lkml.org 
[lkml]   [2019]   [Jul]   [10]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
SubjectRe: [v4 1/6] dt-bindings: media: Document bindings for DW MIPI CSI-2 Host
Date


On 09.07.2019 20:08, Luis de Oliveira wrote:

>
> Hi Eugen,
>
>
> From: Eugen.Hristev@microchip.com <Eugen.Hristev@microchip.com>
> Date: Tue, Jul 09, 2019 at 15:33:50
>
>>
>>
>> On 11.06.2019 22:20, Luis Oliveira wrote:
>>> From: Luis Oliveira <lolivei@synopsys.com>
>>>
>>> Add bindings for Synopsys DesignWare MIPI CSI-2 host.
>>>
>>> Signed-off-by: Luis Oliveira <lolivei@synopsys.com>
>>> ---
>>> Changelog
>>> v3-v4
>>> - remove "plat" from the block name @rob @laurent
>>> - remove "phy-names" when single-entry @rob
>>> - remove "snps,output-type" -> went to the driver config @laurent
>>>
>>> .../devicetree/bindings/media/snps,dw-csi.txt | 41 ++++++++++++++++++++++
>>> 1 file changed, 41 insertions(+)
>>> create mode 100644 Documentation/devicetree/bindings/media/snps,dw-csi.txt
>>>
>>> diff --git a/Documentation/devicetree/bindings/media/snps,dw-csi.txt b/Documentation/devicetree/bindings/media/snps,dw-csi.txt
>>> new file mode 100644
>>> index 0000000..613b7f9
>>> --- /dev/null
>>> +++ b/Documentation/devicetree/bindings/media/snps,dw-csi.txt
>>> @@ -0,0 +1,41 @@
>>> +Synopsys DesignWare CSI-2 Host controller
>>> +
>>> +Description
>>> +-----------
>>> +
>>> +This HW block is used to receive image coming from an MIPI CSI-2 compatible
>>> +camera.
>>> +
>>> +Required properties:
>>> +- compatible : shall be "snps,dw-csi"
>>> +- reg : physical base address and size of the device memory
>>> + mapped registers;
>>> +- interrupts : DW CSI-2 Host interrupts
>>> +- phys : List of one PHY specifier (as defined in
>>> + Documentation/devicetree/bindings/phy/phy-bindings.txt).
>>> + This PHY is a MIPI DPHY working in RX mode.
>>> +- resets : Reference to a reset controller (optional)
>>> +
>>> +The per-board settings:
>>> + - port sub-node describing a single endpoint connected to the camera as
>>> + described in video-interfaces.txt[1].
>>> +
>>> +Example:
>>> +
>>> + csi2: csi2@3000 {
>>> + compatible = "snps,dw-csi";
>>> + #address-cells = <1>;
>>> + #size-cells = <0>;
>>> + reg = < 0x03000 0x7FF>;
>>> + phys = <&mipi_dphy_rx>;
>>> + resets = <&dw_rst 1>;
>>> + interrupts = <2>;
>>> +
>>> + port@0 {
>>> + reg = <0>;
>>> + csi_ep1: endpoint {
>>> + remote-endpoint = <&camera_1>;
>>> + data-lanes = <1 2>;
>>> + };
>>
>> Hello Luis,
>>
>> Which is the output port (endpoint) : how to connect the output of
>> csi2host to another node ?
>> I mean, the second port of this block, or, how is the data taken from
>> csi2host ?
>>
>
> I understand your question, I think you guessed this is not the complete
> pipeline (I have a top driver that interacts with this one).
> I was not planning to submit it, do you think I should?

Yes please, you can have the patch with subject DO NOT MERGE if you do
not want that patch to be included in the kernel and just for reference.
but it would help me in understanding your setup

Thanks !

>
> The behavior is very similar with this one
> ./drivers/media/platform/exynos4-is/media-dev.c
>
>
>> Thanks,
>>
>> Eugen
>>
>>> + };
>>> + };
>>>
>
> Thanks,
> Luis
>
\
 
 \ /
  Last update: 2019-07-10 08:53    [W:0.064 / U:0.112 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site