lkml.org 
[lkml]   [2019]   [Aug]   [2]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH 4.9 163/223] tty: serial: cpm_uart - fix init when SMC is relocated
Date
[ Upstream commit 06aaa3d066db87e8478522d910285141d44b1e58 ]

SMC relocation can also be activated earlier by the bootloader,
so the driver's behaviour cannot rely on selected kernel config.

When the SMC is relocated, CPM_CR_INIT_TRX cannot be used.

But the only thing CPM_CR_INIT_TRX does is to clear the
rstate and tstate registers, so this can be done manually,
even when SMC is not relocated.

Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Fixes: 9ab921201444 ("cpm_uart: fix non-console port startup bug")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
drivers/tty/serial/cpm_uart/cpm_uart_core.c | 17 +++++++++++------
1 file changed, 11 insertions(+), 6 deletions(-)

diff --git a/drivers/tty/serial/cpm_uart/cpm_uart_core.c b/drivers/tty/serial/cpm_uart/cpm_uart_core.c
index 0040c29f651a..b9e137c03fe3 100644
--- a/drivers/tty/serial/cpm_uart/cpm_uart_core.c
+++ b/drivers/tty/serial/cpm_uart/cpm_uart_core.c
@@ -421,7 +421,16 @@ static int cpm_uart_startup(struct uart_port *port)
clrbits16(&pinfo->sccp->scc_sccm, UART_SCCM_RX);
}
cpm_uart_initbd(pinfo);
- cpm_line_cr_cmd(pinfo, CPM_CR_INIT_TRX);
+ if (IS_SMC(pinfo)) {
+ out_be32(&pinfo->smcup->smc_rstate, 0);
+ out_be32(&pinfo->smcup->smc_tstate, 0);
+ out_be16(&pinfo->smcup->smc_rbptr,
+ in_be16(&pinfo->smcup->smc_rbase));
+ out_be16(&pinfo->smcup->smc_tbptr,
+ in_be16(&pinfo->smcup->smc_tbase));
+ } else {
+ cpm_line_cr_cmd(pinfo, CPM_CR_INIT_TRX);
+ }
}
/* Install interrupt handler. */
retval = request_irq(port->irq, cpm_uart_int, 0, "cpm_uart", port);
@@ -875,16 +884,14 @@ static void cpm_uart_init_smc(struct uart_cpm_port *pinfo)
(u8 __iomem *)pinfo->tx_bd_base - DPRAM_BASE);

/*
- * In case SMC1 is being relocated...
+ * In case SMC is being relocated...
*/
-#if defined (CONFIG_I2C_SPI_SMC1_UCODE_PATCH)
out_be16(&up->smc_rbptr, in_be16(&pinfo->smcup->smc_rbase));
out_be16(&up->smc_tbptr, in_be16(&pinfo->smcup->smc_tbase));
out_be32(&up->smc_rstate, 0);
out_be32(&up->smc_tstate, 0);
out_be16(&up->smc_brkcr, 1); /* number of break chars */
out_be16(&up->smc_brkec, 0);
-#endif

/* Set up the uart parameters in the
* parameter ram.
@@ -898,8 +905,6 @@ static void cpm_uart_init_smc(struct uart_cpm_port *pinfo)
out_be16(&up->smc_brkec, 0);
out_be16(&up->smc_brkcr, 1);

- cpm_line_cr_cmd(pinfo, CPM_CR_INIT_TRX);
-
/* Set UART mode, 8 bit, no parity, one stop.
* Enable receive and transmit.
*/
--
2.20.1


\
 
 \ /
  Last update: 2019-08-02 11:51    [W:0.511 / U:1.076 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site