lkml.org 
[lkml]   [2019]   [Jun]   [11]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH 1/3] Documentation: dt-bindings: add the Amlogic Meson Temperature Sensor
From
Date
On 06/06/2019 21:16, Martin Blumenstingl wrote:
> Hi Guillaume,
>
> thank you for working on this!
>
> On Tue, Jun 4, 2019 at 4:47 PM Guillaume La Roque <glaroque@baylibre.com> wrote:
>>
>> This adds the devicetree binding documentation for the Temperature
>> Sensor found in the Amlogic Meson G12 SoCs.
>> Currently only the G12A SoCs are supported.
> so G12B is not supported (yet)?

G12B is 95% similar as G12A, it will certainly use slighly different values.

>
>> Signed-off-by: Guillaume La Roque <glaroque@baylibre.com>
>> ---
>> .../iio/temperature/amlogic,meson-tsensor.txt | 31 +++++++++++++++++++
>> 1 file changed, 31 insertions(+)
>> create mode 100644 Documentation/devicetree/bindings/iio/temperature/amlogic,meson-tsensor.txt
>>
>> diff --git a/Documentation/devicetree/bindings/iio/temperature/amlogic,meson-tsensor.txt b/Documentation/devicetree/bindings/iio/temperature/amlogic,meson-tsensor.txt
>> new file mode 100644
>> index 000000000000..d064db0e9cac
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/iio/temperature/amlogic,meson-tsensor.txt
>> @@ -0,0 +1,31 @@
>> +* Amlogic Meson Temperature Sensor
>> +
>> +Required properties:
>> +- compatible: depending on the SoC and the position of the sensor,
>> + this should be one of:
>> + - "amlogic,meson-g12a-cpu-tsensor" for the CPU G12A SoC sensor
>> + - "amlogic,meson-g12a-ddr-tsensor" for the DDR G12A SoC sensor
>> + followed by the common :
>> + - "amlogic,meson-g12a-tsensor" for G12A SoC family
>> +- reg: the physical base address and length of the registers
>> +- interrupts: the interrupt indicating end of sampling
>> +- clocks: phandle identifier for the reference clock of temperature sensor
>> +- #io-channel-cells: must be 1, see ../iio-bindings.txt
> have you considered using the thermal framework [0] instead of the iio
> framework (see below)?

Question: why thermal, and not hwmon ? what's the main difference ?

>
>> +- amlogic,ao-secure: phandle to the ao-secure syscon
> the driver has some "u_efuse_off" access. do we need to get some
> calibration values from the AO syscon or can we also fetch it from the
> eFuse? you can look at arch/arm/boot/dts/meson8.dtsi where I'm passing
> the temperature sensor calibration data to the SAR ADC (there's no
> dedicated temperature sensor IP block prior to G12A) while reading the
> data from the eFuse
>
>> +Optional properties:
>> +- amlogic,critical-temperature: temperature value in milli degrees Celsius
>> + to set automatic reboot on too high temperature
> as far as I can tell the thermal framework supports multiple trip
> points. I'm seeing this as a benefit because the hardware can raise
> interrupts at four different temperatures (defined by the driver)

Theoretically, but the implementation code differs a lot from the datasheet.

>
>> +Example:
>> + cpu_temp: temperature-sensor@ff634800 {
>> + compatible = "amlogic,meson-g12a-cpu-tsensor",
>> + "amlogic,meson-g12a-tsensor";
>> + reg = <0x0 0xff634800 0x0 0x50>;
>> + interrupts = <GIC_SPI 35 IRQ_TYPE_EDGE_RISING>;
>> + clocks = <&clkc CLKID_TS>;
>> + status = "okay";
> as far as I know the dt-bindings should not have a status property in
> the examples
>
>
> Martin
>
> _______________________________________________
> linux-amlogic mailing list
> linux-amlogic@lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-amlogic
>

\
 
 \ /
  Last update: 2019-06-11 13:02    [W:0.093 / U:5.248 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site