lkml.org 
[lkml]   [2019]   [May]   [23]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH v9 0/4] vfio: ap: AP Queue Interrupt Control
From
Date
On 5/21/19 11:34 AM, Pierre Morel wrote:
> This patch series implements PQAP/AQIC interception in KVM.
>
> 1) Data to handle GISA interrupt for AQIC
>
> To implement this we need to add a new structure, vfio_ap_queue,
> to be able to retrieve the mediated device associated with a queue
> and specific values needed to register/unregister the interrupt
> structures:
> - APQN: to be able to issue the commands and search for queue
> structures
> - saved NIB : to keep track of the pin page for unpining it
> - saved ISC : to unregister with the GIB interface
> - matrix_mdev: to retrieve the associate matrix, the mediated device
> and KVM
>
> Specific handling bei keeping old values when re-registering is
> needed because the guest could unregister interrupt in a invisble
> manner bei issuing an un-interceptible RESET command.
>
> Reset commands issued directly by the guest and indirectly when
> removing the guest unpin the memory and deregister the ISC.
>
> The vfio_ap_queue is associated to the ap_device during the probe
> of the device and dissociated during the remove of the ap_device.
>
> The vfio_ap_queue is associated to the matrix mediated device during
> each interception of the AQIC command, so it does not need to be
> dissociated until the guest is terminated.
>
> The life of the vfio_ap_queue will be protected by the matrix_dev lock
> to guaranty that no change can occur to the CRYCB or that devices can
> not be removed when a vfio_ap_queue is in use.
>
> 2) KVM destroy race conditions
>
> To make sure that KVM do not vanish and GISA is still available
> when the VFIO_AP driver is in used we take a reference to KVM
> during the opening of the mediated device and release it on
> releasing the mediated device.
>
> 3) Interception of PQAP
>
> The driver registers a hook structure to KVM providing:
> - a pointer to a function implementing PQAP(AQIC) handling
> - the reference to the module owner of the hook
>
> On interception by KVM we do not change the behavior, returning
> -EOPNOTSUPP to the user in the case AP instructions are not
> supported by the host or by the guest.
> Otherwise we verify the exceptions cases before trying to call
> the vfio_ap hook.
>
> In the case we do not find a hook we assume that the CRYCB has not
> been setup for the guest and is empty.
>
> 4) Enabling and disabling the IRQ
>
> When enabling the IRQ care is taken to unping the saved NIB.
> When disabling IRQ care is taken to wait until the IRQ bit
> of the queue status is cleared before unpining the NIB.
>
> On RESET and before unpinning the NIB and unregistering the ISC
> the IRQ is disabled using PQAP/AQIC even when a PQAP/APZQ have
> been done.
>
> 5) Removing the AP device
>
> Removing the AP device without having unassign it is clearly
> discourage by the documentation.
> The patch series does not check if the queue is used by a
> guest. It only de-register the IRQ, unregister ISC and unpin
> the NIB, then free the vfio_ap_queue.
>
> 6) Associated QEMU patch
>
> There is a QEMU patch which is needed to enable the PQAP/AQIC
> facility in the guest.
>
> Posted in qemu-devel@nongnu.org as:
> Message-Id: <1550146494-21085-1-git-send-email-pmorel@linux.ibm.com>
>
> 7) Compatibility with Dynamic configuration patches
>
> Tony, I did not rebase this series above the dynamic configuration
> patches because:
> - This series do the work it needs to do without having to take
> care on the dynamic configuration.
> - It is guarantied that interrupt will be shut off after removing
> the APQueue device
> - The dynamic configuration series is not converging.

Would you consider the following?

* Take dynconfig patch "s390: vfio-ap: wait for queue empty on queue
reset" and include it in your series. This patch modifies the
reset function to wait for queue empty.

* In dynconfig patch "s390: vfio-ap: handle bind and unbind of AP queue
device" the following functions are introduced:

void vfio_ap_mdev_probe_queue(struct ap_queue *queue)
void vfio_ap_mdev_remove_queue(struct ap_queue *queue)

The vfio_ap_mdev_probe_queue function is called from the vfio_ap
driver probe callback. You could embed the code you've introduced in
the probe callback there. Of course, you would need to return int
from the function for the -ENOMEM error.

The vfio_ap_mdev_remove_queue function is called from the vfio_ap
driver remove callback. You could embed the code you've introduced in
the remove callback there.

* Move your vfio_ap_irq_disable function to vfio_ap_ops.c and make it a
static function.

* Leave the vfio_ap_mdev_reset_queue function as a static function in
vfio_ap_ops.c

If you do the things above, then I can base the dynconfig series on
the IRQ series without much of a merge issue. What say you?

Note: I've included review comments for patch 3/4 to match the
suggestions above.

>
> However Tony, the choice is your's, I won't be able to help
> in a near future.
>
>
> Pierre Morel (4):
> s390: ap: kvm: add PQAP interception for AQIC
> vfio: ap: register IOMMU VFIO notifier
> s390: ap: implement PAPQ AQIC interception in kernel
> s390: ap: kvm: Enable PQAP/AQIC facility for the guest
>
> arch/s390/include/asm/kvm_host.h | 7 +
> arch/s390/kvm/priv.c | 86 ++++++++
> arch/s390/tools/gen_facilities.c | 1 +
> drivers/s390/crypto/vfio_ap_drv.c | 34 ++-
> drivers/s390/crypto/vfio_ap_ops.c | 379 +++++++++++++++++++++++++++++++++-
> drivers/s390/crypto/vfio_ap_private.h | 15 ++
> 6 files changed, 514 insertions(+), 8 deletions(-)
>

\
 
 \ /
  Last update: 2019-05-23 17:37    [W:0.090 / U:1.496 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site