lkml.org 
[lkml]   [2019]   [May]   [21]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Date
SubjectRe: [PATCH] arm64: dts: allwinner: a64-oceanic-5205-5inmfd: Enable CAN
Hi Maxime

On Thu, Apr 18, 2019 at 4:56 PM Maxime Ripard <maxime.ripard@bootlin.com> wrote:
>
> On Thu, Apr 18, 2019 at 07:46:58PM +0530, Jagan Teki wrote:
> > Oceanic 5205 5inMFD has MCP2515 CAN device connected via SPI1.
> >
> > - via SPI1 bus
> > - vdd supplied by 5V supply along with PL2 enable pin
> > - xceiver supply same as vdd
> > - can oscillator connected at 20MHz
> > - PB2 gpio as interrupt pin
> > - PD6 gpio as RX_BUF1_CAN0
> > - PD7 gpio as RX_BUF0_CAN0
> >
> > Tested-by: Tamas Papp <tamas@osukl.com>
> > Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
> > ---
> > .../sun50i-a64-oceanic-5205-5inmfd.dts | 43 +++++++++++++++++++
> > 1 file changed, 43 insertions(+)
> >
> > diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-oceanic-5205-5inmfd.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-oceanic-5205-5inmfd.dts
> > index f0cd6587f619..22535a297f51 100644
> > --- a/arch/arm64/boot/dts/allwinner/sun50i-a64-oceanic-5205-5inmfd.dts
> > +++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-oceanic-5205-5inmfd.dts
> > @@ -21,6 +21,24 @@
> > chosen {
> > stdout-path = "serial0:115200n8";
> > };
> > +
> > + can_osc: can-osc {
> > + compatible = "fixed-clock";
> > + #clock-cells = <0>;
> > + clock-frequency = <20000000>;
> > + };
> > +
> > + reg_can_v5v: reg-can-v5v {
> > + compatible = "regulator-fixed";
> > + regulator-name = "reg-can-v5v";
> > + regulator-min-microvolt = <5000000>;
> > + regulator-max-microvolt = <5000000>;
> > + regulator-boot-on;
> > + enable-active-high;
> > + gpio = <&r_pio 0 2 GPIO_ACTIVE_HIGH>; /* CAN_3V3_EN: PL2 */
> > + status = "okay";
>
> You don't need the status property here.
>

Correct, need to be dropped

> > + };
> > +
> > };
> >
> > &ehci0 {
> > @@ -77,6 +95,31 @@
> > status = "okay";
> > };
> >
> > +&pio {
> > + can_pins: can-pins {
> > + pins = "PD6", /* RX_BUF1_CAN0 */
> > + "PD7"; /* RX_BUF0_CAN0 */
> > + function = "gpio_in";
> > + };
> > +};
>
> That isn't needed. What are they used for, you're not tying them to
> anything?

Mux of their function is correct. They are connected in the schematics
but not used right now.
I can garantee that kernel wlll always configurred in the right way
and if I want I can export in userspace
for debug purpose

Michael


>
> Maxime
>
> --
> Maxime Ripard, Bootlin
> Embedded Linux and Kernel engineering
> https://bootlin.com



--
| Michael Nazzareno Trimarchi Amarula Solutions BV |
| COO - Founder Cruquiuskade 47 |
| +31(0)851119172 Amsterdam 1018 AM NL |
| [`as] http://www.amarulasolutions.com |

\
 
 \ /
  Last update: 2019-05-21 08:48    [W:0.061 / U:4.596 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site