lkml.org 
[lkml]   [2019]   [Jul]   [24]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Subject[PATCH 0/3] drm: bridge: Add NWL MIPI DSI host controller support
Date
This adds initial support for the NWL MIPI DSI Host controller found on i.MX8
SoCs.

It adds support for the i.MX8MQ but the same IP core can also be found on e.g.
i.MX8QXP. I added the necessary hooks to support other imx8 variants but since
I only have imx8mq boards to test I omitted the platform data for other SoCs.

The code is based on NXPs BSP so I added Robert Chiras as
Co-authored-by. Robert, if this looks sane could you add your
Signed-off-by:?

The most notable changes over the BSP driver are
- Calculate HS mode timing from phy_configure_opts_mipi_dphy
- Perform all clock setup via DT
- Merge nwl-imx and nwl drivers
- Add B0 silion revision quirk
- become a bridge driver to hook into mxsfb (from what I read[0] DCSS, which
also can drive the nwl on the imx8mq will likely not become part of
imx-display-subsystem so it makes sense to make it drive a bridge for dsi as
well).
- Use panel_bridge to attach the panel

This has been tested on a Librem 5 devkit using mxsfb with Robert's patches[1]
and the rocktech-jh057n00900 panel driver. The DCSS can later on also act as
input source too.

Changes from v0:
- Add quirk for IMQ8MQ silicon B0 revision to not mess with the
system reset controller on power down since enable() won't work
otherwise.
- Drop devm_free_irq() handled by the device driver core
- Disable tx esc clock after the phy power down to unbreak
disable/enable (unblank/blank)
- Add ports to dt binding docs
- Select GENERIC_PHY_MIPI_DPHY instead of GENERIC_PHY for
phy_mipi_dphy_get_default_config
- Select DRM_MIPI_DSI
- Include drm_print.h to fix build on next-20190408
- Drop some debugging messages
- Newline terminate all DRM_ printouts
- Turn component driver into a drm bridge

[0]: https://lists.freedesktop.org/archives/dri-devel/2019-May/219484.html
[1]: https://patchwork.freedesktop.org/series/62822/

Guido Günther (3):
arm64: imx8mq: add imx8mq iomux-gpr field defines
dt-bindings: display/bridge: Add binding for IMX NWL mipi dsi host
controller
drm/bridge: Add NWL MIPI DSI host controller support

.../bindings/display/bridge/imx-nwl-dsi.txt | 89 +++
drivers/gpu/drm/bridge/Kconfig | 2 +
drivers/gpu/drm/bridge/Makefile | 1 +
drivers/gpu/drm/bridge/imx-nwl/Kconfig | 15 +
drivers/gpu/drm/bridge/imx-nwl/Makefile | 2 +
drivers/gpu/drm/bridge/imx-nwl/nwl-drv.c | 529 +++++++++++++
drivers/gpu/drm/bridge/imx-nwl/nwl-drv.h | 72 ++
drivers/gpu/drm/bridge/imx-nwl/nwl-dsi.c | 745 ++++++++++++++++++
drivers/gpu/drm/bridge/imx-nwl/nwl-dsi.h | 111 +++
include/linux/mfd/syscon/imx8mq-iomuxc-gpr.h | 62 ++
10 files changed, 1628 insertions(+)
create mode 100644 Documentation/devicetree/bindings/display/bridge/imx-nwl-dsi.txt
create mode 100644 drivers/gpu/drm/bridge/imx-nwl/Kconfig
create mode 100644 drivers/gpu/drm/bridge/imx-nwl/Makefile
create mode 100644 drivers/gpu/drm/bridge/imx-nwl/nwl-drv.c
create mode 100644 drivers/gpu/drm/bridge/imx-nwl/nwl-drv.h
create mode 100644 drivers/gpu/drm/bridge/imx-nwl/nwl-dsi.c
create mode 100644 drivers/gpu/drm/bridge/imx-nwl/nwl-dsi.h
create mode 100644 include/linux/mfd/syscon/imx8mq-iomuxc-gpr.h

--
2.20.1

\
 
 \ /
  Last update: 2019-07-24 17:53    [W:0.107 / U:6.292 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site