lkml.org 
[lkml]   [2019]   [Jul]   [9]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
Date
From
SubjectRe: [v4 1/6] dt-bindings: media: Document bindings for DW MIPI CSI-2 Host
Hi Luis,

On Mon, Jul 08, 2019 at 03:21:50PM +0000, Luis de Oliveira wrote:
> Hi Sakari,
>
> Thank you for your feedback.
> I have my comments inline.
>
> From: Sakari Ailus <sakari.ailus@iki.fi>
> Date: Fri, Jun 28, 2019 at 15:13:26
>
> > Hi Luis,
> >
> > Thank you for the patchset.
> >
> > On Tue, Jun 11, 2019 at 09:20:50PM +0200, Luis Oliveira wrote:
> > > From: Luis Oliveira <lolivei@synopsys.com>
> > >
> > > Add bindings for Synopsys DesignWare MIPI CSI-2 host.
> > >
> > > Signed-off-by: Luis Oliveira <lolivei@synopsys.com>
> > > ---
> > > Changelog
> > > v3-v4
> > > - remove "plat" from the block name @rob @laurent
> > > - remove "phy-names" when single-entry @rob
> > > - remove "snps,output-type" -> went to the driver config @laurent
> > >
> > > .../devicetree/bindings/media/snps,dw-csi.txt | 41 ++++++++++++++++++++++
> > > 1 file changed, 41 insertions(+)
> > > create mode 100644 Documentation/devicetree/bindings/media/snps,dw-csi.txt
> > >
> > > diff --git a/Documentation/devicetree/bindings/media/snps,dw-csi.txt b/Documentation/devicetree/bindings/media/snps,dw-csi.txt
> > > new file mode 100644
> > > index 0000000..613b7f9
> > > --- /dev/null
> > > +++ b/Documentation/devicetree/bindings/media/snps,dw-csi.txt
> > > @@ -0,0 +1,41 @@
> > > +Synopsys DesignWare CSI-2 Host controller
> > > +
> > > +Description
> > > +-----------
> > > +
> > > +This HW block is used to receive image coming from an MIPI CSI-2 compatible
> > > +camera.
> > > +
> > > +Required properties:
> > > +- compatible : shall be "snps,dw-csi"
> > > +- reg : physical base address and size of the device memory
> > > + mapped registers;
> > > +- interrupts : DW CSI-2 Host interrupts
> > > +- phys : List of one PHY specifier (as defined in
> > > + Documentation/devicetree/bindings/phy/phy-bindings.txt).
> > > + This PHY is a MIPI DPHY working in RX mode.
> > > +- resets : Reference to a reset controller (optional)
> > > +
> > > +The per-board settings:
> > > + - port sub-node describing a single endpoint connected to the camera as
> > > + described in video-interfaces.txt[1].
> > Which endpoint properties in video-interfaces.txt are relevant for the
> > hardware? Which values may they have?
> >
>
> Currently I'm using only two properties "data-lanes" and "bus-width", but
> I have plans to add blanking info also.
> I will add more info.

Isn't blanking defined by what the transmitter seneds? Or do you have
hardware limitations on the receiver side?

I've only heard of one such case before, and it was a very old parallel
receiver.

If you have a CSI-2 receiver, bus-width isn't relevant --- it's for paralle
interfaces only. Please add data-lanes to required endpoint properties.

--
Regards,

Sakari Ailus

\
 
 \ /
  Last update: 2019-07-09 20:27    [W:0.053 / U:9.124 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site