lkml.org 
[lkml]   [2019]   [Aug]   [30]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v3 5/7] arm64: dts: mt8183: add usb and phy nodes
Date
Add USB related nodes for MT8183, set it as host mode by default.

Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
---
v2~v3: no changes
---
arch/arm64/boot/dts/mediatek/mt8183-evb.dts | 22 +++++++++
arch/arm64/boot/dts/mediatek/mt8183.dtsi | 55 +++++++++++++++++++++
2 files changed, 77 insertions(+)

diff --git a/arch/arm64/boot/dts/mediatek/mt8183-evb.dts b/arch/arm64/boot/dts/mediatek/mt8183-evb.dts
index d8e555cbb5d3..142ff52f0f42 100644
--- a/arch/arm64/boot/dts/mediatek/mt8183-evb.dts
+++ b/arch/arm64/boot/dts/mediatek/mt8183-evb.dts
@@ -6,7 +6,9 @@
*/

/dts-v1/;
+#include <dt-bindings/gpio/gpio.h>
#include "mt8183.dtsi"
+#include "mt6358.dtsi"

/ {
model = "MediaTek MT8183 evaluation board";
@@ -24,6 +26,16 @@
chosen {
stdout-path = "serial0:921600n8";
};
+
+ usb_vbus: regulator@0 {
+ compatible = "regulator-fixed";
+ regulator-name = "p0_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&pio 42 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ regulator-always-on;
+ };
};

&auxadc {
@@ -135,6 +147,16 @@

};

+&ssusb {
+ vusb33-supply = <&mt6358_vusb_reg>;
+ dr_mode = "host";
+ status = "okay";
+};
+
+&usb_host {
+ status = "okay";
+};
+
&uart0 {
status = "okay";
};
diff --git a/arch/arm64/boot/dts/mediatek/mt8183.dtsi b/arch/arm64/boot/dts/mediatek/mt8183.dtsi
index c2749c4631bc..28da334237c6 100644
--- a/arch/arm64/boot/dts/mediatek/mt8183.dtsi
+++ b/arch/arm64/boot/dts/mediatek/mt8183.dtsi
@@ -8,6 +8,7 @@
#include <dt-bindings/clock/mt8183-clk.h>
#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/phy/phy.h>
#include "mt8183-pinfunc.h"

/ {
@@ -372,6 +373,35 @@
status = "disabled";
};

+ ssusb: usb@11201000 {
+ compatible = "mediatek,mt8183-mtu3", "mediatek,mtu3";
+ reg = <0 0x11201000 0 0x2e00>,
+ <0 0x11203e00 0 0x0100>;
+ reg-names = "mac", "ippc";
+ interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_LOW>;
+ phys = <&u2port0 PHY_TYPE_USB2>,
+ <&u3port0 PHY_TYPE_USB3>;
+ clocks = <&infracfg CLK_INFRA_UNIPRO_SCK>,
+ <&infracfg CLK_INFRA_USB>;
+ clock-names = "sys_ck", "ref_ck";
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+ status = "disabled";
+
+ usb_host: xhci@11200000 {
+ compatible = "mediatek,mt8183-xhci",
+ "mediatek,mtk-xhci";
+ reg = <0 0x11200000 0 0x1000>;
+ reg-names = "mac";
+ interrupts = <GIC_SPI 73 IRQ_TYPE_LEVEL_LOW>;
+ clocks = <&infracfg CLK_INFRA_UNIPRO_SCK>,
+ <&infracfg CLK_INFRA_USB>;
+ clock-names = "sys_ck", "ref_ck";
+ status = "disabled";
+ };
+ };
+
audiosys: syscon@11220000 {
compatible = "mediatek,mt8183-audiosys", "syscon";
reg = <0 0x11220000 0 0x1000>;
@@ -384,6 +414,31 @@
reg = <0 0x11f10000 0 0x1000>;
};

+ u3phy: usb-phy@11f40000 {
+ compatible = "mediatek,mt8183-tphy",
+ "mediatek,generic-tphy-v2";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0 0x11f40000 0x1000>;
+ status = "okay";
+
+ u2port0: usb-phy@0 {
+ reg = <0x0 0x700>;
+ clocks = <&clk26m>;
+ clock-names = "ref";
+ #phy-cells = <1>;
+ status = "okay";
+ };
+
+ u3port0: usb-phy@0700 {
+ reg = <0x0700 0x900>;
+ clocks = <&clk26m>;
+ clock-names = "ref";
+ #phy-cells = <1>;
+ status = "okay";
+ };
+ };
+
mfgcfg: syscon@13000000 {
compatible = "mediatek,mt8183-mfgcfg", "syscon";
reg = <0 0x13000000 0 0x1000>;
--
2.23.0
\
 
 \ /
  Last update: 2019-08-30 09:42    [W:0.182 / U:3.936 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site