lkml.org 
[lkml]   [2019]   [May]   [8]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
SubjectRE: [EXT] Re: [PATCH 1/3] dt-bindings: i2c: add optional mul-value property to binding
Date


> -----Original Message-----
> From: Rob Herring <robh@kernel.org>
> Sent: 2019年5月3日 4:59
> To: Chuanhua Han <chuanhua.han@nxp.com>
> Cc: mark.rutland@arm.com; shawnguo@kernel.org; s.hauer@pengutronix.de;
> Leo Li <leoyang.li@nxp.com>; linux-kernel@vger.kernel.org;
> devicetree@vger.kernel.org; linux-arm-kernel@lists.infradead.org;
> linux-i2c@vger.kernel.org; kernel@pengutronix.de; dl-linux-imx
> <linux-imx@nxp.com>; festevam@gmail.com;
> wsa+renesas@sang-engineering.com; u.kleine-koenig@pengutronix.de;
> eha@deif.com; linux@rempel-privat.de; Sumit Batra <sumit.batra@nxp.com>;
> l.stach@pengutronix.de; peda@axentia.se
> Subject: [EXT] Re: [PATCH 1/3] dt-bindings: i2c: add optional mul-value
> property to binding
>
> Caution: EXT Email
>
> On Tue, Apr 30, 2019 at 12:32:40PM +0800, Chuanhua Han wrote:
> > NXP Layerscape SoC have up to three MUL options available for all
> > divider values, we choice of MUL determines the internal monitor rate
> > of the I2C bus (SCL and SDA signals):
> > A lower MUL value results in a higher sampling rate of the I2C signals.
> > A higher MUL value results in a lower sampling rate of the I2C signals.
> >
> > So in Optional properties we added our custom mul-value property in
> > the binding to select which mul option for the device tree i2c
> > controller node.
> >
> > Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
> > ---
> > Documentation/devicetree/bindings/i2c/i2c-imx.txt | 3 +++
> > 1 file changed, 3 insertions(+)
> >
> > diff --git a/Documentation/devicetree/bindings/i2c/i2c-imx.txt
> > b/Documentation/devicetree/bindings/i2c/i2c-imx.txt
> > index b967544590e8..ba8e7b7b3fa8 100644
> > --- a/Documentation/devicetree/bindings/i2c/i2c-imx.txt
> > +++ b/Documentation/devicetree/bindings/i2c/i2c-imx.txt
> > @@ -18,6 +18,9 @@ Optional properties:
> > - sda-gpios: specify the gpio related to SDA pin
> > - pinctrl: add extra pinctrl to configure i2c pins to gpio function for i2c
> > bus recovery, call it "gpio" state
> > +- mul-value: NXP Layerscape SoC have up to three MUL options
> > +available for all I2C divider values, it describes which MUL we
> > +choose to use for the driver, the values should be 1,2,4.
>
> Needs a vendor prefix. I don't find 'value' to add anything nor do I understand
> what MUL is.
Yes,you are right!
>
> If it is determined by SoC rather than board, then it should perhaps be implied
> by compatible.
This is determined by the SOC, but it has three options to choose from,
so I think it's better to use the optional option instead of compatible

>
> Rob
\
 
 \ /
  Last update: 2019-05-08 13:47    [W:0.100 / U:0.812 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site