23.0
\
 
 \ /
  Last update: 2019-09-10 17:55    [W:0.138 / U:0.436 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site