lkml.org 
[lkml]   [2019]   [Jul]   [9]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
SubjectRE: [v4 4/6] dt-bindings: phy: Document the Synopsys MIPI DPHY Rx bindings
Date
From: Rob Herring <robh@kernel.org>
Date: Tue, Jul 09, 2019 at 15:20:00

> On Tue, Jun 11, 2019 at 09:20:53PM +0200, Luis Oliveira wrote:
> > Add device-tree bindings documentation for SNPS DesignWare MIPI D-PHY in
> > RX mode.
> >
> > Signed-off-by: Luis Oliveira <luis.oliveira@synopsys.com>
> > ---
> > Changelog
> > v3-v4
> > - @Laurent I know I told you I could remove the snps,dphy-frequency on V3 but
> > it is really useful for me here. I removed all other the proprietary
> > properties except this one. Do you still think it must be removed?
> > - Frequency units @Rob
>
> Frequency units means append '-khz' to the property name. That also
> makes the 'frequency' part redundant, so maybe name it more around what
> the frequency is. The frequency for what?
>
> Rob
>

This is the D-PHY high speed frequency configuration that corresponds to
the high speed data transfer of the bus.
Basically is the transmission speed per lane.
Do you think I can use "link-frequencies" (present in
video-interfaces.txt) with one frequency?


> >
> > .../devicetree/bindings/phy/snps,dw-dphy-rx.txt | 29 ++++++++++++++++++++++
> > 1 file changed, 29 insertions(+)
> > create mode 100644 Documentation/devicetree/bindings/phy/snps,dw-dphy-rx.txt
> >
> > diff --git a/Documentation/devicetree/bindings/phy/snps,dw-dphy-rx.txt b/Documentation/devicetree/bindings/phy/snps,dw-dphy-rx.txt
> > new file mode 100644
> > index 0000000..50603e6
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/phy/snps,dw-dphy-rx.txt
> > @@ -0,0 +1,29 @@
> > +Synopsys DesignWare MIPI Rx D-PHY block details
> > +
> > +Description
> > +-----------
> > +
> > +The Synopsys MIPI D-PHY controller supports MIPI-DPHY in receiver mode.
> > +Please refer to phy-bindings.txt for more information.
> > +
> > +Required properties:
> > +- compatible : Shall be "snps,dw-dphy-rx".
> > +- #phy-cells : Must be 1.
> > +- bus-width : Size of the test interface data bus (8 bits->8 or
> > + 12bits->12).
> > +- snps,dphy-frequency : Frequency at which D-PHY should start, configurable.
> > + Check Synopsys databook. (-kHz)
> > +- reg : Test interface register. This correspondes to the
> > + physical base address of the controller and size of
> > + the device memory mapped registers; Check Synopsys
> > + databook.
> > +
> > +Example:
> > +
> > + mipi_dphy_rx1: dphy@d00003040 {
> > + compatible = "snps,dw-dphy-rx";
> > + #phy-cells = <1>;
> > + bus-width = <12>;
> > + snps,dphy-frequency = <300000>;
> > + reg = <0xd0003040 0x20>;
> > + };
> > --
> > 2.7.4
> >

Thank you Rob,
Luis

\
 
 \ /
  Last update: 2019-07-09 18:30    [W:0.071 / U:1.200 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site