lkml.org 
[lkml]   [2019]   [Jul]   [5]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
SubjectRe: [PATCH V3 1/2] dt-bindings: reset: imx7: Add support for i.MX8MM
From
Date
Hi Anson,

On Fri, 2019-07-05 at 00:26 +0000, Anson Huang wrote:
> Hi, Philipp
>
> > On Thu, 2019-07-04 at 17:44 +0800, Anson.Huang@nxp.com wrote:
> > > From: Anson Huang <Anson.Huang@nxp.com>
> > >
> > > i.MX8MM can reuse i.MX8MQ's reset driver, update the compatible
> > > property and related info to support i.MX8MM.
> > >
> > > Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
> > > ---
> > > Changes since V2:
> > > - Add separate line for i.MX8MM in case anything different later for
> >
> > i.MX8MM.
> > > ---
> > > Documentation/devicetree/bindings/reset/fsl,imx7-src.txt | 6 ++++--
> > > 1 file changed, 4 insertions(+), 2 deletions(-)
> > >
> > > diff --git a/Documentation/devicetree/bindings/reset/fsl,imx7-src.txt
> > > b/Documentation/devicetree/bindings/reset/fsl,imx7-src.txt
> > > index 13e0951..c2489e4 100644
> > > --- a/Documentation/devicetree/bindings/reset/fsl,imx7-src.txt
> > > +++ b/Documentation/devicetree/bindings/reset/fsl,imx7-src.txt
> > > @@ -8,6 +8,7 @@ Required properties:
> > > - compatible:
> > > - For i.MX7 SoCs should be "fsl,imx7d-src", "syscon"
> > > - For i.MX8MQ SoCs should be "fsl,imx8mq-src", "syscon"
> > > + - For i.MX8MM SoCs should be "fsl,imx8mm-src", "fsl,imx8mq-src",
> >
> > "syscon"
> > > - reg: should be register base and length as documented in the
> > > datasheet
> > > - interrupts: Should contain SRC interrupt @@ -46,5 +47,6 @@ Example:
> > >
> > >
> > > For list of all valid reset indices see
> > > -<dt-bindings/reset/imx7-reset.h> for i.MX7 and
> > > -<dt-bindings/reset/imx8mq-reset.h> for i.MX8MQ
> > > +<dt-bindings/reset/imx7-reset.h> for i.MX7,
> > > +<dt-bindings/reset/imx8mq-reset.h> for i.MX8MQ and
> > > +<dt-bindings/reset/imx8mq-reset.h> for i.MX8MM
> >
> > The last line is misleading, as that file contains reset indices that are invalid
> > for i.MX8MM.
>
> What is your suggestion about this line?

I would prefer to add an imx8mm-reset.h with only the existing reset
bits, using the IMX8MM_RESET_ prefix. That would make it easy to spot
errors in the dtsi (anything starting with IMX8MQ_ is potentially
wrong).

> Just NOT change it?

The change is good in principle. It just should point to an imx8mm-
reset.h with only the existing resets on i.MX8MM, or imx8mq-reset.h
should be modified to actually make clear which resets are valid on
i.MX8MM.

> Or adding a new file imx8mm-reset.h but still use the IMX8MQ_RESET_ as
> prefix ?

I don't think you should redefine the same macros in imx8mm-reset.h. In
this case using IMX8MM_RESET_ would be better.
> Or keep what I changed, but adding some comments in those macros that
> i.MX8MM does NOT support?

That would be acceptable as well.

regards
Philipp

\
 
 \ /
  Last update: 2019-07-05 10:02    [W:0.053 / U:7.996 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site