lkml.org 
[lkml]   [2019]   [Aug]   [20]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v2 4/7] arm64: dts: actions: Add uSD and eMMC support for Bubblegum96
Date
Add uSD and eMMC support for Bubblegum96 board based on Actions Semi
Owl SoC. SD0 is connected to uSD slot and SD2 is connected to eMMC.
Since there is no PMIC support added yet, fixed regulator has been
used as a regulator node.

Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
---
.../boot/dts/actions/s900-bubblegum-96.dts | 60 +++++++++++++++++++
1 file changed, 60 insertions(+)

diff --git a/arch/arm64/boot/dts/actions/s900-bubblegum-96.dts b/arch/arm64/boot/dts/actions/s900-bubblegum-96.dts
index 732daaa6e9d3..92376b71cb8f 100644
--- a/arch/arm64/boot/dts/actions/s900-bubblegum-96.dts
+++ b/arch/arm64/boot/dts/actions/s900-bubblegum-96.dts
@@ -12,6 +12,9 @@
model = "Bubblegum-96";

aliases {
+ mmc0 = &mmc0;
+ mmc1 = &mmc1;
+ mmc2 = &mmc2;
serial5 = &uart5;
};

@@ -23,6 +26,22 @@
device_type = "memory";
reg = <0x0 0x0 0x0 0x80000000>;
};
+
+ vcc_3v1: vcc-3v1 {
+ compatible = "regulator-fixed";
+ regulator-name = "fixed-3.1V";
+ regulator-min-microvolt = <3100000>;
+ regulator-max-microvolt = <3100000>;
+ regulator-always-on;
+ };
+
+ sd_vcc: sd-vcc {
+ compatible = "regulator-fixed";
+ regulator-name = "fixed-3.1V";
+ regulator-min-microvolt = <3100000>;
+ regulator-max-microvolt = <3100000>;
+ regulator-always-on;
+ };
};

&i2c0 {
@@ -241,6 +260,47 @@
bias-pull-up;
};
};
+
+ mmc0_default: mmc0_default {
+ pinmux {
+ groups = "sd0_d0_mfp", "sd0_d1_mfp", "sd0_d2_d3_mfp",
+ "sd0_cmd_mfp", "sd0_clk_mfp";
+ function = "sd0";
+ };
+ };
+
+ mmc2_default: mmc2_default {
+ pinmux {
+ groups = "nand0_d0_ceb3_mfp";
+ function = "sd2";
+ };
+ };
+};
+
+/* uSD */
+&mmc0 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_default>;
+ no-sdio;
+ no-mmc;
+ no-1-8-v;
+ cd-gpios = <&pinctrl 120 GPIO_ACTIVE_LOW>;
+ bus-width = <4>;
+ vmmc-supply = <&sd_vcc>;
+ vqmmc-supply = <&sd_vcc>;
+};
+
+/* eMMC */
+&mmc2 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc2_default>;
+ no-sdio;
+ no-sd;
+ non-removable;
+ bus-width = <8>;
+ vmmc-supply = <&vcc_3v1>;
};

&timer {
--
2.17.1
\
 
 \ /
  Last update: 2019-08-21 04:41    [W:0.049 / U:8.232 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site