lkml.org 
[lkml]   [2019]   [Jul]   [3]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH v2 2/7] net: phy: realtek: Allow disabling RTL8211E EEE LED mode
From
Date
On 03.07.2019 21:37, Matthias Kaehlcke wrote:
> EEE LED mode is enabled by default on the RTL8211E. Disable it when
> the device tree property 'realtek,eee-led-mode-disable' exists.
>
> The magic values to disable EEE LED mode were taken from the RTL8211E
> datasheet, unfortunately they are not further documented.
>
> Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
> ---
> Changes in v2:
> - patch added to the series
> ---
> drivers/net/phy/realtek.c | 37 ++++++++++++++++++++++++++++++++++++-
> 1 file changed, 36 insertions(+), 1 deletion(-)
>
> diff --git a/drivers/net/phy/realtek.c b/drivers/net/phy/realtek.c
> index a669945eb829..eb815cbe1e72 100644
> --- a/drivers/net/phy/realtek.c
> +++ b/drivers/net/phy/realtek.c
> @@ -9,8 +9,9 @@
> * Copyright (c) 2004 Freescale Semiconductor, Inc.
> */
> #include <linux/bitops.h>
> -#include <linux/phy.h>
> #include <linux/module.h>
> +#include <linux/of.h>
> +#include <linux/phy.h>
>
> #define RTL821x_PHYSR 0x11
> #define RTL821x_PHYSR_DUPLEX BIT(13)
> @@ -26,6 +27,10 @@
> #define RTL821x_EXT_PAGE_SELECT 0x1e
> #define RTL821x_PAGE_SELECT 0x1f
>
> +/* RTL8211E page 5 */
> +#define RTL8211E_EEE_LED_MODE1 0x05
> +#define RTL8211E_EEE_LED_MODE2 0x06
> +
> #define RTL8211F_INSR 0x1d
>
> #define RTL8211F_TX_DELAY BIT(8)
> @@ -53,6 +58,35 @@ static int rtl821x_write_page(struct phy_device *phydev, int page)
> return __phy_write(phydev, RTL821x_PAGE_SELECT, page);
> }
>
> +static int rtl8211e_disable_eee_led_mode(struct phy_device *phydev)
> +{

You define return type int but AFAICS the return value is never used,
also in subsequent patches.

> + int ret = 0;
> + int oldpage;
> +
> + oldpage = phy_select_page(phydev, 5);
> + if (oldpage < 0)
> + goto out;
> +
> + /* write magic values to disable EEE LED mode */
> + ret = __phy_write(phydev, RTL8211E_EEE_LED_MODE1, 0x8b82);
> + if (ret)
> + goto out;
> +
> + ret = __phy_write(phydev, RTL8211E_EEE_LED_MODE2, 0x052b);
> +
> +out:
> + return phy_restore_page(phydev, oldpage, ret);
> +}
> +
> +static int rtl8211e_config_init(struct phy_device *phydev)
> +{
> + struct device *dev = &phydev->mdio.dev;
> +
> + if (of_property_read_bool(dev->of_node, "realtek,eee-led-mode-disable"))
> + rtl8211e_disable_eee_led_mode(phydev);
> +
> + return 0;
> +}

I suppose checkpatch complains about the missing empty line.
You add it in a later patch, in case of a v3 you could fix that.

> static int rtl8201_ack_interrupt(struct phy_device *phydev)
> {
> int err;
> @@ -310,6 +344,7 @@ static struct phy_driver realtek_drvs[] = {
> .name = "RTL8211E Gigabit Ethernet",
> .config_init = &rtl8211e_config_init,
> .ack_interrupt = &rtl821x_ack_interrupt,
> + .config_init = &rtl8211e_config_init,
> .config_intr = &rtl8211e_config_intr,
> .suspend = genphy_suspend,
> .resume = genphy_resume,
>

\
 
 \ /
  Last update: 2019-07-03 22:15    [W:0.137 / U:21.116 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site